Pioneer CP-4EX Handleiding

Pioneer luidsprekersteun CP-4EX

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer CP-4EX (32 pagina's) in de categorie luidsprekersteun. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/32

http://www.pioneer.co.uk

(or http://www.pioneer.eu)

Thank you for buying this Pioneer product. This speaker stand

should only be used with the S-4EX Pioneer speaker system.

Please read through these operating instructions for proper

assembly and use. After you have finished reading the

instructions, put them away in a safe place for future reference.

Before you start

Before setting up your speaker system, we recommend reading

the operating instructions for your system thoroughly.

• Do not use this speaker stand with speakers other than the

Pioneer S-4EX, since the product balance may be impaired,

resulting in tipping or dangerous falls.

• Only use the screws supplied when fixing the speaker to the

speaker stand.

• Do not place the stand on an unstable and/or sloping surface.

The stand and speaker may fall and cause injury.

• Do not use with any speaker system other than the one for

which the unit was designed. The stand may collapse and be

damaged and/or the speaker may fall and cause injury.

• When moving the speaker and stand, first remove the speaker

from the stand, and then move the stand, holding it by the

stems.

• Place the stand on a stable, level surface; placing the stand on

an unstable surface can be dangerous.

• Pioneer assumes no liability whatsoever for damages

resulting from assembly, improper mounting, insufficient

reinforcement, misuse of the product, acts of nature, etc.

Names of Parts

Attaching speakers to the

stands

A medium Phillips screwdriver is required for attaching the

speakers.

Assembly with the S-4EX speaker

system

If you are using the S-4EX speaker system, note that there is a

fastening nut provided on the speaker base (see below).

When installing spikes on speaker

Use only spikes supplied with S-4EX.

1 Set spikes into three locations on bottom of speaker.

Consult the S-4EX operating instructions for additional

instructions.

2 Apply the furnished cork plates on the three locations on

the speaker support.

3 Rest the speaker gently on the speaker support while

aligning the spikes with the cork plates on the top of the

speaker support, then fix in placing using the washers,

spring washers, and screws (bind head M5 x L55).

S eake su o tp r pp r

Stand stems

Stand base

Screw holes

fo secu eaker ring sp r

Non-skid

co adsrk p

S eakep r

su o tpp r

Co latesrk p

[SEC2255]

55 mm

Black

S eake basep r

S eakep r

su o tpp r

Sc ew holesr

fo secu ingr r

s eakep r

Fastening nut

Washer

[SBE6006]

S ing washepr r

[SBE6005]

Screws

(Bind head, M5 x L55)

[SBA1307]

Co latesrk p

English

When mounting spikes on speaker stand

Use only spikes, spike bases, and auxiliary feet provided with

the S-4EX.

1 Install spikes in three locations on the bottom of the

stand base plate, then install the two auxiliary feet to

prevent rocking.

2 Place spike bases on the floor in the position where the

spikes will rest.

3 Rotate the spikes to adjust the height, then rotate the

spike nuts counterclockwise to lock the height of the spike.

4 Rest the speaker stand on the spike bases and check to

confirm the stand is stable without any rocking.

5 Rotate the auxiliary feet to adjust height.

Adjust the height so that about 1 mm to 2 mm of space

remains open between the feet and the installation surface.

6 Rotate the nuts counterclockwise to lock the height.

7 Rest the speaker on the top of the stand and use washers,

spring washers and screws (bind head M5 x L55) to fasten

the speaker securely to the stand.

• When installing spikes, lay the speaker stands on their sides

on a soft blanket or surface to prevent scaring.

• Set the spike bases with the concave side upward to receive

the spike as shown below.

• When the spikes are used alone without spike bases,

scratches may be cuased to the floor or other installation

surface. Always use the spike bases when using spikes.

Other Information

Stand maintenance

• Use a polishing cloth or dry cloth to wipe off dust and dirt.

• If the stand is very dirty, use a soft cloth dipped in some neutral

cleanser diluted five or six times with water. Finally, wipe again

using a dry cloth. Do not use furniture wax or cleaners.

• Never use thinners, benzine, insecticide sprays and other

chemicals on or near the stand, since these will corrode the

surfaces.

Specifications

External dimensions. . . . . . . 360 (W) mm x 570 (H) mm x 485 (D) mm

14 3/16 (W) in. x 22 1/2 (H) in. x 19 1/8 (D) in.

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9 kg (30 lb 11 oz.)

Supplied accessories

Screws (Bind head, M5 x L55) [SBA1307] . . . . . . . . . . . . . . . . . . . . . . 2

Spring washers [SBE6005] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Washers [SBE6006] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cork plates [SEC2255] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

These operating instructions [SRD6100]

• Specifications and design subject to possible modification

without notice, due to improvements.

• The product number are listed above in square brackets.

S ikep

S ike nutp

Stand base plate

Auxilia y feetr

55 mm

Black

S eake basep r

S eakep r

su o tpp r

Sc ew holesr

fo secu ing s eaker r p r

Fastening nut

Washer

[SBE6006]

S ing washepr r

[SBE6005]

Sc ewsr

(Bind head, M5xL55)

[SBA1307]

Replacement part numbers

Part name

• Protector (Bottom)

• Protector (Top)

• Packing case

• Protection sheet

Part no.

SHA2632

SHA2631

SHH1324

SHC1879

Published by Pioneer Corporation.

Product specificaties

Merk:	Pioneer
Categorie:	luidsprekersteun
Model:	CP-4EX
Kleur van het product:	Zwart
Gewicht:	13900 g
Breedte:	360 mm
Diepte:	485 mm
Hoogte:	570 mm
Compatibiliteit:	S-4EX
Minimale afstand tot vloer:	576 mm
Maximale afstand tot vloer:	576 mm