Presto EverSharp Profesional 08810 Handleiding
Presto
Messenslijper
EverSharp Profesional 08810
Lees hieronder de đź“– handleiding in het Nederlandse voor Presto EverSharp Profesional 08810 (4 pagina's) in de categorie Messenslijper. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
1
INSTRUCTIONS
Visit us on the web at www.GoPresto.com ©2018 National Presto Industries, Inc.
Estas instrucciones también están disponibles en español. Para obtener una copia impresa:
• Descargue en formato PDF en www.GoPresto.com/espanol.
• EnvĂe un correo electrĂłnico a contact@GoPresto.com.
• Llame al 1-800-877-0441, oprima 2 y deje un mensaje.
Professional EverSharp® three-stage electric knife sharpener
• Three-stage sharpening system provides professional results
at home.
• Blade selector adjusts guides to optimum sharpening angle
for thick, medium, and thin knives.
• Extra-fine grit ceramic wheel assures precision honing.
This is a Listed appliance. The following important safeguards are recommended by most portable appliance manufacturers.
IMPORTANT SAFEGUARDS
To reduce the risk of personal injury or property damage when using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions before using this appliance.
2. To protect against the risk of electrical shock, do not put the knife sharpener in water or other liquids.
3. This appliance is not intended for use by children or by persons with reduced physical, sensory, or mental capabilities, or lack of
experience and knowledge. Close supervision is necessary when any appliance is used near children. Children should be supervised
to ensure that they do not play with the appliance.
4. Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts, and before clean-
ing. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
5. Avoid contact with moving parts.
6. Do not operate any appliance with a damaged cord or plug, or in the event the appliance malfunctions, or is dropped or damaged
in any manner. Return the appliance to the Presto Factory Service Department for examination, repair, or electrical or mechanical
adjustment.
7. The use of accessory attachments not recommended or sold by the appliance manufacturer may cause fire, electric shock, or injury.
Use only genuine Presto™ accessory attachments and replacement parts.
8. Do not use outdoors.
9. Do not let the cord hang over edge of table or counter or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner or in a heated oven.
11. Do not use the knife sharpener for other than intended use.
12. Carefully route the power supply cord to avoid damage from the knife blades while sharpening.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY.
2
Important Cord Information
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit
into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to modify the plug in any way.
A short power supply cord is provided to reduce the risk of becoming entangled in or tripping over a longer cord. An extension cord may
be used if care is properly exercised in its use. If an extension cord is used, the marked electrical rating of the extension cord should be at
least as great as the electrical rating of the appliance. The extension cord should be arranged so that it will not drape over the countertop
or tabletop where it can be pulled on by children or tripped over unintentionally.
Connect the power supply cord to a 120VAC electrical outlet only.
Getting Acquainted
Your Presto® Professional EverSharp® electric knife sharpener is a three-stage sharpening system which will sharpen knives of alloy,
carbon, or stainless steel. It is designed to sharpen kitchen knives and most sporting knives.
Do not attempt to sharpen scissors, serrated electric knives, or any blade that does not fit freely in the blade guides.
If your knife is very dull, you will probably use all three stages. If a bit dull, use Stages 2 and 3. Frequently, you will use only Stage 3 to
maintain your knives in razor-sharp condition. The blade selector (Fig. A) adjusts the guides to an optimum sharpening angle for thick,
medium, and thin knives.
How to Use
1. Place the knife sharpener on a stable surface.
2. Determine the type of knife being sharpened and then move the blade selector to the appropriate position (Fig. A).
For thick knives, such as hunting knives and cleavers, move the blade selector to the top position.
For medium knives, such as utility, slicing, chef ’s, and Santoku knives, move the blade selector to the middle position.
For thin knives, such as fillet, paring knives, and other light blades, move the blade selector to the bottom position.
You will feel the stop points for each position. When you move the blade selector lever, the orange adjustable blade guides in Stages
2 and 3 will also move so they are at the optimum sharpening angle for the type of blade selected. In Stage 1, the blade guides are in
a fixed position.
