Rossmax ThermoCal - Professional Testing Device for Handleiding

Rossmax Thermometer ThermoCal - Professional Testing Device for

Lees hieronder de 📖 handleiding in het Nederlandse voor Rossmax ThermoCal - Professional Testing Device for (2 pagina's) in de categorie Thermometer. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Instruction Manual
Model: ThermoCal
Professional Testing Device
for Thermometer
www.rossmax.com
OBM_IB_ThermoCal_ver1411
Manufacturer: Rossmax Swiss GmbH,
Tramstrasse 16, CH-9442 Berneck, Switzerland
2. Heating indicator of the water bath does not light up after the calibration temperature is set
Possible causes Actions to take
Water temperature is higher than the set
temperature Cool down the water in the bath
Defective heating indicator Contact Rossmax for service
Defective temperature controller Contact Rossmax for service
Set temperature is too low Set temperature should be at least 5°C higher
than operating temperature
3. Heating indicator of water bath lights up, whereas the water temperature remains low
Possible causes Actions to take
Defective heater circuit Contact Rossmax for service
Defective temperature controller Contact Rossmax for service
4. Water temperature continues to rise and exceed the set temperature
Possible causes Actions to take
Defective temperature controller Contact Rossmax for service
5. Large uctuation in water temperature
Possible causes Actions to take
Water temperature is not stable yet Wait for temperature to stabilize
Set temperature is too close to ambient
temperature Lower the ambient temperature
Defective temperature controller Contact Rossmax for service
Defective water heater Contact Rossmax for service
6. Power and power indicator are both on, whereas the water circulating pump does not start
Possible causes Actions to take
Foreign object clogs inside the pump Remove the foreign object
Loose screw used to secure the propeller Tighten the screw
Defective motor Contact Rossmax for service
7. Noise generated by the stirrer motor
Possible causes Actions to take
Bearing ball oxidation Replace bearing
Bearing aging Replace bearing
Trouble shooting
1. Power is switched on but the power indicator does not light up
Possible causes Actions to take
No power input Check the power source
Loose plug Insert the plug into the socket securely
Device is powered and running but the power
indicator does not light up Replace the power switch
Power wire broke or loose connection Replace the power wire(s)
Tripped fuse Check the fuse and replace it if needed
WARNING: The symbol on this product means that it’s an
electronic product and following the European directive
2012/19/EU the electronic products have to be disposed
on your local recycling centre for safe treatment.
Accuracy is always the biggest concern of a thermometer user. Rossmax ThermoCal is a portable
and convenient device that allows the user to easily check the accuracy of a thermometer in just a
few seconds. The innovative design of the adjustable blackbody cavity applies to all three types of
Rossmax thermometer products - pen type, ear and forehead thermometer.
Parts name/location
Control panel Back view
Introduction
Instructions for installation
Cautions and maintenance
Specications
Operation procedures
1. Check the accuracy
Step 1: Check water level of the bath.
Step 2: Turn on the device.
Step 3: Select a testing temperature on the control panel (default at 37°C).
Step 4: Wait for the water to reach the desired temperature.
Step 5: Choose the blackbody cavity corresponding to the thermometer types.
Step 6: Set the thermometer into the calibration mode.
Step 7: Insert the probe/tip into the cavity.
Step 8: Start the measurement.
Step 9: Thermometer will beep when the measurement is completed.
Step 10: Compare the reading given by the thermometer to the calibration temperature.
The acceptable allowance is within ±0.2°C.
2. Drain the water bath
Step 1: Make sure the device is off.
Step 2: Remove the tube from the upper end.
Step 3: Empty the water bath by lowering the upper end of the tube.
Step 4: Plug the tube back in after the draining is completed.
1. Install the device on a solid surface.
2. Make sure the power is off before plugging in the device.
3. Keep the device away from the environment with direct sunlight, high temperature, high
humidity or severe change in temperature.
4. Make sure the AC power and its grounding plug are properly connected.
5. Do not use power extension cords.
6. Use pure water or distilled water only for the water bath to avoid contamination or water
heater breakdown.
7. Pay attention to the water level to avoid overspill.
8. The water bath is to remain 90% full at all times to reach water temperature stability.
1. Make sure the device, AC power and its grounding plug, is plugged in properly.
2. Change water periodically, once a month is suggested.
3. Use pure water or distilled water only for the water bath. Other water sources might increase
the chance of calcium carbonate formation on the outside of the water heater.
4. Make sure there is enough water in the water bath every time before using the device. Please
constantly pay attention to the water level and hygiene when/if the device runs for over 6 hours
or the water temperature exceeds 40°C.
5. Keep the device away from physical impact.
6. Unplug the device and empty the water bath if the device is going to be inactive for a long
time.
7. Unplug the device before moving it or draining the water bath.
8. Clean the water bath with a 3M scrub sponge if any signs of iron oxidization appear.
9. Pay attention to the water temperature to avoid scald.
Power source AC 100-240V 50/60 Hz
Power of water heater 255W
Testing temperature Ambient temperature + 5°C to maximum 45°C
Ambient temperature 16 ~ 30°C
Stability of water bath temperature ± 0.02°C
Diameter of
blackbody cavity
Pen type 15 mm
Ear 12.5 mm
Forehead 55 mm
Capacity 5.39 Liters
Weight 9.69 kgs
Dimension 180(W) x 350(H) x 320(D) mm
Control
panel
Ventilation
holes
Water
bath actual
temperature
Water bath set
temperature
Heating
indicator
Temperature up
Temperature down
Digit selecting key
Temperature setting key
Socket
and fuse
Power
switch
Cooling
fan
Overheating
protection
setting knob
Drain
tube
Removable
bath cover Blackbody
cavity
Computer

Product specificaties

Merk: Rossmax
Categorie: Thermometer
Model: ThermoCal - Professional Testing Device for

Heb je hulp nodig?

Als je hulp nodig hebt met Rossmax ThermoCal - Professional Testing Device for stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Thermometer Rossmax

Rossmax

Rossmax ThermoCal Handleiding

28 Maart 2024
Rossmax

Rossmax TG120 Handleiding

19 Maart 2024
Rossmax

Rossmax TG100 Handleiding

19 Maart 2024
Rossmax

Rossmax HC700 Handleiding

11 Februari 2023
Rossmax

Rossmax TG380 Handleiding

11 Februari 2023
Rossmax

Rossmax RA600 Handleiding

11 Februari 2023
Rossmax

Rossmax HA500 Handleiding

11 Februari 2023
Rossmax

Rossmax ThermoCal - Professional Testing Device for Handleiding

11 Februari 2023

Handleiding Thermometer

Nieuwste handleidingen voor Thermometer

Owon

Owon TI219 Handleiding

21 December 2024
TFA

TFA 12.1004 Handleiding

21 December 2024
Optex

Optex PT-U80 Handleiding

16 December 2024
Optex

Optex PT-7LD Handleiding

16 December 2024
Ebro

Ebro TFI 260 Handleiding

15 December 2024
Ebro

Ebro TFI 54 Handleiding

15 December 2024
EMOS

EMOS E0522 Handleiding

13 December 2024
Senseca

Senseca PRO 111 Handleiding

11 December 2024
TFA

TFA Spira 30.3064 Handleiding

7 December 2024
TFA

TFA Base 30.3061 Handleiding

7 December 2024