Pioneer CP-2EX Handleiding

Pioneer luidsprekersteun CP-2EX

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer CP-2EX (40 pagina's) in de categorie luidsprekersteun. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/40

CP-2EX

Speaker Stand / Socle d’enceinte / Lautsprecherständer /

Base per diffusori / Luidsprekerstandaard / Soportes de altavoz /

Suporte para colunas / Högtalarstativ / Højttalerstativ /

Høyttalerstativ / Kaiutinjalusta / Стойка под динамик

Thank you for buying this Pioneer product. Please read

through these operating instructions for proper assembly

and use. After you have finished reading the instructions, put

them away in a safe place for future reference.

Before you start

Before setting up your speaker system, we recommend

reading the operating instructions for your system thor-

oughly.

• Only use the screws supplied when fixing the speaker to

the speaker stand.

• Do not place the stand on an unstable and/or sloping

surface. The stand and speaker may fall and cause

injury.

• Do not use with any speaker system other than the one

for which the unit was designed. The stand may collapse

and be damaged and/or the speaker may fall and cause

injury.

• When moving the speaker and stand, first remove the

speaker from the stand, and then move the stand,

holding it by the two stems.

Installing the speaker stands

Place the stand on a stable, level surface; placing the stand

on an unstable surface can be dangerous.

When placing the speaker, keep in mind that the tone is

affected by the position of the speaker.

If the bass is insufficient, move the speaker closer to the wall.

The richest bass sound is obtained when the speaker is right

against the wall. If the bass is too powerful, producing a

muffled tone, move the speaker away from the wall. Placing

the speaker against a thick curtain may also be effective.

50 cm 20 cm

Adjust the position as necessary to obtain optimal sound

from your system.

•Pioneer assumes no liability whatsoever for damages

resulting from assembly, improper mounting, insuffi-

cient reinforcement, misuse of the product, acts of

nature, etc.

Assembling the speaker stands

Assemble the speaker stands as illustrated below. Please

note that a flathead screwdriver will be necessary for

assembly. The following illustration shows the fully assem-

bled speaker stand:

Screw holes

for securing

speaker

Speaker support

Stand base

Stand stems

• Align the screw holes on the stand base and speaker

support with the screw holes in the two stems, then

insert the screws and tighten.

Screws (Bind head, M6xL40)

40 mm

Black

Screws (Bind head, M6xL40)

Nut

Spike (SBA6053)

Spike base

(SLA1057)

40 mm

Black

Speaker

support

Stand

base

Stand

stems

Please note that sunken

screw holes are provided

in the speaker support.

(SBA6054)

•Make sure you assemble the stand on a flat surface that

is relatively soft (such as a carpet).

•Make sure the screws are inserted in the screw holes as

shown above (with the screw head hidden) when

securing the speaker. Improper setup could result in

damage or injury if the speaker falls from the stand.

English

Using the spikes

The speaker stands include spikes that you can use to isolate

the speaker from the floor. Spikes are recommended when

placing the stand on a thick carpet (for added stability), or for

better sound when placing the stand on a hard reverberant

surface (such as a concrete or wood floor). Use the supplied

spike bases to avoid scratching the floor or other surface

where the stand is placed.

Spike

Nut

Stand base plate

1 Attach the spikes to the nuts provided.

2 Attach all four spikes to the threaded metal inserts

at the base of the speaker stand.

3 Choose the location for speaker placement then put

the spike bases on the floor.

4 Place the stand so that the spikes are resting on the

spike bases on the floor.

Before placing the speaker on the speaker stand, make sure

the stand is stable and resting squarely on all four spikes.

•Note that these spikes are sharp metal and can cause

damage to flooring. Make sure to lay down a cloth or

suitable base before setting up.

•The spike bases should be placed as shown below (with

the depression on the top side).

•Make sure to use the spike bases provided to avoid

damaging the surface where you place the stand.

Attaching speakers to the stands

To avoid accident or injury, please use screws to secure the

speakers to the speaker stands.

Assembly with the S-2EX speaker system

If you are using the S-2EX speaker system, note that there is

a fastening nut provided on the speaker base (see below).

When using speaker spikes:

Place the speaker spike bases in the four holes provided on

the speaker support, then secure the speaker to the speaker

support using the washer, spring washer and the 62 mm

screws as shown below.

(SBA6050)

Speaker

base

Speaker

support

Washer (SBE6006)

Speaker

spike base

Fastening nut

Spring washer

(SBE6005)

Screws

(Bind head, M5xL62)

62 mm

Black

Screw holes

for securing

speaker

When not using speaker spikes:

Secure the speaker to the speaker support using the washer,

spring washer and the 36 mm screws as shown below.

(SBA6048)

Speaker

base

Speaker

support

Washer (SBE6006)

Fastening nut

Screws

(Bind head, M5xL36)

36 mm

Black

Screw holes

for securing

speaker

Spring washer

(SBE6005)

Product specificaties

Merk:	Pioneer
Categorie:	luidsprekersteun
Model:	CP-2EX
Kleur van het product:	Zwart
Gewicht:	19000 g
Breedte:	400 mm
Diepte:	513 mm
Hoogte:	604 mm
Compatibiliteit:	S-2EX
Minimale afstand tot vloer:	604 mm
Maximale afstand tot vloer:	604 mm