3. Turn the unit ON by pressing the symbol “ ” on the ON/OFF switch (Fig. A). l
4. Evaluate the condition of your blade to determine with which sharpening stage to
start:
• If the blade is very dull, or if you are sharpening the knife for the first time, begin
with STAGE 1: GRINDING. This is the stage located to the left of the COARSE
ON/OFF switch. It is the coarsest and most aggressive stage, and will remove
more material from the knife blade than the other stages. It is a fixed stage with
no adjustments, as it places the same angle on all blades in preparation for the
sharpening stations found in Stages 2 and 3. Do not use Stage 1 when Note:
sharpening serrated blades.
• If your knife is a bit dull, begin with STAGE 2: PRECISION GRINDING. This is the
stage located directly to the right of the blade selector. It continues the grinding by giving
the blade a precision edge. It is an adjustable station, further refining the sharpening angle
so that when you are done, your knife is sharpened to the optimum angle dictated by the
width of the blade.
• If your knife just needs a little touch-up sharpening, begin with STAGE 3: FINE HONING.
This is the stage located on the far right and is the stage most frequently used. It is also
an adjustable station, completing the knife sharpening process by honing and polishing
the knife to an exact razor-sharp edge.
5. Begin sharpening. The sharpening procedure is the same for each stage.
Sharpening Procedure:
Begin by placing the heel of the knife in the left slot of the stage in use (Fig. B). The side
of the blade should rest against the outside face of the blade guide slot and the cutting edge
should make contact with the sharpening wheel (Fig. C).
Stage 1
(coarse grinding)
ON/OFF
switch
Fig. A
Stage 2
(precision grinding)
Stage 3
(fine honing)
Blade selector
Blade against outside face of left slot
Fig. B
Fig. C
Outside face
of left slot
Outside face
of right slot
3
CAUTION! Never insert the tip of the knife into the blade guide slots first and push through. This could damage the knife sharpener
and your knife.
Using only light downward pressure, slowly pull the knife straight toward you through the slot, except when sharpening the tip of
the blade. To sharpen the tip, lift up on the knife handle as the curved portion of the blade is drawn through the slots. NOTE: The
greater the curve on the blade, the more you will need to lift up on the handle. Certain blades may not have a curve and therefore it
will not be necessary to lift up on the handle as you draw the tip through the slots. If the motor slows while pulling the knife, apply
less downward pressure.
Draw the knife through the left and right slots three times, alternating passes between the two slots. Allow approximately one second
for each two inches of blade when drawing the knife through the slots. For example, if sharpening a knife with a 6-inch blade, you
should take approximately three seconds for each pass.
6. Before using the knife to slice food, always wipe the knife blade with a damp cloth to remove any metal filings that may have been
deposited during the sharpening process. CAUTION! To avoid injury, handle knives with extreme care.
7. If knife does not easily slice food, repeat Stages 2 and 3. Do not run fingers along edge of knife to check sharpness.
8. When sharpening is complete, turn the unit off by pressing the symbol “ ” on the OON/OFF switch. Metal filings may be present on
the table or countertop and may be wiped clean with a damp cloth.
Questions and Answers
How often should I sharpen my knives?
Use Stage 3 to hone the knife prior to each use if you want to maintain a razor-sharp edge. After extensive use, if you have honed the
knife and it no longer slices food with ease, run the knife through Stages 2 and 3.
How can I tell if my knife is sharp?
Use it to slice food. If it does not slice the food with ease, it needs additional sharpening. Repeat Stages 2 and 3. If the knife is extremely
dull, repeat Stages 1, 2, and 3. Do not run fingers along the edge of the knife to check sharpness.
How do I get an even edge on my knife?
To get an even edge when sharpening, be sure to place the knife in the slot so the side of the blade rests against the outside face of the
blade guide (Fig. B, page 2) and the cutting edge makes contact with the sharpening wheel (Fig. C, page 2) as you’re drawing the knife
through the slot. The outside face of each sharpening slot acts as a guide to insure that the knife is positioned at the perfect sharpening angle.
