Ruckus Wireless ZoneFlex 7372 Handleiding

Ruckus Wireless Access point ZoneFlex 7372

Lees hieronder de 📖 handleiding in het Nederlandse voor Ruckus Wireless ZoneFlex 7372 (4 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Published January 2013, Part Number 800-70415-001 Rev E

ZoneFlex 7352/7372 802.11n

Multimedia Wi-Fi Access Point

Quick Setup Guide

This Quick Setup Guide provides step-by-step instructions on

how to set up your Ruckus Wireless ZoneFlex Access Point. After

completing the steps described in this Guide, you will be able to

place the Access Point (AP) at your site and provide wireless

network access to users.

BEFORE YOU BEGIN

Before deploying Ruckus Wireless products, please check for the

latest software and the release documentation.

• User Guides and Release Notes are available at

http://support.ruckuswireless.com/documents.

• Software Upgrades are available at

http://support.ruckuswireless.com/software.

• Open Source information is available at

http://opensource.ruckuswireless.com.

• Software License and Limited Warranty available at

http://support.ruckuswireless.com/warranty.

PACKAGE CONTENTS

• ZoneFlex 7352/7372 Access Point

• Mounting screws and anchors (2)

• Security screw (1)

• 15/16-inch T-bar clips (2)

• Alignment spacer (1)

• Regulatory flyer

• Declaration of Conformity (country-dependent)

• Product Warranty Statement

• This Quick Setup Guide

SETUP REQUIREMENTS

• A computer running Windows 7 (procedures for other OS’s

are similar)

• One or more of the following:

• A modem (DSL or cable), broadband router, or other

device provided by your Internet Service Provider that

brings Internet access to your site.

• A network switch or a DSL/Internet gateway device.

• Two Ethernet cables (Cat5e or better for PoE in)

• An AC power adapter (sold separately), or

• An 802.3af or 802.3at -compliant Power over Ethernet (PoE)

switch or PoE injector

S TEP 1: CONNECT THE AP TO YOUR COMPUTER

1After removing your Ruckus Wireless AP from its package,

place it next to your computer.

2Using an Ethernet cable, connect your computer’s network

port to the 10/100/1000 port on the AP.

3Using the AC adapter (sold separately), connect the AP to a

convenient (and protected) power source.

• Alternatively, connect the 10/100/1000 port to a PoE

injector or PoE switch for both power and network con-

nectivity.

4Verify that the Power LED on the external enclosure is a

steady green.

STEP 2: PREPARE YOUR COMPUTER FOR AP

SETUP

1On your Windows 7 computer, configure your network

adapter from the Local Area Connection settings as follows:

•Start > Control Panel > Network and Sharing

Center > Change Adapter Settings

2Edit the TCP/IPv4 address settings as follows:

•Local Area Connection > Properties > Internet

Protocol Version 4 (TCP/IPv4) > Properties

The TCP/IPv4 Properties dialog box appears.

3Select Use the following IP address (if it is not already

selected) and then make the following entries:

•IP address: 192.168.0.22 (or any address in the

192.168.0.x network)

•Subnet mask: 255.255.255.0

•Default gateway: 192.168.0.1

Leave the DNS server fields empty.

4Click OK to save your changes.

Your changes are put into effect immediately.

S TEP 3: LOG INTO THE AP

As specified earlier, the AP should be directly connected to your

computer (through the Ethernet port) and powered on, ready for

setup.

1On your computer, open a Web browser window.

2In the browser, type this URL to connect to the AP:

https://192.168.0.1

3Press <Enter> to initiate the connection. When a security

alert dialog box appears, click OK/Yes to proceed.

4When the Ruckus Wireless Admin login page appears, enter

the following:

•Username: super

•Password: sp-admin

5Click Login.

IMPORTANT!

If the AP is deployed with a ZoneDirector, follow the

ZoneDirector Quick Setup Guide, and connect the AP to your

local network.

NOTE:

The following procedures assume Windows 7 as the operating

system. Procedures for other OS’s are similar.

IMPORTANT!

Write down all of the currently active settings so you can

restore your computer to its current configuration later (when

this process is complete).

Published January 2013, Part Number 800-70415-001 Rev E

S TEP 4: CUSTOMIZE THE W SIRELESS ETTINGS

1On the Web interface menu, click Configuration > Wire-

less (Configuration > Radio 2.4G or Configuration > Radio

5G for the ZoneFlex 7372). The Configure :: Wireless :: Com-

mon options appear.

2Verify that the following options are active:

•Channel: SmartSelect

•Country Code: If you are not located in the United

States, select your current country.

3Click Update Settings if you made any changes.

4Click any of the eight “Wireless #” tabs at the top of the

page.

5In Wireless Availability, click Enabled.

6Delete the text in the SSID field, and then type a name for

your network that will help your users identify the AP in their

wireless network connection application.

7Click Update Settings to save your changes.

8Repeat Steps 4-7 for each Wireless # interface that you want

to enable.

9Click Logout to exit the Web interface.

10 Disconnect the AP from the computer and from the current

power source, and then restore your computer to its original

network connection configuration.

S TEP 5: PLACE THE AP IN YOUR SITE

1Move the AP to its permanent location (accessible to both

AC power and network connection).

2Use an Ethernet cable to connect the 10/100/1000 port of

the AP to your network.

3Connect the AC power adapter (or PoE power supply) to the

AP, then to a convenient power source.

4Verify that the 10/100/1000 port LED is lit.

