Schneider MTN629993 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Schneider MTN629993 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
GB
¼
DANGER
Risk of fatal injury from electrical current.
All work on the device should only be carried out
by trained and skilled electricians. Observe the
country-specific regulations as well as the valid
KNX guidelines.
½CAUTION
The device could be damaged.
Only operate the device according to the
specifications stated in the Technical data.
The switch actuator UP/230/16 (referred to below as the
actuator) can switch one load via a floating make
contact.
Mount the actuator in a wall or ceiling socket-outlet with
a diameter of 60 mm and a depth of at least 40 mm. For
ceiling mounting, the hook on which the luminaire is
suspended can be screwed onto the ceiling socket-
outlet through the centre hole in the actuator.
AConnection of electrical loads, AC 230 V
BProgramming button
CBus connecting terminal
DProgramming LED (red)
For your safety
Getting to know the switch actuator
Connections, displays and operating
elements
CB
A
D
1Mount the actuator in a flush-mounted box at least
40 mm deep.
Use the opposite entry openings A of the installation
box for the 230 V cable and the bus line. The actuator
itself serves as a separating web.
2 BConnect KNX . The sheath of the bus line must
be cut back as short as possible at the bus
terminal.
½WARNING
Risk of fatal injury from electrical current. The
device could become damaged.
Safety clearance must be guaranteed in
accordance with IEC 60664-1. There must be at
least 4 mm between the individual cores of the
230 V supply cable and the KNX line.
½CAUTION
The device could be damaged.
If you are switching socket-outlets with the
actuator, it is not possible to ensure that
exclusively ohmic loads are connected. Fuse the
circuit with 10 A.
3Connect the load.
4Connect the bus voltage.
5Connect the load voltage.
1Press the programming button.
The programming LED lights up.
2Load the physical address and application into the
device from the ETS.
The programming LED goes out.
The application was loaded successfully, the device is
ready for operation.
Mounting the actuator
Putting the actuator into operation
B
AA
230 V
4 mm
KNX
KNX L1 N
If you have technical questions, please contact the Cus-
tomer Care Center in your country.
www.schneider-electric.com
This product must be installed, connected and used in
compliance with prevailing standards and/or installati-
on regulations. As standards, specifications and de-
signs develop from time to time, always ask for
confirmation of the information given in this publicati-
on.
Schneider Electric Industries SAS
Technical data
Power supply from
bus:
DC 24 V/approx. 10 mA
Insulation voltage: 4 kV between bus and AC 230 V
Switch contacts: 1 x make contacts
Nominal voltage: AC 230 V, 50 to 60 Hz
Nominal current: 16 A, ohmic load cos Ï• = 1
10 A, inductive load cos Ï• = 0.6
Connected load
Incandescent
lamps: AC 230 V, max. 2700 W with
20,000 switching cycles
Halogen lamps: AC 230 V, max. 1700 W with
20,000 switching cycles
Fluorescent lamps: AC 230 V, max. 1000 VA,
parallel-compensated with
5,000 switching cycles
Capacitive load: AC 230 V, 10 A max. 105 µF
with 5,000 switching cycles
Fuse: The switch contact must be
protected by a series-connected
circuit-breaker.
Switching
frequency: max. 10 per minute at nominal
load
Ambient temperature
Operation: -5 °C to +45 °C
Storage: -25 °C to +55 °C
Transport: -25 °C to +70 °C
Environment: can be used at up to 2000 m
above sea level (MSL)
Operating element: 1 programming button
Display element: 1 red LED: programming check
Connections
Bus: via two 1 mm pins for bus
connecting terminal
Outer conductor: two screw terminals for max.
2.5 mm²
EC guidelines: Complies with Low-Voltage
guideline 73/23/EEC; complies
with EMC guideline 89/336/EEC
Dimensions: 51 x 52 x 29 mm (W x H x D)
Switch actuator, flush-mounted/230/16
Operating instructions
Art. no. MTN629993
V6299-562-00 01/08


Product specificaties

Merk: Schneider
Categorie: Niet gecategoriseerd
Model: MTN629993

Heb je hulp nodig?

Als je hulp nodig hebt met Schneider MTN629993 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Schneider

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd