PAC OnStar OS-4 Handleiding

PAC Niet gecategoriseerd OnStar OS-4

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC OnStar OS-4 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 223 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com Page 1

10-29-10

The OS-4 is a plug and play interface that allows the replacement of a General Motors GMLAN factory radio. The OS-4 will

maintain operation of the OnStar® system in vehicles with Bose® audio systems, amplied audio systems and also audio

systems without external ampliers . The OS-4 has on board switching that allow audio from the OnStar® system to play

through the two front factory speakers. This interface retains all warning chimes, audible turn signal indicators, Bluetooth

and the Vehicle Rear Parking Assist System (if equipped). The factory XM radio tuner can be controlled from the Steering

Wheel Controls (SWC) or Rear Seat Entertainment (RSE) Controls. RSE headphone jacks will also remain active and are

designed for use with dual zone radios and the factory installed XM tuner. If the overhead LCD is present the IR headphone

system will also be active.

General Motors OnStar®

Interface for GMLAN Vehicles With or

Without Factory Amplied Audio Systems

*These instructions only support revision 1.2.3.8 or higher of the OS-4

1. The OS-4 will retain the use of the factory installed XM receiver. Factory SWC or RSE Controls must be present for use of this feature.

2. You may use this interface if the vehicle does not have OnStar® but you need to interface with the Bose® amplier

3. This interface will work in amplied or non-amplied audio systems.

4. This interface retains the 5.1 audio system in equipped Cadillac vehicles.

5. Built in Smart Mute Circuitry will play OnStar® through the front speakers and allow the RSE audio jacks to continue playing the audio

source selected by the RSE Controls.

• OnStar® active LED and Ignition on LED.

• New radio will operate with the vehicle RAP (Retained Accessory Power) system.

• Provides +12v RAP circuit, Illumination, Vehicle Speed Sensor (VSS) Output, Parking brake, and Reverse trigger outputs.

• OnStar® Volume control via factory steering wheel audio controls or a push-button switch.

• Safety chime audio level is controlled through the Driver Information Center (DIC).

• RSE Controls will play the aftermarket radios dual zone source or the factory XM tuner if serviced.

• Overhead RSE LCD is usable as well as factory IR headphone system and Rear Auxiliary Input Jacks (use PAC Part # GMRVD).

• Steering wheel radio controls can be retained to control new radio by using the SWI-X, ECL2, JACK or PS.

J1850

Class 2

VPW

Class 2

J1850

1 0 0 0 1 0 1 0 0 1 0 0 1 0 1 01 1 1 1 1 1 1 0

1 1 1 11 0 1 0 0 0 0 1 0 1 01 1 1 0 0 1 01 0

Arbitration

EOD

CRC

1 0 0 0 1 0 1 0 0 1 0 0 1 0 1 01 1 1 1 1 1 1 0

1 1 1 11 0 1 0 0 0 0 1 0 1 01 1 1 0 0 1 01 0

Class 2

J1850

Notes

Installation

OS-4

OS-GMLAN29

OS-NAV

XM R

XM L

Connect to SWC

Interface. Program

for Version 2.

OS-RADPWRAUDIO

• Aftermarket radio connections are made at the 20-pin OS-RADPWRAUDIO connector. A

detailed description of these wires is on the next page. PLEASE NOTE: The audio inputs

of the OS-4 are designed to be used with the aftermarket head unit’s speaker output

ONLY (60W X 4 MAX). If you are using an additional aftermarket amplier, you must

make your speaker connections AFTER the OS-4 at the Vehicle Connections plug.

If you want to retain OnStar while using an aftermarket amp, a seperate speaker

must be hooked up to the front left output of the OS-4.

• If the vehicle has Rear Seat Audio Controls and the XM tuner is serviced plug the 8 pin

XM Audio output cable into the OS-4. The RCA cables will feed the XM audio into the

aftermarket radios AUX input (if available). The XM RCA cables are not necessary for

Rear Seat Audio but will allow the headunit to play the XM audio through the cabin.

• Factory installed audio options such as Bose, Harman Kardon or Pioneer ampliers

will determine the 16-pin OS-GMLAN29 connection. If the vehicle has a factory installed

amplier use the Factory Amplier Audio location. If a factory installed amplier is not

present use the Non-Amplied Factory Audio location.

• The OS-NAV connector has VSS, Reverse and Parking Brake outputs as well as the

OnStar push button volume adjustment input.

• If SWC buttons are present and retained using a radio specic SWC interface use the

provided plug. No other connections or splices are necessary.

• The CMX retains all factory warning and safety chimes. If the vehicle chimes when the

radio is removed the CMX is not needed.

• The Mute loop (if not cut) will turn the ACC. output off when an OnStar or Bluetooth call

is made or received. If the aftermarket radio has a mute input cut this loop and connect

the outer brown wire to the mute input.

Vehicle Connections

Navigation Connections

SWC Interface

Connections

Upgraded Radio Connections

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com Page 2

10-29-10

Connecting to and Using OnStar

Connecting the OS-4 to an aftermarket radio

SWC Output Connector

Press and

Hold for

1.5 seconds

to Activate

Onstar Voice

Recognizition or

Bluetooth Phone

Services

Raises and

Lowers Onstar

the Audio

Level While

Onstar is

Active

(7 positions)

Activate

Onstar Voice

Recognizition

Services

Connect to

Onstar

Personal

Calling

Setvices

Onstar

Emergency

Services

Ends Current

Onstar Call

or Rejects

Incoming

Bluetooth or

OnStar Call

SRCE

• To activate Bluetooth Services (if present) and OnStar Services if Bluetooth is not present press and

hold the Speak SWC button for 1.5 seconds. Pressing the circled phone button on the OnStar touch

pad will only activate OnStar Services.

• Pressing the SWC Vol+ or Vol- during an OnStar/Bluetooth connection will raise and lower the

OnStar or Bluetooth audio level.

• Pressing the down arrow SWC button or circled phone button on the OnStar touch pad during an

OnStar or Bluetooth call will end the current OnStar connection. The down arrow will also reject

incoming OnStar or Bluetooth calls.

• OnStar Personal calling and Emergency services can be activated by the buttons on the mirror.

OnStar Level Control for Vehicles without SWC Buttons

• If SWC buttons are not present a SPST switch can be used to control the

OnStar audio level during an OnStar connection.

• Using the provided Green/White wire, connect the non-terminated end to one

side of a SPST normally open momentary switch (not included).

• The terminated end will go into the OS-NAV connector position X (see picture

above).

• The other side of the SPST switch will be connected ground.

• When OnStar is active pressing the switch will raise the audio level 7 times

before returning to the original level.

1324

Green/White wire

SPST N.O. switch (not included)

Wire insertion side view

(OS-NAV 24-pin connector) VSS

(purpl e/white)

Parking

Brake

(red/white)

Reverse

(green)

O.S.

Level Switch

(green/white)

1 Green/White OnStar Level Control

2 N.C.

3 N.C.

4 N.C.

5 N.C.

6 N.C.

7 N.C.

8 Purple/White Vehicle Speed Sensor Output

9 N.C.

10 N.C.

11 N.C.

12 N.C.

13 N.C.

14 N.C.

15 N.C.

16 N.C.

17 Green Reverse Light Output

18 Red/White Parking Brake Output

19 N.C.

20-24 N.C.

1 White FL+ Speaker Input

2 Grey FR+ Speaker Input

3 N.C.

4 N.C.

5 Black Ground

6 Yellow Battery

7 Brown Mute Sense Input

8 Purple RR+ Speaker Input

9 Green RL+ Speaker Input

10 Brown Mute Output (-)

11 White/Black FL- Speaker Input

12 Grey/Black FR- Speaker Input

13 Red RAP Output

14 Burgundy Chime+

15 Orange Illumination Output (+)

16 Blue/White Amp On Input

17 White/Green SWC Output

18 Purple/Black RR- Speaker Input

19 Green/Black RL- Speaker Input

20 Black Chime -

OS-NAV

(Wire side view)

OS-RADPWRAUDIO

(Wire side view)

• The OS-4 provides a SWC output connector attached to the

OS-RADPWRAUDIO harness. For ease of installation, all necessary

connections for a SWI-X, ECL2, JACK, or PS have made for you.

• When using this SWC output connector the radio specic SWC interface

must be programmed for version 2 (refer to SWC interface programming

instructions for exact programming sequence).

• Both loops should also remain in tact.

• During steering wheel button assignment programming each button

should be pressed and held for 1 second after the SWC interface LED

goes out with the exception of the Speak button.

• The speak button should be pressed for less than 1 second and

released.

• Pressing the Speak button for longer than 1.5 SEC will activate OnStar.

From SWC

Buttons

From OnStar Touch Pad

Connect to SWC

Interface. Program

for Version 2.

