Ozito TBS-2010 Handleiding

Ozito Niet gecategoriseerd TBS-2010

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito TBS-2010 (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/10
ONLINE MANUAL
Scan this QR Code with your mobile
device to take you to the online manual.
T BS- 2010
Made in China
FO R TIM BER ONLY
(Diameter) Ø254 x (Bore) Ø30 x (Kerf) 2.4mm
FOR USE WITH TABLE SAWS O NLY
TIMB ER SAW B LADE
TUNGSTEN
CARBIDE
TEET H
24
mm
(10”)
254
MAX S PEE D
7,000/MIN
WARNI N G !
• Do not us e this tungsten carbide tipped blade for mas onr y or metal cutting applications.
• Always us e s harp blades . Always ins pect blades for any da mage & cra cks .
• Refer to the power tool m anual for s afety warnings , blade m ounting & ope rating instructions .
• Always wear ey e, ear & res piratory protection. Always wear gloves .
0
I
2000W
TABLE
SAW
TABLE SAW
2000W
TABLE SAW
WITH STAND
2000W
ASSEMBLY MANUAL
0522
1. Table Saw
2. 254mm Saw Blade
3. Riving Knife
4. Sliding Mitre Gauge
5. Small Hex Nuts
6. Small Hex Bolt
7. 4 x Frame Legs
8. 4 x Cross Braces
9. 4 x Table Cross Braces
10. 20 x Nuts
11. 10 / 21mm Spanner
12. 10 / 13mm Spanner
13. 36 x Bolts
14. 4 x Foot Caps
15. 2 x Bracing Brackets
16. 2 x Short Table Struts
17. 2 x Long Table Struts
18. 2 x Table Extensions
19. Push Stick
20. Rip Fence
21. Blade Guard
STANDARD EQUIPMENT
2
9
10
11
12
3
7
8
4
5
6
1
21
20
15
13
14
19
18
17
16
1. Ensure the blade height is
wound fully down and then
turn the table saw upside
down on the floor.
2. Remove any cardboard boxes from
behind the motor; it can be easily
accessed by tilting the blade using
the bevel adjustment dial.
3. Align a table leg with the bolt
holes on the table saw and
attach it loosely with 2 of
the bolts. Repeat this for the
other 3 legs.
Note: Some of these bolts will
need to be removed later, so
only attach loosely.
4. Place the flat side of a cross
brace against the inside face
between 2 legs. Use 4 bolts
and nuts to secure the brace
in place. Repeat the same
procedure for the other 3
cross braces.
Note: Only fully tighten the bolts and nuts once the machine has
been fully assembled, flipped onto its feet and placed on a level
surface to ensure the frame is level.
5. Fit the rubber foot caps onto the
ends of the legs.
6. Use 2 bolts and nuts to
attach a bracing bracket to
one of the rear legs. Repeat
for the other bracing bracket
and rear leg.
7. To assemble the push stick
holder, screw one of the
small nuts onto the small
hex bolt.
8. Place this through one of the
holes on either of the front
legs and use the other small
nut to secure this in place.
Note: Unwind the hex bolt slightly if there is not enough space for
the push stick to hand securely.
1. ASSEMBLING THE FRAME
0
I
2000W
TABLE
SAW
200
TABLE
SAW
0
I
2000W
TABLE
SAW
0
I
2000W
TABLE
SAW
WARNING! ENSURE THE TOOL IS TURNED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING OPERATIONS.
TBS-2010
1. Use a Philips head
screwdriver (not supplied) to
loosen and remove the table
insert.
2. Remove the blade bolt. Use 21mm
and 13mm spanners to loosen it if
necessary.
3. Remove the outer flange.
4. Thread the saw
blade onto the
axle and then
replace the
outer flange and
bolt.
Note: Ensure the rotation arrows on the blade matches the
direction of the guide arrows in the blade cavity.
Note: Ensure that the inner flange is attached to the motor shaft.
5. Use the 21mm spanner to
hold the axle while using the
13mm spanner to tighten
the bolt.
6. Use the 13mm spanner to loosen the
riving knife plate.
7. Slot the riving knife behind
the plate, leaving a 3-8mm
gap between the riving knife
and blade teeth.
8. Retighten the bolt to secure
the riving knife in place.
9. Replace the table insert by
sliding the back end in first
under the lip of the blade
cavity, then redoing the
Philips head screw.
10. Slide the blade guard over
the riving knife, aligning
the bolt with the hole in the
riving knife. Turn the bolt
clockwise to lock it in place.
WARNING! THE BLADE GUARD MUST ALWAYS BE
LOWERED OVER THE WORKPIECE BEFORE BEGINNING
TO CUT.
1. With the table saw still
upside down on a flat
surface, align a table
