Ozito PXLEK-1840 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXLEK-1840 (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
CORDLESS
LAWN EDGER
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V
No Load Speed: 4,000/min
Cutting Depths: 36.5, 40, 45mm
Blade: 190mm x 18mmØ
Weight: 3.0kg
PXCLES-018
STANDARD EQUIPMENT
Cordless Lawn Edger
WARRANTY
ozito.com.au
0822
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty. Warranty excludes consumable parts, for example: bearings, blade,
blade nut, and included accessories.
Blade Spanner & Pin
OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
WARNING
The following actions will result in the warranty being
void.
If the tool has been operated on a supply voltage other than that specied
on the tool.
If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
Failure to perform maintenance as set out within the instruction manual.
If the tool is disassembled or tampered with in any way.
Professional, industrial or high frequency use.
ONLINE MANUAL
Scan this QR Code with your mobile device
to take you to the online manual.
BATTERY & CHARGER
This tool is compatible with all battery and chargers from
the Ozito PXC Range.
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
1. Align both halves of the shaft together, pushing the
upper shaft into the lower. Push until the collar is
up against the lower shaft.
Shaft Assembly
WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
BATTERY IS DISCONNECTED BEFORE PERFORMING ANY
OF THE FOLLOWING TASKS.
CORDLESS LAWN EDGER
1 2 3 4
1. Rear Handle
2. Lock-Off Switch
3. On/Off Trigger
4. Adjustable Handle
5. Shaft Lock
6. Cutting Blade
7. Blade Guard
8. Battery Seating
9. Guide Wheel
10. Motor Housing
11. Depth Adjustment Lever
12. Depth Adjustment Wheel
ACCESSORIES
13. Blade Pin 14. Blade Spanner
2. Slide the shaft lock over the collar onto the
threaded section and screw tight.
56 7
9
13 14
1211
Collar
8
10
3. INSERTING & REMOVING THE BATTERY
2. ADJUSTMENTS
1. Align the ribs of
the battery with
the recess in
the lawn edger
just below the
handle and slide
in until it clicks
into place.
2. To remove,
press and hold
the battery
release tab
and then slide
out.
2. To decrease the
cutting depth
pull the lever
out and move it
down a notch,
towards the
rear.
Adjusting the Cutting Depth
Adjusting the Handle
1. Release the
adjustable handle
lever.
Note: If you are unsure of which cutting height to
use, begin with smallest depth setting 3 - 36.5mm
(shallowest) and complete a trial cut on a small section
of the lawns edge. Re-adjust if necessary.
The lawn edger has a depth adjustment lever to easily
adjust the cutting depth. There are 3 cutting depth
settings; 3 - 36.5mm, 2 - 40mm and 1 - 45mm.
2. Adjust the
handle into
the most
comfortable
position, then
lock in place
with the lever.
3. To increase the
cutting depth
pull the lever
out and move
it up a notch,
towards the
front of the
unit.
1. Remove the battery pack.
4. Refit the battery pack.
Run Time
The operating time of the PXC battery (the area that
can be covered with a single battery charge) is largely
dependent on the state of the grass (e.g. Density,
moisture, thickness, etc.) the lawn edger cutting depth
position and your walking speed (rate of work).
Frequently turning the equipment on and off while
edging will also reduce the amount runtime and
area that you can covered. If the operating time of
the PXC battery (runtime and area coverage) is still
unsatisfactory in spite of the above measures, you can
remedy the problem by using PXC battery with a larger
capacity (Ah).
WARNING! BEFORE USING, ALWAYS VISUALLY INSPECT
TO SEE THAT THE BLADE, BLADE BOLT AND CUTTER
ASSEMBLY ARE NOT WORN OR DAMAGED.


Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: PXLEK-1840

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXLEK-1840 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Ozito

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd