Ryobi RPP254JO Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Ryobi RPP254JO (44 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 226 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/44
ORIGINAL INSTRUCTIONS
Petrol Pole Pruner
RPP254JO
Important!
It is essential that you read the instructions in this manual before assembling,
operating, and maintaining the product.
Subject to technical modification.
1
Safety, performance, and dependability have been given
top priority in the design of your petrol pole pruner.
INTENDED USE
The petrol pole pruner is only intended for use outdoors.
For safety reasons, the product must be adequately
controlled by a two-handed operation.
The product is designed for cutting and pruning small limbs
and branches (with a diameter less than or equal to the bar
length) located high in the tree. While cutting and pruning,
the operator maintains a steady footing on the ground.
The product is designed to be extended to a maximum
length of 2.7 m. Do not exceed this working length.
It is not intended to be used while climbing or as a
conventional chainsaw for close quarter limbing and
pruning of material at ground level.
Do not use the product for any other purpose.
GENERAL SAFETY WARNINGS
WARNING
For safe operation, read and understand all
instructions before using the product. Follow all
safety instructions, information on correct working
posture, the need for rest periods, and changing working
positions. Failure to follow all safety instructions listed
below, can result in serious personal injury.
READ ALL INSTRUCTIONS
Do not allow children or untrained individuals to use the
product.
Never let anyone use the product who has not received
adequate instructions in the product’s proper use. This
applies to rentals, as well as privately owned products
and also to the power head it is attached to.
Always wear safety glasses with side shields. Everyday
glasses have only impact resistant lenses. They are
NOT safety glasses. Following this rule will reduce the
risk of eye injury.
Wear eye, hearing, and head protection when operating
the product. Hearing protection may restrict the
operator’s ability to hear warning sounds. Pay particular
attention to potential hazards around and inside the
working area.
Wear heavy, long pants, boots, and gloves. Do not
wear loose fitting clothing, short pants, or go barefoot.
Do not wear jewellery of any kind.
Heavy protective clothing may increase operator
fatigue, which could lead to heat stroke. During weather
that is hot and humid, heavy work should be scheduled
for early morning or late afternoon hours when
temperatures are cooler.
Never use the product on the operator’s left side.
Secure long hair above shoulder level to prevent
entanglement in moving parts.
Keep all bystanders, children, and pets at least 15 m
away. Bystanders should be encouraged to wear eye
protection. If you are approached, stop the engine and
cutting attachment. In the case of bladed units, there is
the added risk of injury to bystanders from being struck
with the moving blade in the event of a blade thrust or
other unexpected reaction of the saw.
Do not operate the product when you are tired, ill,
or under the influence of alcohol or drugs, or under
medication.
Do not operate in poor lighting. The operator needs
clear unrestricted vision to identify potential hazards.
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance or exposure
to hot surfaces.
Keep all parts of your body away from any moving part.
To avoid hot surfaces, never operate the product with
the bottom of the engine above waist level.
Do not touch the area around the muffler or cylinder of
the product. These parts get hot from operation. Failure
to heed this warning could result in possible serious
personal injury.
Carry the pruner with the engine stopped, the guide bar
and saw chain to the rear, scabbard on the guide bar
and saw chain, and the muffler away from your body.
Always stop the engine before making any adjustments.
Inspect the product before each use for loose fasteners,
fuel leaks, etc. Replace any damaged parts before use.
Mix and store fuel in a container approved for petrol.
Mix fuel outdoors where there are no sparks or flames.
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
Stop the engine and allow it to cool down before
refueling or storing the product.
Allow the engine to cool down, empty the fuel tank, and
secure the product from moving before transporting in
a vehicle.
Stop the engine. Make sure all moving parts have come
to a complete stop:
before servicing
before clearing a blockage
before checking, cleaning, and working on the
product
before changing accessories
after striking a foreign object
whenever leaving the product unattended
whenever performing maintenance
whenever the product starts to vibrate abnormally
PRUNER SAFETY WARNINGS
Do not use the product when there is a possibility of
thunderstorm or lightning. Store the product safely
indoors.
Ensure all guards, handles are properly fitted and are
in good condition.
Do not start using the product until you have a clear
work area, secure footing, and a planned retreat path
away from the falling branches or limbs.
Beware of the emission of lubricant mist and saw dust.
Wear mask or respirator if required.
During operation, hold the product with both hands. Use


Product specificaties

Merk: Ryobi
Categorie: Niet gecategoriseerd
Model: RPP254JO

Heb je hulp nodig?

Als je hulp nodig hebt met Ryobi RPP254JO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Ryobi

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd