Qubino ZMNHBA2 power relay Handleiding

Qubino Niet gecategoriseerd ZMNHBA2 power relay

Lees hieronder de 📖 handleiding in het Nederlandse voor Qubino ZMNHBA2 power relay (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Qubino

The INNOVATIVE SMALLEST and

Flush 2 relays

ORDERING CODE

Z-WAVE FREQUENCY

ZMNHBA2

868,4 MHz

ZMNHBA3

921,4 MHz

ZMNHBA4

908,4 MHz

ZMNHBA5

869,0 MHz

ZMNHBA6

916,0 MHz

This Z-Wave module is used for switching on or

oﬀ two electrical devices (e.g. lights, fans, etc ...).

The module can be controlled either through

Z-Wave network or through the wall switches.

The module is designed to be mounted inside a

“ ”ﬂush mounting box , hidden behind a traditional

wall switch.

Module measures power consumption of two

electrical devices and supports connection of

digital temperature sensor. It is designed to act

as repeater in order to improve range and

stability of Z-wave network.

Supported switches

Module supports switches (push mono-stable

button) and switches. The module is bi-stable

factory set to operate with bi-stable switches.

Installation

 Before the installation disconnect power

supply.

 Connect the module according to electrical

diagram.

 Locate the antenna far from metal elements

(as far as possible).

 Do not shorten the antenna.

Danger of electrocution!

 Module installation requires a great degree of

skill and may be performed only by a qualiﬁed

and licensed electrician.

 Even when the module is turned oﬀ, voltage

may be present on its terminals. Any works

on conﬁguration changes related to

connection mode or load must be always

performed by disconnected power supply

(disable the fuse).

Note!

Do not connect the module to loads exceeding

recommended values. Connect the module only

in accordance to the below diagrams. Improper

connections may be dangerous.

Package contents

 Flush 2 relays

Electrical diagram 230VAC

Notes for the diagram:

Electrical diagram 24VDC

Notes for the diagram:

Durability of the device depends on applied load.

For resistive load (light bulbs, etc.) and 4A

current consumption of each individual electrical

device, the durability exceeds 70.000 switches of

each individual electrical device.

Module Inclusion (Adding to Z-Wave

network)

 Connect module to power supply (with

temperature sensor connected - if

purchased),

 bring module within maximum 1 meter (3

feet) of the main controller,

 enable add/remove mode on main controller,

 auto-inclusion (30 minutes after connected

to power supply) or

 press service button for more than 2 S

second or

 press push button three times within 3s I1

(3 times change switch state within 3

seconds)

Module Exclusion/Reset (Removing

from Z-Wave network)

 Connect module to power supply

 bring module within maximum 1 meter (3

feet) of the main controller,

 enable add/remove mode on main controller,

 press service button for more than 6 S

second or

 press push button ﬁve times within 3s (5 I1

times change switch state within 3 seconds)

in the ﬁrst 60 seconds after the module is

connected to the power supply.

By this function all parameters of the module are

set to default values and own ID is deleted.

If service button S is pressed more than 2 and

less than 6second module is excluded, but

conﬁguration parameters are not set to default

values

Association

Association enables Flush 2 relays module to

transfer commands inside Z-Wave network

directly (without main controller) to other Z-Wave

modules.

Associated Groups:

Group 1: basic on/oﬀ (triggered at change of the

output Q1 state and reﬂecting its state) up to 16

nodes.

Group 2: basic on/oﬀ (triggered at change of the

output Q2 state and reﬂecting its state) up to 16

nodes.

Group 3: default reporting group (reserved for the

main controller).

Conﬁguration parameters

Parameter no. Input 1 switch type 1 –

Available conﬁguration parameters (data type is

1 Byte DEC):

 default value 1

 mono-stable switch type (push button) 0

 -stable switch type 1 bi

Parameter no. 2 Input 2 switch type –

Available conﬁguration parameters (data type is

1 Byte DEC):

 default value 1

 mono-stable switch type (push button) 0

 -stable switch type 1 bi

Parameter no. 10 - Activate / deactivate

functions ALL ON/ALL OFF

Available conﬁguration parameters (data type is

1 Byte DEC):

 default value 255

 255 - ALL ON active, ALL OFF active.

 - ALL ON is not active ALL OFF is not 0

active

 - ALL ON is not active ALL OFF active 1

 - ALL ON active ALL OFF is not active 2

On/Oﬀ module responds to commands ALL ON /

ALL OFF that may be sent by the main controller

or by other controller belonging to the system.

Parameter no. 11 - Automatic turning Oﬀ relay

Q1 after set time

Available conﬁguration parameters (data type is

2 Byte DEC):

 Default value 0

 - Auto OFF disabled 0

 1- 65535 = 10mseconds 655,35 seconds–.

Auto OFF enabled, with deﬁne time, step is

10mseconds.

Parameter no. 12 - Automatic turning Oﬀ relay

Q2 after set time

Available conﬁguration parameters (data type is

2 Byte DEC):

 Default value 0

 - Auto OFF disabled 0

 1- 65535 = 10mseconds 655,35 seconds. –

Auto OFF enabled, with deﬁne time, step is

10mseconds.

Parameter no. 30 - Saving the state of the

relays Q1 and Q2 after a power failure

Available conﬁguration parameters (data type is

1 Byte DEC):

 default value 0

 Flush 2 relays module saves its state 0 –

before power failure (it returns to the last

position saved before a power failure)

 - Flush 2 relays module does not save the 1

state after a er failure, it returns to "oﬀ" pow

position.

Parameter no. 40 Power reporting in Watts –

on power change for Q1

Set value means percentage, set value from 0 –

+VDC

-VDC

Output for electrical device no. 1

Output for electrical device no. 2

Input for switch to control electrical

device no.2

Input for switch to control electrical

device no.1

Terminal for digital temperature sensor

(only for Flush 2 relays module

compatible digital temperature sensor,

which must be ordered separately).

Neutral lead

Live lead

Output for electrical device no. 1

Output for electrical device no. 2

Input for switch to control electrical

device no.2

Input for switch to control electrical

device no.1

Terminal for digital temperature sensor

(only for Flush 2 relays module

compatible digital temperature sensor,

which must be ordered separately).

Service button (used to

add or remove module

from the Z-Wave

network).

100 = 0% - 100% Available conﬁguration .

parameters (data type is 1 Byte DEC):

 default value 1

 Reporting Disabled 0 –

 100 = 1% - 100% Reporting enabled. 1 –

Power report is send (push) only when

actual power in Watts in real time changes

for more than set percentage comparing to

previous actual power in Watts, step is 1%.

NOTE: if power changed is less than 1W, the

report is no send (pushed), independent of t

percentage set.

Parameter no. 41 Power reporting in Watts –

on power change for Q2

Set value means percentage, set value from 0 –

100 = 0% - 100% Available conﬁguration .

parameters (data type is 1 Byte DEC):

 default value 1

 Reporting Disabled 0 –

 100 = 1% - 100% Reporting enabled. 1 –

Power report is send (push) only when

actual power in Watts in real time changes

for more than set percentage comparing to

previous actual power in Watts, step is 1%.

NOTE: if power changed is less than 1W, the

report is not send (pushed), independent of

percentage set.

Parameter no. 42 Power reporting in Watts –

by time interval for Q1

Set value means time interval (0 65535) in –

seconds, when power report is send. Available

conﬁguration parameters (data type is 2 Byte

DEC):

 default value 300 (power report in Watts is

send each 300s)

 Reporting Disabled 0 –

 65535 = 1 second 65535 seconds. 1 – –

Reporting enabled, Power report is send

with time interval set by entered value.

Parameter no. 43 Power reporting in Watts –

by time interval for Q2

Set value means time interval (0 65535) in –

seconds, when power report is send. Available

conﬁguration parameters (data type is 2 Byte

DEC):

 default value 300 (power report in Watts is

send each 300s)

 Reporting Disabled 0 –

 65535 = 1 second 65535 seconds. 1 – –

Reporting enabled, Power report is send

with time interval set by entered value.