extension with the side of the
table saw.
2. Place a cross brace on the
extension piece and align
it with the bolt holes in the
table extension.
3. Use a bolt to secure the table
extension and table cross
brace to the table saw.
4. Repeat steps 2 and 3 for the other cross brace and then attach
the other table extension in the exact same manner.
5. Use another bolt to attach a
table strut to the outside of
the table extension. Repeat
for the other 3 table struts.
Note: One pair of table struts
is longer than the other. The
longer pair of table struts
should be used on the side of
the table saw with the power cord.
6. Undo the bolt on the table leg
side and use this to secure a
table strut against the table
leg & saw. Repeat for the
other 3 table struts.
7. Flip the table saw onto its feet and tighten up all of the bolts.
3. FITTING THE BLADE ASSEMBLY2. ATTACHING THE TABLE EXTENSIONS
BLADE
BOLT
OUTER
FLANGE
BLADE
TABL E SAW
2000W
3 - 8mm
0
I
0
0
I
2000W
TABLE
SAW
FRONT SIDE
0
I
2000W
TABL E
SAW
TBS -2 0 10
Made in C h in a
FOR TIMBER ONLY
(Diameter) Ø254 x (Bore) Ø30 x (Kerf) 2.4mm
FOR USE WITH TABLE S AWS ONLY
TIMBER SAW BLADE
TUNGSTEN
CARBIDE
TEETH
24
mm
(10” )
254
MAX SPEED
7,000/MIN
WARNING!
• Do n o t u se thi s tun g sten carbi de ti p ped bl ade fo r m aso nry o r m etal cut tin g app l icatio ns.
• Always use sharp bl ades. Al ways inspect b lades fo r any d amag e & cracks.
• Refer to th e po wer to o l m anu al fo r safety warnin gs, bl ade m o un ti n g & o p erating i nstru ctio n s.
• Always wear eye, ear & respiratory p ro tectio n. A lways wear glo ves.
0
I
2000W
TABLE
SAW
TABLE SAW
2000W
TABLE SAW
WITH STAND
2000W
INSTRUCTION MANUAL
SPECIFICATIONS
Mains Voltage: 230–240V ~ 50Hz
Input Power: 1800W; 2000W (S6 40%)
No Load Speed: 5,000/min
Blade: Ø254 x Ø30mm x 2.8mm
Blade Teeth: 24TCT
Bevel Angle: 0 - 45° Left
Blade Height: 0 - 85mm
Max. Cutting Capacity: 85mm @ 90°;
65mm @45°
Table Size: 563 x 583mm
893 x 583mm (with extensions)
Dust Port: Ø35mm
Weight: 18.8kg
TBS-2010
STANDARD EQUIPMENT
3 YEAR REPLACEMENT WARRANTY*
Your product is guaranteed for a period of If 36 months from the original date of purchase.
a product is defective it will be replaced in accordance with the terms of this warranty. Warranty
excludes consumable parts, for example: valve adapters and accessories.
*This product is intended for DIY use only and replacement warranty covers domestic use.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other than that specified on the tool.
• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
Ozito Industries Pty. Ltd. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
ozito.com.au
Table Saw & 254mm Blade
Blade Guard, Riving Knife, Rip
Fence, Sliding Mitre Gauge, Push
Stick, Hex Bolt & 2 x Small Nuts
2 x Table Extensions, Base Frame
Components, Assembly Fasteners &
2 x Spanners
0622
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY
YOU MUST RETURN THE PRODUCT TO YOUR NEAREST
BUNNINGS WAREHOUSE WITH YOUR BUNNINGS
REGISTER RECEIPT. PRIOR TO RETURNING YOUR
PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
Australia: 1800 069 486
New Zealand: 0508 069 486
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE
THE MODEL NUMBER AND DATE OF PURCHASE
AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE
WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS
YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.

Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: TBS-2010

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito TBS-2010 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Ozito

Ozito

Ozito PXLEK-1840 Handleiding

2 November 2024
Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024
Ozito

Ozito PXNGS-218 Handleiding

8 April 2024
Ozito

Ozito PXHTBK-2518 Handleiding

8 April 2024
Ozito

Ozito PSR-5732U Handleiding

16 Maart 2024
Ozito

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024
Ozito

Ozito PXWBS-200U Handleiding

16 Maart 2024
Ozito

Ozito PXDDK-301U Handleiding

16 Maart 2024
Ozito

Ozito PXCPPS-018U Handleiding

16 Maart 2024
Ozito

Ozito WPHGK-2000U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024