Rupert Neve Designs R10 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Rupert Neve Designs R10 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
R10
Ten Space 500 Series Rack
Thank you for your purchase of the R10: Ten Space 500 Series Rack. Everyone at Rupert Neve Designs hopes
you enjoy using this tool as much as we have enjoyed designing and building it.
Usage Notes
The R10 has 10 x 500 series slots, with ample power, and both XLR and TRS inputs and outputs in a
rackmountable 3RU steel chassis. To use the R10, carefully slide each 500 series module in such that the
edge connector card fits snuggly into the slot in the back, and tighten both front panel screws for each
module. The current draw meter will display the total current being used by the installed modules. The
R10 has dual XLR and TRS inputs and outputs. With regard to the parallel XLR and TRS connectors, it is
recommended to connect ONLY ONE input on a given channel at a time (including to a patchbay). For the
outputs, it is generally not problematic to use both outputs to send a signal to two different destinations,
however for different modules, longer cable runs and different destinations, using both outputs in parallel
may cause issues, so be aware when using both outputs simultaneously.
Link
To enable VCA linking between modules, reset the corresponding jumper located by the card slots to the
LINK position. The linking function is set in pairs so that you can link channels 1-2, 3-4, ....etc.. The link func-
tion is typically used to link the VCA circuitry of compressors (such as our 543 module). Most other types of
modules are not linkable unless specifically noted by the manufacturer.
R10 Specifications
DC Voltage to Units +/-16VDC and +48VDC for phantom power
Max Output Current 2650mA total (2400mA modules and 250mA for phantom power)
Power Requirements 100-240VAC, 50/60Hz, 120 Watts
Weight 14lbs
Dimensions 19” long x 7.5”deep x 5.5” high
P/N 775-00029, Rev A
Front / Back Panel
R10: Ten Space 500 Series Rack
Current Meter
Link Jumper
Card Slot
There are three link jumpers,
which can be individually set
to allow VCA linking on
Channels 1-2, 3-4, 5-6, 7-8
and 9-10
The current meter monitors
the current draw on the
power supply
Each card slot is designed to
fit a standard 500 series
module
Channel OutputChannel Input
IEC Input
Each channel features a
balanced XLR and TRS input,
which are wired in parallel.
ONLY CONNECT ONE INPUT
AT A TIME
Each channel features a
balanced XLR & TRS output.
The IEC power input accepts
100-240VAC, 50/60Hz input


Product specificaties

Merk: Rupert Neve Designs
Categorie: Niet gecategoriseerd
Model: R10

Heb je hulp nodig?

Als je hulp nodig hebt met Rupert Neve Designs R10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Rupert Neve Designs

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Elcom

Elcom REN705S Handleiding

17 November 2024
Elcom

Elcom REN230X Handleiding

17 November 2024
Elcom

Elcom REE001X Handleiding

17 November 2024
DEXP

DEXP TN-70F Handleiding

17 November 2024
Sanus

Sanus CALW01 Handleiding

17 November 2024
Sanus

Sanus VF3012 Handleiding

17 November 2024
Sanus

Sanus CFR2144 Handleiding

17 November 2024