Connect to Radio

Specific SWC

Interface

Using the CMX

• The provided CMX will play all safety/warning

chimes and turn signal/hazard light tones in

vehicles that do not play these chimes/tones when

the factory installed radio is removed.

• When the radio is removed - if factory chimes still

play the CMX is not needed. The CMX cable (2-pin

connector attached to the OS-RADPWRAUDIO

interface harness) should be tied up as it is not

used for any other connections.

• To adjust the level of the warning and safety

chimes refer to the vehicles owner manual for

Driver Information Center (DIC) settings. Not all

vehicles have a DIC. If the DIC is not available the

chime level is not adjustable.

Center and Sub Connections

Center

SUB

• Some Cadillac vehicles are

equipped with a Dolby Surround

Sound Amplied Audio System. The

ampliers 5.1 mode is enabled when

the RSE system is off and OnStar is

not active. If the aftermarket radio

has a dedicated center channel

and or sub output connect it to the

provided cable as labeled. Refer to

the aftermarket radios owner manual

for surround sound settings and

adjustments.

• If the aftermarket radio to be

installed does not have a dedicated

center channel or sub output do not

use this cable. To ensure best sound

performance channel summing is

not recommended. Use this cable

according to the outputs that are

available.

• This cable can also be used for

factory reverse camera retention if

available and if center channel and

or sub connections are not needed

(see Notes section of this manual).

Pacic Accessory Corporation - Santa Ana, CA 92705

techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com Page 3

10-29-10

• To activate the XM controls press and hold the “Source” button until a chime is heard. The Driver Information

Center (DIC) in the instrument cluster will display “XM Control On”.

• Arrow up moves forward through the channels. The channel name will be displayed on the DIC.

• Arrow down moves backwards through the channels. The channel name will be displayed on the DIC.

• To store a preset, rst choose the preset location by pressing the “Play” button repeatedly. The DIC will display

the XM preset locations. When the desired preset location is displayed, tune to the desired station, then press and

hold the “Play” button to store

• To recall a preset simply press the “Play” button repeatedly until the desired preset is displayed.

• To de-activate the XM controls press and release the “Source” button

PLEASE NOTE: You MUST be installing an aftermarket radio that is equipped with an auxiliary input

to be able to retain the factory XM audio. If the vehicle is equipped with steering wheel controls other

than the ones pictured to the right the OS-4 will not be able to control the factory XM tuner as the

required buttons are not present.

Using the Rear Seat Audio Controls

Turns the

Rear Seat

Controls On

or Off

Change between

Factory XM tuner

and Dual Zone

Radio Source

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

and Bar Button)

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

Down Button)

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

Up Button)

XM 16

Turns the

Rear Seat

Controls On

or Off

Change between

Factory XM tuner

and Dual Zone

Radio Source

Scrolls through

Presets 1-6

Seek to the

Factory XM

Tuner Station

Seek to the

Factory XM

Tuner Station

Using the Radios Dual Zone Source Using the Factory XM Radio Tuner

• Press the power button to turn the RSE Controls on. When Radio is displayed on the RSE

Controls, the aftermarket radios rear speaker output will be heard through the headphone

jacks. Putting the aftermarket radio into dual zone mode should change the output level

of the rear speakers to a xed level. This allows precise user adjustment from the level

knobs on the RSE Controls (refer to aftermarket radio owners manual for model specic

dual zone operation).

• The seek arrows and PROG button will control the radio as programmed by the SWC

interface. These buttons are mapped to the SWC buttons as stated above.

• Pressing the SRCE button will toggle between the Factory XM tuner and the Radio as the

RSE source. Pressing the power button will turn the RSE Controls off as well as turning

the key off. The seek arrows and PROG button will continue to operate as stated (with the

exception of SRCE which has no function) when the Rear Seat Controls are turned off.

• Press the power button to turn the RSE Controls on. If Radio is displayed press the

SRCE button to select factory XM tuner mode. When XM followed by the channel number

is displayed factory XM tuner audio will be heard through the headphone jacks.

• The Seek arrows will control the factory XM radio tuner and select the desired station.

• The PROG button will scroll through Presets 1-6

• Pressing the SRCE button will toggle between the Factory XM tuner and Radio as

the RSE source. Pressing the power button or turning the key off will turn off the RSE

Controls.

• The factory XM tuner must remain serviced to take advantage of this feature. Visit www.

xmradio.com for a complete up-to-date channel listing and service options.

• In order for the RSE controls to properly work the XM tuner, the front XM controls must

be set to off.

