Rikon 70-150VSR Handleiding

Rikon Niet gecategoriseerd 70-150VSR

Lees hieronder de đź“– handleiding in het Nederlandse voor Rikon 70-150VSR (24 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/24
www.rikontools.com
70-150VSRM2
12 x 16-1/2 Midi VSR Lathe ” ”
Operator’s Manual
Record the serial number and date of purchase in your manual for future reference.
Serial Number: _________________________ Date of purchase: _________________________
For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877) 884-5167
The serial number can be found on the speciîšżcation label on the rear of your machine.
70-150VSR
2
TABLE OF CONTENTS
SPECIFICATIONS 70-150VSR
NOTE: The speciîšżcations, photographs, drawings and information in this manual represent the current model
when the manual was prepared. Changes and improvements may be made at any time, with no obligation on
the part of RIKON POWER TOOLS to modify previously delivered units. Reasonable care has been taken to ®
ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety,
assembly and operation of this machine.
Motor ........................................................................................... 1 HP, DC, TEFC
Motor Speed (no load).......................................................................... 3,200 RPM
Volts, Phase ........................................................................................ 115 V, 1 Ph
Amps, Hertz .......................................................................................... 6 A, 60 Hz
Swing Over Bed ............................................................................... 12” (305 mm)
Swing Over Tool Rest Base.......................................................... 9-1/4” (235 mm)
Distance Between Centers......................................................... 16-1/2” (419 mm)
Electronic Variable Speeds ........................................................ 250 - 3,200 RPM
Speed Ranges (3) ..................................... 250-850 / 430-1,450 / 950-3,200 RPM
Spindle Rotation (2) ..................... Forward (C-Clockwise) & Reverse (Clockwise)
Spindle Nose Threading.......................................................................... 1” x 8 TPI
Headstock Taper ............................................................................................ MT-2
Tailstock Taper ............................................................................................... MT-2
Hole Through Drive Spindle .............................................................. 3/8” (10 mm)
Hole Through Tailstock ...................................................................... 3/8” (10 mm)
Tailstock Ram Travel ...................................................................... 3-1/2" (90 mm)
Number of Indexing Positions............................................................................. 24
Tool Rest Post Diameter ....................................................................1” (25.4 mm)
Overall Size (LxWxH)......................39” x 13-3/8" x 15-5/8" (991 x 340 x 397 mm)
Cast Base Size (LxW) ................................ 31-13/16” x 7-7/32” (808 x 183.5 mm)
Net Weight ....................................................................................... 95 lbs (43 kg)
Speciîšżcations.....................................................................................................................2
Safety Instructions ........................................................................................................3 - 6
Contents of Package .....................................................................................................7
Getting To Know Your Machine ..............................................................................................8
Installation ......................................................................................................................8
Assembly ................................................................................................................................... 8
Operation .................................................................................................................. 9 - 11
Adjustments............................................................................................................... 12 - 14
Maintenance .................................................................................................................... 15
Troubleshooting ..........................................................................................................15 - 16
Parts Diagram & Parts List ..................................................................................... 17 - 20
Electricals & Wiring Diagram .....................................................................................5 & 21
Accessories ........................................................................................................ 21 & 22
Notes ........................................................................................................ 15 & 22
Warranty .......................................................................................................................... 23
3
SAFETY SYMBOLS
IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following
instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock,
îšżre, and/or serious personal injury.
There are certain applications for which this tool was designed. We strongly recommend that this tool not be modiîšżed
and/or used for any other application other than that for which it was designed. If you have any questions about its
application, do not use the tool until you have contacted us and we have advised you.
SAFETY INSTRUCTIONS
GENERAL SAFETY
KNOW YOUR POWER TOOL. Read the owner’s manual
carefully. Learn the tool’s applications, work capabilities,
and its speciîšżc potential hazards.
BEFORE USING YOUR MACHINE
To avoid serious injury and damage to the tool, read and
follow all of the Safety and Operating Instructions before
operating the machine.
1. Some dust created by using power tools
contains chemicals known to the State of California to
cause cancer, birth defects, or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and other
• masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area and work
with approved safety equipment, such as those dust masks
that are specially designed to îšżlter out microscopic
particles.
2. the entire Owner’s Manual. how to use READ LEARN
the tool for its intended applications.
3. If the tool is supplied with a 3 GROUND ALL TOOLS.
prong plug, it must be plugged into a 3-contact electrical
receptacle. The 3rd prong is used to ground the tool and
provide protection against accidental electric shock. DO
NOT remove the 3rd prong. See Grounding Instructions
on the following pages.
4. AVOID A DANGEROUS WORKING ENVIRONMENT.
DO NOT use electrical tools in a damp environment or
expose them to rain.
5. use electrical tools in the presence of DO NOT
ammable liquids or gasses.
6. ALWAYS keep the work area clean, well lit, and
organized. work in an environment with oor DO NOT
surfaces that are slippery from debris, grease, and wax.
7. KEEP VISITORS AND CHILDREN AWAY. DO NOT
permit people to be in the immediate work area,
especially when the electrical tool is operating.
8. to perform an operation DO NOT FORCE THE TOOL
for which it was not designed. It will do a safer and
higher quality job by only performing operations for
which the tool was intended.
9. wear loose WEAR PROPER CLOTHING. DO NOT
clothing, gloves, neckties, or jewelry. These items can
get caught in the machine during operations and pull the
operator into the moving parts. The user must wear a
protective cover on their hair, if the hair is long, to
prevent it from contacting any moving parts.
10. CHILDPROOF THE WORKSHOP AREA by
removing switch keys, unplugging tools from the
electrical receptacles, and using padlocks.
11. ALWAYS UNPLUG THE TOOL FROM THE
ELECTRICAL RECEPTACLE when making adjust-
ments, changing parts or performing any maintenance.
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. This symbol may be used
in conjunction with other symbols or pictographs.
Indicates an imminently hazardous situation, which, if not avoided, could result in death or
serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious
injury.
Indicates a potentially hazardous situation, which, if not avoided, could result in minor or
moderate injury.
NOTICE: Shown without Safety Alert Symbol indicates a situation that may result in property damage.

