Rupert Neve Designs R6 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Rupert Neve Designs R6 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
R6
Six Space 500 Series Rack
Thank you for your purchase of the R6: Six Space 500 Series Rack. Everyone at Rupert Neve Designs
hopes you enjoy using this tool as much as we have enjoyed designing and building it.
Usage Notes
The R6 has 6 x 500 series slots, with ample power, and a full complement of XLR, TRS and DB-25 I/O
in a portable steel chassis. To use the R6, carefully slide each 500 series module in such that the edge
connector ts snuggly into the slot in the back, and tighten both front panel screws for each module.
The current draw meter will display the total current being used by the installed modules. Channels
7 & 8 do not correspond to a module slot, so the connectors are available to access channels 7-8 of a
connected DB-25 cable. These can also be used to convert the jack type (i.e from DB-25 to XLR, or
from TRS to DB-25)
Link
To enable linking between modules, reset the corresponding jumper located by the card slots to the
LINK position. The linking function is set in pairs so that you can link channels 1-2, 3-4, and 5-6. The
link function is typically used to link the VCA circuitry of compressors (such as our 543 module). Most
other types of units are not linkable unless specically noted by the manufacturer.
R6 Specications
DC Voltage to Units +/-16VDC and +48VDC for phantom power
Max Current 1000mA for modules, 150mA for 48V phantom power
Power Requirements 100-240VAC, 50/60Hz, 50 Watts
Weight 9.5lbs
Dimensions 13” long x 7.5”wide x 5.5” high
2
Front / Back Panel
R6: Six Space 500 Series Rack
Current MeterLink JumperCard Slot
There are three link jumpers,
which can be individually set
to allow linking on Channels
1-2, 3-4, and 5-6
The current meter monitors
the current draw on the
power supply
Each card slot is designed to
fit a standard 500 series
module
Channel 1-6 I/O
Channel 7-8 THRU I/OIEC Input
You can use the channel 7-8
connections access channels
7-8 on a connected DB-25
cable, or to switch between
TRS and XLR
Each channel has a multitude
of I/O options with XLR, TRS
and DB-25
The IEC power input accepts
100-240VAC, 50/60Hz input
with a 50 Watt draw


Product specificaties

Merk: Rupert Neve Designs
Categorie: Niet gecategoriseerd
Model: R6

Heb je hulp nodig?

Als je hulp nodig hebt met Rupert Neve Designs R6 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Rupert Neve Designs

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Elcom

Elcom REN705S Handleiding

17 November 2024
Elcom

Elcom REN230X Handleiding

17 November 2024
Elcom

Elcom REE001X Handleiding

17 November 2024
DEXP

DEXP TN-70F Handleiding

17 November 2024
Sanus

Sanus CALW01 Handleiding

17 November 2024
Sanus

Sanus VF3012 Handleiding

17 November 2024
Sanus

Sanus CFR2144 Handleiding

17 November 2024