Premier Mounts ECM-3000 Handleiding

Premier Mounts Flat panel steun ECM-3000

Lees hieronder de 📖 handleiding in het Nederlandse voor Premier Mounts ECM-3000 (8 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Elliptical Ceiling Mount for 37˝ to 63˝ Flat Panels

Model: ECM-3000

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

1321 S. State College Blvd., Fullerton, CA 92831 USA

Warranty, Garantie, Garantía, Garanzia, Garantie, Waarborg: http://www.mounts.com/warranty 9531- 000-001- 0X Rev.0

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

ECM-3000

Mounting

Bracket Arms

Decorative

Covers

Elliptical

Tilt Mount

Triple Mount

Structure Side Skirt Thread Depth

Indicator

M6 x 25mm

32˝ Allen Wrench

M4 x 16mmM4 x 25mm M5 x 16mm M5 x 25mm

M6 x 30mm M8 x 25mm M8 x 30mm M8 x 70mm Griplate™

Washers

AST-2446/2

x18

M8 x 16mm

Minimum four (4)

complete turns

Pan Philips

Threaded

Coupler

Mount

Lower Half

Upper Half

The ceiling should be capable of supporting a weight of at least ve times

the product weight. If not, the ceiling surface must be reinforced. Proper

installation procedure by qualied personnel as outlined in the installation

instructions must be adhered to.

Mounting hardware is not included with this product. Commercially

available hardware must be used for this installation. The hardware used

will depend on your installation environment (i.e. wood stud, concrete

surface, metal I-beam etc).

Separate the upper and lower halves of the AST-2446/2 by removing both

M8 screws and wave washers. Unpack the trio mount and place it on the

ground.

The set screw on the threaded coupler must be backed out in order for the

AST-2446/2 to be threaded into place.

Thread the lower half of the AST-2446/2 into the threaded coupler on the

trio mount. The lower half of the AST-2446/2 must be threaded fully until

the piece is safely secured to the threads, then tighten the screw back into

place. Use the screwdriver to tighten the set screw once the AST-2446/2

has been attached.

The following steps must be performed by a minimum of three people:

Two people lift the trio mount into place. Align the upper and lower halves

of the AST-2446/2. Slide the lower half/trio mount into the upper half of the

AST-2446/2.

It is recommended that the height, and location, of the ECM-3000 be

determined prior to performing the following steps.

Determine the mounting height. Align the M8 mounting holes on the upper

and lower halves of the AST-2446/2 and insert the M8 screws and wave

washers. Use the 516˝ wrench to tighten the M8 screws.

Verify that all hardware is secure and tight before proceeding to the next

section.

M4 x 30mm M5 x 30mm M6 x 16mm

M6 x 45mm M8 x 45mm

Universal Spacers

AST-2446/2

Lower Half

Upper Half

M8 Pan

Philips

Screw

Allen Wrench

x1 x3 x3 x6 x6

x18

x3 x1

x18x18 x18 x18

x18 x18 x18 x12 x24

x18 x18 x18

x72

x18 x18

Required for installation

Included components

Max Flat-Panel Capacity: 80 lb. each

Inverted

Projector

Figure 1

Figure 2 Figure 3

Thread Depth

Indicator

Thread Depth

Indicator

Depth MarkDepth Mark

Thread Depth

Indicator

Threaded

Insert

Marking the

Depth

ScrewScrew

Warranty: http://www.mounts.com/warranty

Garantie, Garantía, Garanzia, Garantie, Waarborg

Updates: The most up-to-date installation

guides can be found at mounts.com

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100 | Europe +44 (0) 24 7664 4105

9531-0 0 0 -001-0X Rev. 0

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

ECM-3000

Premier Mounts’ Griplate™ Washers are designed to accom-

modate the various M4, M5, M6 and M8 hole sizes required

by flat panels.

Do not place excessive pressure on the back of the flat

panel, as this may damage your flat panel.

The Griplate™ Washer must be installed between the head

of the mounting screw and the mounting bracket as shown.

Does your flat panel have:

Recessed mount points?

Uneven mount points?

A curved back?

Any obstruction near the mount point?

If Yes, you must install nylon spacers. Remove the mount-

ing brackets, Griplate™ washers, and mounting screws from

the back of the flat panel.

Insert the Thread Depth Indicator into the thread inserts

found on the bottom or top of the projector. Use a pencil to

mark the depth of the thread insert on the Thread Depth In-

dicator, as shown. Inser t the Thread Depth Indicator into the

remaining thread inserts to compare and verify their depth.

Locate the correct diameter screw for the thread insert.

If the screw you selected is longer than the mark on the

Thread Depth Indicator, as shown in Figure 2 and Figure 3,

do not use this screw. The screw length must not bypass

the mark.

Select another screw length until you find a screw that

comes closest to the mark without going past the mark.

Test each size of the screws provided.

The correct screws should thread easily into the mount point

and not pull out when tension is applied.

The optional M3 flat washers may be used to decrease the

screw depth of either the M2.5 x 12mm screws or the M3 x

16mm screws. Decrease the screw depth by placing an M3

flat washer inside the leveling barrel and then inserting the

mounting screw.

Product specificaties

Merk:	Premier Mounts
Categorie:	Flat panel steun
Model:	ECM-3000
Kleur van het product:	Zwart
Gewicht:	63300 g
In hoogte verstelbaar:	Ja
Montagewijze:	Plafond
Maximale gewichtscapaciteit:	108.8 kg
Aantal displays ondersteund:	3
Maximale schermgrootte:	63 "
Minimale schermgrootte:	37 "