Using the Factory XM Radio Tuner With the Steering Wheel Controls

SRCE

Press & release to

recall a preset.

Press & hold to store

a preset.

Moves back

through the XM

channels

Moves forward

through the XM

channels

Press & hold to

enable XM controls.

Press & release to

disable XM controls

Factory XM Controls

Volume Up

Volume Down

Installation Notes

1. Before the interface is connected to the vehicle ensure the key is off and the driver’s door is open. After the OS -4 is connected the rst time, start

the vehicle and run for at least 15 seconds. Turn the ignition key off and open the driver’s door. The ignition key can now be turned back on and the

interface and radio tested.

2. The audio inputs of the OS-4 are designed to be used with the aftermarket head unit’s speaker output ONLY (60W X 4 MAX). If you are using an

additional aftermarket amplier, you must make your speaker connections AFTER the OS-4 at the Vehicle Connections plug. If you want to retain

OnStar while using an aftermarket amp, a seperate speaker must be hooked up to the front left output of the OS-4.

3. DO NOT cut the Brown loop on the SWC interface connector. Program the radio specic SWC Interface for version

#2.

4. When the Rear Seat Audio jacks are activated in any vehicle OTHER than the Cadillac Escalade or a UQA amplied

vehicle the rear speakers will mute.

5. The headphone jacks will play the rear zone source selected by the head unit (refer to the new radios instruction

manual for details on this feature if equipped). Maximize the rear zone volume level (this will reduce unwanted

noise). During an OnStar call the front speakers play OnStar, the rear speakers are muted and the headphones will

continue to play the rear zone audio source.

6. Using the Center and Sub cable for factory reverse camera retention.

• With the supplied brown connector NOT attached to the vehicles brown radio connector: lift the upper and

lower locking tabs near the wire insertion part of the supplied brown connector which houses the center and

sub RCA cables.

• Depress the silver exposed locking tabs on which ever RCA connector (center or sub) is not being used during

this installation.

• After removing both shield (black) and center conductor (red or white) pins - re-insert as follows (see image

aside).

• Pin 6 is the camera+ signal and Pin 7 is the camera- signal. After inserting the pins clasp the locking tab back

down to lock the moved pins into place.

• Fit the modied brown connector into the vehicles brown connector and plug the moved RCA cable into the

aftermarket radios camera input (mark this RCA cable for future reference).

• Use the supplied reverse output wire (green wire in OS-NAV connector) for automatic switching when the

vehicle is put into reverse.

12345678

916

Center and Sub

Brown Connector (supplied

with interface)

3: Center +

4: Sub +

6: Camera +

7: Camera -

11: Center -

12: Sub -

101112131415

Wire side view

7. DTS, Equinox, Torrent and Vue Installation Notes:

If the vehicle is equipped with a factory amplier other than a Bose amplier and OnStar audio is not heard

during operation the Black/White wire located in the OS-GMLAN29 harness needs to be cut in half and insolated

at both ends (c2 vehicle (16pin) connector pin 8) .

Radio

Product specificaties

Merk:	PAC
Categorie:	Niet gecategoriseerd
Model:	OnStar OS-4

Heb je hulp nodig?

Als je hulp nodig hebt met PAC OnStar OS-4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd PAC

PAC RP4-GM31 Handleiding

31 Augustus 2024

PAC NU-GM51 Handleiding

28 Augustus 2024

PAC NAV-1129 Handleiding

28 Augustus 2024

PAC LP7-2R Handleiding

28 Augustus 2024

PAC LP7-4 Handleiding

28 Augustus 2024

PAC GMK367B Handleiding

28 Augustus 2024

PAC CP1-FRD1 Handleiding

28 Augustus 2024

PAC C2A-CHY5 Handleiding

28 Augustus 2024

PAC NU-GM3 Handleiding

28 Augustus 2024

PAC CP1-TSL1 Handleiding

28 Augustus 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Livarno Lux IAN 071407 Handleiding

29 November 2024

Livarno Lux IAN 317128 Handleiding

29 November 2024

Livarno Lux IAN 049213 Handleiding

29 November 2024

Livarno Lux ST-1002 Handleiding

29 November 2024

Livarno Lux HG02489 Handleiding

29 November 2024

Livarno Lux HG02189 Handleiding

29 November 2024

Livarno Lux IAN 365198 Handleiding

29 November 2024

Livarno Lux IAN 367074 Handleiding

29 November 2024

Livarno Lux HG00701 Handleiding

29 November 2024

Livarno Lux IAN 337273 Handleiding

29 November 2024