Rikon 11-600S Handleiding

Rikon Zaagmachine 11-600S

Lees hieronder de 📖 handleiding in het Nederlandse voor Rikon 11-600S (28 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

11-600S

10 Portable Table Saw w/Stand”

www.rikontools.com

11-600SM1

Operator’s Manual

Record the serial number and date of purchase in your manual for future reference.

Serial Number: _________________________ Date of purchase: _________________________

For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167

SAFETY RULES

WARNING: For your own safety, read all of the instructions and

precautions before operating tool.

PROPOSITION 65 WARNING: Some dust created by

using power tools contain chemicals known to the state of

California to cause cancer, birth defects or other reproductive

harm.

Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks and cement and other

masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures vary, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area and work with approved safety

equipment. Always wear OSHA/NIOSH approved, properly tting

face mask or respirator when using

such tools.

CAUTION: Always follow proper operating procedures as

dened in this manual — even if you are familiar with use of

this or similar tools. Remember that being careless for even a

fraction of a second can result in severe personal injury.

BE PREPARED FOR THE JOB

• Wear proper apparel. Do not wear loose clothing, gloves,

neckties, rings, bracelets or other jewelry which may get

caught in moving parts of machine.

• Wear protective hair covering to contain long hair.

• Wear safety shoes with non-slip soles.

• Wear face mask or dust mask if operation is dusty.

TABLE OF CONTENTS

Safety Rules..

...............................................................................2-5

Unpacking.......................................................................................5

Assembly......................................................................................6-9

Installation & Specications...

.....................................................9-10

Operation..

...............................................................................10-13

Adjustments.............................................................................14-15

Maintenance.................................................................................15

Troubleshooting............................................................................16

Parts Diagrams & Lists............................................................17-27

Warranty.......................................................................................27

• Wear safety glasses complying with United States ANSI

Z87.1. Everyday glasses have only impact resistant lenses.

They are safety glasses. NOT

• Be alert and think clearly. Never operate power tools

when tired, intoxicated or when taking medications

that cause drowsiness.

PREPARE WORK AREA FOR JOB

• Keep work area clean. Cluttered work areas invite

accidents.

• Do not use power tools in dangerous environments. Do not

use power tools in damp or wet locations. Do not expose

power tools to rain.

• Work area should be properly lighted.

• Keep visitors at a safe distance from work area.

• Keep children out of workplace. Make workshop childproof.

Use padlocks, master switches or remove switch keys to

prevent any unintentional use of power tools.

• Keep power cords from coming in contact with sharp

objects, oil, grease and hot surfaces.

TOOL SHOULD BE MAINTAINED

• Always unplug tool prior to inspection.

• Consult manual for specic maintaining and adjusting

procedures.

• Keep tool lubricated and clean for safest operation.

• Remove adjusting tools. Form habit of checking to see that

adjusting tools are removed before switching machine on.

• Keep all parts in working order. Check to determine that

the guard or other parts will operate properly and perform

their intended function.

• Check for damaged parts. Check for alignment of moving

parts, binding, breakage, mounting and any other condition

that may a󰀨ect a tool’s operation.

• A guard or other part that is damaged should be properly

repaired or replaced. Do not perform makeshift repairs.

(Use parts list provided to order replacement parts.)

• Maintain proper adjustment of rip fence and blade guard.

• Never adjust saw while running. Disconnect power to avoid

accidental start-up.

• Have damaged or worn power cords replaced immediately.

• Keep blade sharp for e󰀩cient and safest operation.

KNOW HOW TO USE THE TOOL

• Use right tool for the job. Do not force tool or attachment to

do a job for which it was not designed.

• Disconnect tool when changing blade.

• Avoid accidental start-up. Make sure that the tool is in the

“o󰀨” position before plugging in, turning on safety

disconnect or activating breakers.

• Do not force tool. It will work most e󰀩ciently at the rate for

which it was designed.

• Keep hands away from blade and moving parts and cutting

surfaces.

• Never leave tool running unattended. Turn the power o󰀨

and do not leave tool until it comes to a complete stop.

• Do not overreach. Keep proper footing and balance.

• Never stand on tool. Serious injury could occur if tool is

tipped or if blade is unintentionally contacted.

• Know your tool. Learn the tool’s operation, application and

specic limitations.

• Handle workpiece correctly. Press rmly against table.

Protect hands from possible injury.

• Turn machine o󰀨 if it jams. Blade jams when it digs too

deeply into workpiece. (Motor force keeps it stuck in the

work.)

• Feed work into the blade only as recommended in

“Operation.”

WARNING: For your own safety, do not operate your saw

until it is completely assembled and installed according to

instructions.

STABILITY OF SAW

If there is any tendency for the saw to tip over or move during

certain cutting operations, such as cutting extremely heavy

panels or long heavy boards, the saw should be bolted down.

If you attach any kind of extensions over 24" wide to either

end of the saw, make sure you support the outer end of the

extension from the bench or oor, as appropriate.

LOCATION

The saw should be positioned so neither the operator nor a

casual observer is forced to stand in line with the saw blade.

KICKBACKS

A kickback occurs during a rip-type operation when a part or

all of workpiece is thrown back violently toward operator.

Keep your face and body to one side of the saw blade, out of

line with a possible kickback.

Kickbacks and possible injury from them can usually be

avoided by:

• Maintaining rip fence parallel to saw blade.

• Keeping saw blade sharp. Replace or sharpen anti-

kickback pawls when points become dull.

• Keeping saw blade guard, spreader, and anti-kickback

pawls in place and operating properly. The spreader must

be in alignment with the saw blade and the pawls must

stop a kickback once it has started. Check their action

before ripping.