Technical Speciﬁcations

Power supply

110 - 230 VAC ±10%

50/60Hz, 24-30VDC

Rated load current of AC

output (resistive load)*

2 X 4A / 230VAC

Rated load current of DC

output (resistive load)

2 X 4A / 30VDC

Output circuit power of

AC output (resistive

load)

2 X 920W (230VAC)

Output circuit power of

DC output (resistive

load)

2 X W (24VDC) 96

Power measurement

accuracy

P=0-200W, - +/ 2W

P>200W, - +/ 3%

Digital temperature

sensor range (sensor

must be ordered

separately)

- + 50 ~ 125°C

Operation temperature

-10 ~ + 40°C

Distance

up to 30 m indoors

(depending on

building materials)

Dimensions (WxHxD)

(package)

41,8x36,8x16,9mm

(79x x22) 52

Weight (Brutto with package)

28g (34g)

Electricity consumption

0,4W

For installation in boxes

Ø ≥ 60mm or 2M

Switching

Relay (2x)

*In case of load other than resistive, pay attention

to the value of cos φ and if necessary apply load

lower than the rated load. Max current for cos

φ=0,4 is 2A at 250VAC 3A at 24VDC.,

Z-Wave Device Class:

BASIC_TYPE_ROUTING_SLAVE

GENERIC_TYPE_SWITCH_BINARY

SPECIFIC_TYPE_POWER_SWITCH_BINARY

Z-Wave Supported Command Classes:

COMMAND_CLASS_BASIC

COMMAND_CLASS_SWITCH_BINARY

COMMAND_CLASS_MULTI_CHANNEL_V2

COMMAND_CLASS_SWITCH_ALL

COMMAND_CLASS_METER_V3

COMMAND_CLASS_SENSOR_MULTILEVEL_ V3

COMMAND_CLASS_POWERLEVEL

COMMAND_CLASS_ASSOCIATION

COMMAND_CLASS_CONFIGURATION

COMMAND_CLASS_MANUFACTURER_SPECIFIC

COMMAND_CLASS_VERSION

COMMAND_CLASS_MARK

COMMAND_CLASS_BASIC

Endpoint 1 (I1):

Device Class:

GENERIC_TYPE_SWITCH_BINARY

SPECIFIC_TYPE_POWER_SWITCH_BINARY

Command Classes:

COMMAND_CLASS_SWITCH_BINARY

COMMAND_CLASS_METER_V3

Endpoint 2 (I2):

Device Class:

GENERIC_TYPE_SWITCH_BINARY

SPECIFIC_TYPE_POWER_SWITCH_BINARY

Command Classes:

COMMAND_CLASS_SWITCH_BINARY

COMMAND_CLASS_METER_V3

This product can be included and operated in any

Z-Wave network with other Z-Wave certiﬁed

devices from any other manufacturers. All

constantly powered nodes in the same network

will act as repeaters regardless of the vendor in

order to increase reliability of the network.

Important disclaimer

Z-Wave wireless communication is inherently not

always 100% reliable, and as such, this product

should not be used in situations in which life

and/or valuables are solely dependent on its

function.

Warning!

Do not dispose of electrical appliances as

unsorted municipal waste, use separate

collection facilities.

Contact your local government for information

regarding the collection systems available. If

electrical appliances are disposed of in landﬁlls

or dumps, hazardous substances can leak into

the groundwater and get into the food chain,

damaging your health and well-being. When

replacing old appliances with new once, the

retailer is legally obligated to take back your old

appliance for disposal at least for free of charge.

This user manual is subject to change and

improvement without notice

Qubino

Goap d.o.o. Nova Gorica

Ulica Klementa Juga 007

5250 Solkan

Slovenia

E-mail: info@qubino.com

Tel: +386 5 335 95 00

Web: www.qubino.com

Date: .2.2015 20

Document: Qubino_Flush 2

relays user maual_V6 _eng .4

Product specificaties

Merk:	Qubino
Categorie:	Niet gecategoriseerd
Model:	ZMNHBA2 power relay
Kleur van het product:	Blauw
Gewicht:	28 g
Afmetingen (B x D x H):	41.8 x 15.4 x 36.8 mm
AC-ingangsspanning:	110-230 V
AC-ingangsfrequentie:	50 - 60 Hz
Aantal polen:	2
Aantal modules:	1