Allow adequate time for sharpening. When drawing the knife through the slots, allow approximately one second for each two inches of
blade. For example, if sharpening a knife with a 6-inch blade, you should take approximately three seconds for each pass. Pulling the
knife through too quickly may result in an uneven edge.
When sharpening the tip of the blade, lift up on the knife handle slightly as the curved portion of the blade is drawn through the blade
guides. Note: The greater the curve on the blade, the more you will need to lift up on the handle; the less the curve, the less you will
need to lift up on the handle. Certain blades may not have a curve and therefore it will not be necessary to lift up on the handle as you
draw the tip through the slots.
My knife is not sharp and I’ve gone through the whole knife sharpening procedure twice. What am I doing wrong?
Although unusual, there are times when you will have to repeat Stages 1, 2, and 3 more than once. This may occur during the first
sharpening of a knife that has been improperly sharpened by another process previously. It may also occur when sharpening knives of
tempered steel which have extremely hard blades, such as some hunting knives.
To sharpen these types of knives with this knife sharpener, simply continue to repeat Stages 1, 2, and 3 until the knife cuts food easily.
Depending on the condition of the blade, you may have to repeat the process several times. In extreme cases, this could be 10 times or
more. This extended process will only be necessary the first time you use the knife sharpener for this type of knife. Thereafter, you will
be able to sharpen your knife following the normal sharpening procedure.
Sometimes the sharpening wheels stall when I am drawing the knife through the blade guide slots. What causes this?
The knife sharpener is designed so that very little effort is needed to draw the knife through the slots. If too much downward pressure is
applied to the knife as it is being drawn through the slots, the sharpening wheels may stall.
Sometimes the adjustable blade guides move when I am sharpening the knife. What causes this?
If, while drawing the knife through the blade guide slots, too much pressure is applied against the face of the blade guide, the blade guide
may move. Apply less pressure while sharpening.
Product specificaties
| Merk: | Presto |
| Categorie: | Messenslijper |
| Model: | EverSharp Profesional 08810 |
Heb je hulp nodig?
Als je hulp nodig hebt met Presto EverSharp Profesional 08810 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Messenslijper Presto
15 Januari 2023
19 December 2022
Handleiding Messenslijper
- Messenslijper IKEA
- Messenslijper Krups
- Messenslijper Adler
- Messenslijper Ambiano
- Messenslijper Bartscher
- Messenslijper Beper
- Messenslijper Berkel
- Messenslijper Bifinett
- Messenslijper Blokker
- Messenslijper Bomann
- Messenslijper Domo
- Messenslijper EdgeCraft
- Messenslijper Fagor
- Messenslijper Gardenline
- Messenslijper Gastroback
- Messenslijper Gourmetmaxx
- Messenslijper Graef
- Messenslijper Gude
- Messenslijper Melissa
- Messenslijper Powerplus
- Messenslijper Princess
- Messenslijper Roadstar
- Messenslijper Salter
- Messenslijper Silvercrest
- Messenslijper Sogo
- Messenslijper Steba
- Messenslijper Studio
- Messenslijper Tower
- Messenslijper Trebs
- Messenslijper Ozito
- Messenslijper Clatronic
- Messenslijper Guzzanti
- Messenslijper OBH Nordica
- Messenslijper Orbegozo
- Messenslijper Tacklife
- Messenslijper Eldom
- Messenslijper Waring Commercial
- Messenslijper Brentwood
- Messenslijper Herkules
- Messenslijper Genie
- Messenslijper C3
- Messenslijper Orava
- Messenslijper Alpha Tools
- Messenslijper For_Q
- Messenslijper WĂĽsthof
- Messenslijper Work Sharp
- Messenslijper Petra Electric
- Messenslijper GARDE
- Messenslijper Chef's Choice
- Messenslijper IdeenWelt
- Messenslijper Donau Elektronik
- Messenslijper Sharpal
Nieuwste handleidingen voor Messenslijper
17 November 2024
17 November 2024
16 November 2024
5 September 2024
15 Augustus 2024
15 Augustus 2024
15 Augustus 2024
8 Augustus 2024
9 Juli 2024
18 Mei 2024