• Not ripping work that is twisted or warped or does not

have a straight edge to guide along the rip fence.

• Not releasing work until you have pushed it all the way

past the saw blade.

• Using a push stick for ripping widths less than 6 inches.

• Not conning the cuto󰀨 piece when ripping or crosscutting.

PROTECTION: EYES, HANDS, FACE, BODY, EARS

• If any part of your saw is missing, malfunctioning, or has

been damaged or broken (such as the motor switch,

electronic controls, other operating control, a safety device

or power cord), cease operating immediately until the

particular part is properly repaired or replaced.

• Wear safety goggles that comply with United States ANSI

Z87.1 and a face shield or dust mask if operation is dusty.

Wear ear plugs or mu󰀨s during extended periods of

operation.

• Small loose pieces of wood or other objects that contact

the rear of the revolving blade can be thrown back at the

operator at excessive speed. This can usually be avoided

by keeping the guard and spreader in place for all

thru-sawing operations (sawing entirely thru work) and

by removing all loose pieces from the table with a long stick

of wood immediately after they are cut o󰀨.

• Use extra caution when the guard assembly is removed for

resawing, dadoing, or rabbeting—replace guard as soon

as that operation is completed.

• Never turn the saw ON before clearing the table of all

tools, wood scraps, etc., except the workpiece and related

feed or support devices for the operation planned.

• Never place your face or body in line with the cutting tool.

• Never place your ngers or hands in path of saw blade or

other cutting tool.

• For rip or rip-type cuts, the following end of a workpiece to

which a push stick or push board is applied must be

square (perpendicular to the fence) in order that feed

pressure applied to the workpiece by the push stick or

block does not cause the workpiece to come away from

the fence, and possibly cause a kickback.

• During rip and rip-type cuts, workpiece must be held down

on table and against fence with a push stick, push block,

or featherboards, as applicable (see Figures 1a and 1b,

page 4).

The push stick and push block examples shown on page

4 are useful for keeping hands and ngers away from saw

blade during ripping, rabbeting and dadoing. Apply down-

ward pressure and push workpiece through the cut and past

the blades. Several other congurations may be suitable for

safe operation.

Featherboards are used to keep the work in contact with the

rip fence or table during the cutting operation. Use of feather-

boards can help to prevent kickbacks and binding. Feather-

boards should be used for all “non thru-sawing” operations.

• Never reach in back of the cutting tool with either hand to

hold down or support the workpiece, remove wood scraps,

or for any other reason. Avoid awkward operations and

hand positions where a sudden slip could cause ngers or

hand to move into a saw blade or other cutting tool.

• Do not perform layout, assembly, or setup work on the

table while the cutting tool is rotating.

• Do not perform any operation freehand—always use either

rip fence or miter gauge to position and guide the work.

• Never use the rip fence when cross-cutting or the miter

gauge when ripping. Do not use rip fence as a length stop.

Never hold onto or touch free-end of workpiece or a free-

piece that is cut o󰀨, while power is ON and/or saw blade is

rotating.

• Shut the saw OFF and disconnect power source when

removing the table insert, changing the cutting tool,

removing or replacing the blade guard, or making adjust

ments.

• Provide adequate support to the rear and sides of the saw

table for wide or long workpieces.

• Plastic and composition materials (like hardboard) may be

cut on your saw. However, since these are usually quite

hard and slippery, the anti-kickback pawls may not stop a

kickback. Therefore, be especially attentive to following

proper setup and cutting procedures for ripping. Do not

stand, or permit anyone else to stand, in line with a poten-

tial kickback.

• If you stall or jam the saw blade in the workpiece, turn saw

OFF and remove the workpiece from the saw blade.

Check to see if the saw blade is parallel to the miter

gauge grooves and if the spreader is in proper alignment

with the saw blade. If ripping at the time, check to see if

the rip fence is parallel with the saw blade. Readjust as

required.

• Do not remove small pieces of cuto󰀨 material that may

become trapped inside the blade guard while the saw is

running. This could endanger your hands or cause kick

back. Turn saw OFF and wait until blade stops.

• Use extra care when ripping wood with twisted grain or

wood that is twisted or bowed—it may rock on table and

pinch saw blade.

Product specificaties

Merk:	Rikon
Categorie:	Zaagmachine
Model:	11-600S

Heb je hulp nodig?

Als je hulp nodig hebt met Rikon 11-600S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Rikon

Rikon 10-305 Handleiding

18 November 2024

Rikon 10-347 Handleiding

18 November 2024

Rikon 10-3061 Handleiding

18 November 2024

Rikon 11-600S Handleiding

18 November 2024

Rikon 10-205 Handleiding

18 November 2024

Rikon 10-342 Handleiding

18 November 2024

Rikon 10-353 Handleiding

18 November 2024

Rikon 10-600VS Handleiding

18 November 2024

Rikon 10-110 Handleiding

16 Maart 2024

Rikon 10-306 Handleiding

16 Maart 2024

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Alpha Tools BSL 750 Handleiding

17 November 2024

Alpha Tools PS 600 E Handleiding

17 November 2024

Alpha Tools MHK 500 Handleiding

17 November 2024

Alpha Tools PS 520E Handleiding

17 November 2024

Pro-Cut KS-120 Handleiding

17 November 2024

Global KS 2040 Handleiding

17 November 2024

Anova MG2600 Handleiding

17 November 2024

Anova M437HXP Handleiding

17 November 2024

Anova RLT8C Handleiding

17 November 2024

Anova M455HXP Handleiding

17 November 2024