Product specificaties

Merk: Rikon
Categorie: Niet gecategoriseerd
Model: 70-150VSR

Heb je hulp nodig?

Als je hulp nodig hebt met Rikon 70-150VSR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Rikon

Rikon

Rikon 50-320 Handleiding

2 Oktober 2024
Rikon

Rikon 50-310 Handleiding

2 Oktober 2024
Rikon

Rikon 50-1305 Handleiding

5 Augustus 2024
Rikon

Rikon 70-150VSR Handleiding

2 April 2024
Rikon

Rikon 70-1516VSR Handleiding

2 April 2024
Rikon

Rikon 70-3040 Handleiding

5 Maart 2024
Rikon

Rikon 70-1420VSR Handleiding

4 Maart 2024
Rikon

Rikon 60-2500 Handleiding

4 Maart 2024
Rikon

Rikon 70-1218VS Handleiding

4 Maart 2024
Rikon

Rikon 60-1750 Handleiding

4 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Inglesina

Inglesina Welcome Pad Handleiding

22 December 2024
Inglesina

Inglesina Front Handleiding

22 December 2024
Inglesina

Inglesina Newborn Winter Muff Handleiding

22 December 2024
Inglesina

Inglesina Stroller Winter Muff Handleiding

22 December 2024
Protector

Protector AS-5030.3 V2 Handleiding

21 December 2024
Sabrent

Sabrent AU-MMCW Handleiding

21 December 2024
Sabrent

Sabrent AU-2X35 Handleiding

21 December 2024
Sabrent

Sabrent CB-RS232 Handleiding

21 December 2024
Owon

Owon 500W Handleiding

21 December 2024
Owon

Owon 300W Handleiding

21 December 2024