Pioneer CP-7EX Handleiding

Pioneer luidsprekersteun CP-7EX

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer CP-7EX (40 pagina's) in de categorie luidsprekersteun. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/40

CP-7EX

Speaker Stand / Socle d’enceinte / Lautsprecherständer /

Base per diffusori / Luidsprekerstandaard / Soportes de altavoz /

Suporte para colunas / Högtalarstativ / Højttalerstativ /

Høyttalerstativ / Kaiutinjalusta / Стойка под динамик

Thank you for buying this Pioneer product. This speaker

stand should only be used with the S-7EX Pioneer speaker

system. Please read through these operating instructions for

proper assembly and use. After you have finished reading the

instructions, put them away in a safe place for future

reference.

Before you start

Before setting up your speaker system, we recommend

reading the operating instructions for your system thor-

oughly.

• Only use the screws supplied when fixing the speaker to

the speaker stand.

• Do not place the stand on an unstable and/or sloping

surface. The stand and speaker may fall and cause

injury.

• Do not use with any speaker system other than the one

for which the unit was designed. The stand may collapse

and be damaged and/or the speaker may fall and cause

injury.

• When moving the speaker and stand, first remove the

speaker from the stand, and then move the stand,

holding it by the two stems.

Installing the speaker stands

Place the stand on a stable, level surface; placing the stand

on an unstable surface can be dangerous.

Adjust the position as necessary to obtain optimal sound

from your system.

• Pioneer assumes no liability whatsoever for damages

resulting from assembly, improper mounting, insuffi-

cient reinforcement, misuse of the product, acts of

nature, etc.

Assembling the speaker stands

Assemble the speaker stands as illustrated below. Please

note that a flathead screwdriver will be necessary for

assembly. The following illustration shows the fully assem-

bled speaker stand:

Speaker support

Stand base

Stand stems

Screw slots

for securing

speaker

• Align the screw slots on the stand base and screw

holes on the speaker support with the screw holes in

the two stems, then insert the screws and tighten.

The screw slots allow you to fine-tune the positioning of the

speaker.

55 mm

Black

(SBA6054)

40 mm

Black

Please note that sunken

screw holes are provided

in the speaker support.

(SBA6051)

Screws (Bind head, M6xL40)

Nut

Spike

(SBA6053)

Spike base

(SLA1057)

Screws (Bind head, M6xL55)

Speaker

support

Stand

base

Stand

stems

•Make sure you assemble the stand on a flat surface that

is relatively soft (such as a carpet).

•Make sure the screws are inserted in the screw holes as

shown above (with the screw head hidden) when

securing the speaker. Improper setup could result in

damage or injury if the speaker falls from the stand.

English

Using the spikes

The speaker stand includes spikes that you can use to isolate

the speaker from the floor. Spikes are recommended when

placing the stand on a thick carpet (for added stability), or for

better sound when placing the stand on a hard reverberant

surface (such as a concrete or wood floor). Use the supplied

spike bases to avoid scratching the floor or other surface

where the stand is placed.

Spike

Stand base plate

Nut

1 Attach the spikes to the nuts provided.

2 Attach all four spikes to the threaded metal inserts

at the base of the speaker stand.

3 Choose the location for speaker placement then put

the spike bases on the floor.

4 Place the stand so that the spikes are resting on the

spike bases on the floor.

Before placing the speaker on the speaker stand, make sure

the stand is stable and resting squarely on all four spikes.

•Note that these spikes are sharp metal and can cause

damage to flooring. Make sure to lay down a cloth or

suitable base before setting up.

•The spike bases should be placed as shown below (with

the depression on the top side).

•Make sure to use the spike bases provided to avoid

damaging the surface where you place the stand.

Attaching a speaker to the stand

To avoid accident or injury, please use screws to secure the

speaker to the speaker stand. Note that there are fastening

nuts provided on the speaker base (see below). Secure the

speaker to the speaker support using the washer, spring

washer and the 60 mm screws as shown below.

(SBA6058)

Speaker

base

Speaker

support

Washers (SBE6008)

Fastening nuts

Screws

(Bind head, M6xL60)

60 mm

Black

Spring washer

(SBE6007)

Screw slots

for securing

speaker

Cabinet and stand maintenance

•Use a polishing cloth or dry cloth to wipe off dust and

dirt.

•If the cabinet or stand is very dirty, use a soft cloth

dipped in some neutral cleanser diluted 5 or 6 times

with water. Finally, wipe again using a dry cloth. Do not

use furniture wax or cleaners.

•Never use thinners, benzine, insecticide sprays and

other chemicals on or near the cabinet or stand, since

these will corrode the surfaces.

Product specificaties

Merk:	Pioneer
Categorie:	luidsprekersteun
Model:	CP-7EX
Kleur van het product:	Zwart
Gewicht:	13000 g
Breedte:	498 mm
Diepte:	412 mm
Hoogte:	226 mm
Materiaal:	Hout
Compatibiliteit:	S-7EX