After a short pause to re-establish the Internet connection, you

can test the AP.

STEP 6: VERIFY THE INSTALLATION

1Using any wireless-enabled computer or mobile device,

search for and select the wireless network you previously

configured.

2If you can connect, open a browser and link to any public

Web site.

Congratulations! Your wireless network is active and ready for

use.

(O IPTIONAL) MOUNTING NSTRUCTIONS

The ZoneFlex 7352/7372 can be mounted to a wall, ceiling or to

a T-bar using the supplied mounting screws or the T-bar clips

built into the bottom of the AP enclosure.

Mounting to a Flat Surface

1Use this Quick Start Guide template or the alignment spacer

to mark the locations for screw holes on the mounting sur-

face. Use a 5mm drill bit to drill approximately 25mm into

the mounting surface.

2Insert the anchors and mounting screws into the mounting

surface, leaving approximately 0.28” (7 mm) of the screw

heads protruding for the AP enclosure.

The screws should be approximately 3.25” (82.6 mm) apart

per the template.

3Insert a straightened paperclip (or similar) into the hole on

the side of the AP (Figure 1.), to release the locking mecha-

nism.

Figure 1. Insert a paperclip into the pinhole

4Place the AP onto the mounting screws so that the screw

heads enter the mounting holes on the AP enclosure, and

push the AP downward to lock in place.

5Remove the paperclip to release the lock mechanism and

secure the AP.

6To unmount, insert a straightened paperclip into the hole on

the side of the AP to unlock, then push the AP upward to

release the AP enclosure from the mounting screws.

Mounting to a T-Bar

The ZoneFlex 7352/7372 provides mounting options for flush tile

and recessed frame T-bars in acoustical ceiling tiles.

Flush Tile

1Orient the AP so that the T-bar is positioned between the T-

bar clips as shown in Figure 2., then rotate the AP until the

third T-bar clip catches the T-bar and the latch locks the T-bar

in place (Figure 3.).

Figure 2.

Figure 3.

Default AP Settings (For Your Reference)

Network Names

(SSIDs)

Wireless1—Wireless8 (2.4GHz radio)

Wireless9—Wireless16 (5GHz radio,

ZoneFlex 7372 only)

Security (Encryption

method)

Disabled for each wireless interface

Default Management

IP Address

192.168.0.1

NOTE:

If you will be using PoE, you will need a Cat5e (or better)

Ethernet cable to connect the AP to the PoE injector or switch.

Hold paperclip in

while mounting

Security screw

hole

Published January 2013, Part Number 800-70415-001 Rev E

2Insert the Torx-head security screw into the hole near the

latch to lock in place.

3To remove the unit, first remove the security screw, then

depress the latch while rotating the AP so that the T-bar clips

disengage the T-bar.

Recessed Frame

The enclosed T-bar clips support mounting to recessed frame

drop ceiling T-bars.

1Fasten T-Bar clips (included) to the T-Bar.

2Twist the two T-bar clips onto the acoustical ceiling T-bar.

Adjust the height of the anchor sleeves such that the anchor

heads extend just below the ceiling tile surface. Anchor

sleeves can be adjusted to accommodate frame recess

depths up to 6mm.

3Clip the alignment spacer between the two T-bar clip/anchor

sleeve assemblies.

4Insert a straightened paperclip (or similar) into the pinhole

on the side of the AP and hold in place while mounting (see

Figure 4.).

5Place the AP over the anchor sleeves such that the heads

enter the mounting holes on the AP enclosure, and slide the

AP to lock in place.

6Remove the paperclip to release the lock mechanism and

secure the AP.

7To remove the AP, insert a straightened paperclip into the

hole on the side of the AP to unlock, and then slide the AP

to release the AP enclosure from the mounting screws.

Figure 4. Recessed frame T-bar mounting

FOR MORE INFORMATION

You can now use the wireless network to log into the AP’s Web

interface. Use the Web interface to review and fine-tune a wide

range of AP settings. For information on how to configure the AP

from the Web interface, refer to the Ruckus Wireless ZoneFlex

Indoor Access Point User Guide or the Online Help, available

from within the Web interface.

NOTE:

If the T-bar clips slide easily along the T-bar, use a piece of

Scotch tape or similar to secure them in place while mounting

the AP. The tape may be removed once the AP is mounted.

Hold paperclip in

while mounting

Product specificaties

Merk:	Ruckus Wireless
Categorie:	Access point
Model:	ZoneFlex 7372
Gewicht:	350 g
Breedte:	158 mm
Diepte:	158 mm
Hoogte:	40 mm
Frequentieband:	2.4 - 2.484 GHz
Aantal Ethernet LAN (RJ-45)-poorten:	2
Aansluiting voor netstroomadapter:	Ja
Netwerkstandaard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Ondersteunde beveiligingsalgoritmen:	802.1x RADIUS, WEP, WPA-PSK, WPA-TKIP, WPA2-AES
Aantal gebruikers:	- gebruiker(s)
Intern:	Nee
Draadloos LAN data-overdrachtsnelheid (max):	300 Mbit/s
Maximale overdrachtssnelheid van gegevens:	300 Mbit/s
2,4 GHz:	Ja
Kanaalbandbreedte:	20 MHz
Power over Ethernet (PoE):	Ja
Aantal kanalen:	13 kanalen
Beheerprotocollen:	HTTP/S, CLI (Telnet/SSH), SNMP v1, 2, 3
Stroomverbruik (typisch):	3.2 W
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 95 procent