Satel AMD-103 Handleiding

Satel Deur-/raamsensor AMD-103

Lees hieronder de 📖 handleiding in het Nederlandse voor Satel AMD-103 (4 pagina's) in de categorie Deur-/raamsensor. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

147

AMD-103

WIRELESS MAGNETIC CONTACT

amd103_en 05/15

The AMD-103 magnetic contact can detect opening of a door, window, etc. It is designed for

operation within the ABAX two-way wireless system. This manual applies to the detector with

firmware version 2.00, which is supported by:

 ACU-120 / ACU-270 controller,

 ACU-100 / ACU-250 controller with firmware version 4.03 2014-05-15 (or newer),

 ARU-100 repeater with firmware version 2.00 2014-05-15 (or newer),

 INTEGRA 128-WRL control panel with firmware version 1.12 2013-12-20 (or newer).

1. Features

 LED indicator enabled in test mode.

 Tamper protection in 2 ways – cover removal and tearing enclosure from the wall.

 Battery status control.

2. Specifications

Operating frequency band ...................................................................868.0 MHz ÷ 868.6 MHz

Radio communication range (in open area)............................................................ up to 350 m

Battery ................................................................................................................. CR2477N 3 V

Battery life expectancy...................................................................................... approx. 2 years

Standby current consumption ...........................................................................................10 µA

Maximum current consumption........................................................................................14 mA

Environmental class according to EN50130-5 ......................................................................... II

Operating temperature range.............................................................................-10 °C...+55 °C

Maximum humidity.......................................................................................................... 93±3%

Detector enclosure dimensions........................................................................32 x 45 x 20 mm

Magnet enclosure dimensions .........................................................................11 x 45 x 10 mm

Weight................................................................................................................................. 40 g

Hereby, SATEL sp. z o.o., declares that this detector is in compliance with the

essential requirements and other relevant provisions of Directive 1999/5/EC. The

declaration of conformity may be consulted at www.satel.eu/ce

3. Description

Opening the reed switch contacts after removal of magnet, or opening the tamper contact,

will trigger an alarm. Information on the alarm is sent by radio to the ACU-100 / ACU-250 /

ACU-120 / ACU-270 controller or to INTEGRA 128-WRL control panel. The detector always

remains in the active mode (all alarms are sent immediately).

2 AMD-103 SATEL

Every 15 minutes, the detector sends a transmission with information on the current status of

the reed switch, tamper contact and battery. Periodic transmissions are used to monitor

presence and operation of the magnetic contact.

Note: In the case of the AMD-103 magnetic contact, the presence check is performed in

a different way than for the other ABAX system devices. If the value programmed for

the F

ILTER

parameter differs from 0, the lack of presence will be reported if no

transmission from the detector is received within one hour.

The LED is only working in the test mode:

 it is lit for 80 milliseconds, when the test transmission is being sent;

 it is lit for 2 seconds in the event of alarm.

The test mode is turned on for 20 minutes after inserting the batteries or opening the tamper

contact.

The detector checks the battery status. When the voltage is lower than 2.6 V, the low-battery

information is sent during each transmission.

4. Installation

There is a danger of battery explosion when using a different battery than

recommended by the manufacturer, or handling the battery improperly.

Be particularly careful during installation and replacement of the battery. The

manufacturer is not liable for the consequences of incorrect installation of the

battery.

The used batteries must not be discarded, but should be disposed of in

accordance with the existing rules for environment protection.

The device is designed for indoor installation. The detector should be mounted on a fixed

surface (e.g. window or door frame), and the magnet on a movable surface (e.g. window or

door). Mounting the magnetic contact on ferromagnetic surfaces and/or near to strong

magnetic and electrical fields is not advisable, because it can result in malfunctioning of the

device.

Special designation on the detector enclosure indicates the side on which the magnets

should be installed (Fig. 6).

1. Open the detector enclosure (Fig. 2).

2. Install the battery and add the device to the wireless system (see the ACU-100 / ACU-250 /

ACU-120 / ACU-270 controller manual, installer manuals for INTEGRA 128-WRL or

VERSA control panels).

3. Close the detector enclosure (the tamper contact must be pressed down by the base

element).

4. Fasten the detector temporarily at the place of its future installation.

5. Move the magnet away from the detector. The detector will send information on the alarm,

which will allow you to check the level of signal received from the detector by the

ACU-100 / ACU-250 / ACU-120 / ACU-270 controller or the INTEGRA 128-WRL control

panel. If necessary, select another place for installation, to ensure adequate

communication quality.

6. Open the detector enclosure (Fig. 2).

7. Using wall plugs (screw anchors) and screws, fasten the enclosure base to the mounting

surface (Fig. 3).

8. Close the detector enclosure (the tamper contact must be pressed down by the base

element).

SATEL AMD-103 3

9. Press the catch and open the enclosure containing magnets (Fig. 4).

10. Using wall plugs (screw anchors) and screws, attach the magnet enclosure base to the

mounting surface (Fig. 5). The distance between the detector enclosure and the magnet

enclosure must not be greater than 20 mm (Fig. 6).

11. Replace the magnet enclosure cover.

12. Start the test mode and check whether the LED lights up after moving the magnet away

(i.e. opening a window or door).

Product specificaties

Merk:	Satel
Categorie:	Deur-/raamsensor
Model:	AMD-103
Kleur van het product:	Wit
Connectiviteitstechnologie:	Draadloos
Geschikt voor:	Deur/raam
Interface:	RF Draadloos
Frequentie:	868 - 868.6 MHz
Transmissie-afstand:	350 m
Bedrijfstemperatuur (T-T):	-10 - 55 °C