Ozito PXSMSS-036 Handleiding

Ozito Niet gecategoriseerd PXSMSS-036

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXSMSS-036 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
STANDARD EQUIPMENT
PXSMSS-036
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 2 x 18V
No Load Speed: 3,800/min
Blade: Ø210 x Ø30 x 1.8mm (40T)
Mitre Angle: 0-45° Left & Right
Bevel Angle: 0-45° Left
Cutting Capacity:
Mitre 0° x Bevel 0°: 65 x 310mm
Mitre 45° x Bevel 0°: 65 x 210mm
Mitre 0° x Bevel 45°: 35 x 310mm
Mitre 45° x Bevel 45°: 35 x 210mm;
Weight: 12.5kg
ozito.com.au
0922
Ø210mm Sliding Compound
Mitre Saw
2 x Extension Tables, Table
Handle & Carry Handle
Dust Bag, Material Clamp &
Combination Key
Ø210MM SLIDING
COMPOUND
MITRE SAW
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
O F F
This tool is compatible with all batteries & chargers from the Ozito PXC range.
For optimal performance, we recommend the use of a 3.0Ah batteries or higher to
operate this PXC Mitre Saw.
CORDLESS SLIDING MITRE SAW
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
Note: The combination key is located inside the slot on the slide bar
at the back of the unit, and can be used for assembly. Make sure the
correct extension table is used for left & right sides respectively. Ensure
the extension tables are installed correctly, and always use the extension
tables during operation.
1. Remove the screw from the bar of the extension table.
2. Press and hold the lever located
inside the extension table handle
and slide the bars into the slots on
the unit. The notched bar should be
inserted through the bracket on the
underside of the unit.
3. Replace and tighten the screw.
4. Repeat steps 1, 2 & 3 for the other extension table.
5. Align the table handle with the bar on the
mitre table and screw it into place.
6. Press the end cap into the table handle.
7. Remove the screws on the top of the unit.
8. Align the holes in the carry handle
with the screw holes and then
replace the screws to attach the
carry handle.
9. Squeeze the clamp at the end of the
dust bag and place it over the dust
extraction port.
Note: The dust extraction port can block easily
with dust and requires to be periodically cleaned.
For more efcient operation, empty the
dust bag when it is no more than half full.
This allows better air ow through the bag.
Dust bags will not collect all the saw dust
generated by the mitre saw. For best results
a dust extractor should be used in place of
the dust bag.
9. Hold down the cutting head and pull the lock down pin to release the
cutting head from its transport position.
HOLD
DOWN
WARNING! ENSURE THE TOOL IS TURNED OFF
AND DISCONNECTED FROM THE POWER SUPPLY
BEFORE PERFORMING ANY OF THE FOLLOWING
OPERATIONS.
1716 18 19
13
20
4
1
2
3
5
6
8
9
7
25
23
22
21
24
12
15
14
11
10
27
26
28
1. Battery Seating
2. Laser On/Off Switch
3. Lock-Off Lever
4. Spindle Lock Button
5. Lock Down Pin
6. Material Clamp
7. Fence
8. Table Insert
9. Table Lock
10. Table Handle
11. Mitre Angle Pointer
12. Mitre Table
13. Worklight & Laser
14. On/Off Trigger
15. Worklight On/Off Switch
16. Combination Key Storage
17. Slide Lock
18. Dust Bag
19. Slide Bar
20. Carry Handle
21. Cutting Handle
22. Saw Blade
23. Trenching Depth Screw
24. Retractable Blade Guard
25. Mounting Point
26. Extension Table Handle
27. Material Stop
28. Bevel lock
Bevel Angle Adjustment
WARNING! MOVE THE MATERIAL CLAMP TO THE
OPPOSITE SIDE OF THE BEVEL DIRECTION. THIS
ALLOWS THE CUTTING HEAD TO TILT THE FULL 45°.
1. Loosen the bevel lock.
2. Tilt the cutting head leftward to the desired bevel
angle.
3. Tighten the bevel lock to lock the angle in place.
Trenching
Trenching refers to restricting the depth of cut and permits a “trench” to be
cut in the workpiece.
1. Ensure the cutting head is raised and the nut on the
trenching depth screw is loosened.
2. Adjust the trenching depth screw to the desired depth.
Note: It is recommended to test the depth set is correct
on a scrap piece of wood.
3. To check that the blade stops at the desired
position, lower the cutting head until the
trenching stop adjustment screw touches the
trenching stop.
4. When the correct depth is set, tighten the nut
to lock the position.
Material Clamp
1. Loosen the clamp locking knobs and insert the
shaft into the hole.
2. Adjust the material clamp into the desired
location and tighten all locking knobs.
3. The large screw can be lowered onto the timber
workpiece in order to secure the workpiece while
performing a cut.
Note: The clamp can be mounted on either side of the blade. When
performing bevel cuts, the work clamp must be on the opposite side of the
bevel.
WARNING! ENSURE THE MATERIAL IS SECURELY
CLAMPED BEFORE MAKING ANY CUTS. FAILURE
TO SECURE THE MATERIAL MAY CAUSE THE
WORKPIECE TO FLY OFF AND CAUSE PERSONAL
INJURY. MINIMUM WORKPIECE LENGTH: 160MM.
Securing The Mitre Saw
The base of the saw has four
mounting holes (1 in each corner)
that can be used to mount it to a
workbench or mitre saw stand. Use
four bolts (not included) to secure
it in place. Ensure that the mitre
saw is always stable and secure
during use.
Slide Lock
When cutting a narrow piece of wood it is not
necessary to use the slide mechanism. In these
circumstances, push back the cutting head and
ensure the slide lock is tight to prevent the cutting
head from sliding.
Mitre Angle Adjustments
WARNING! ENSURE THE MITRE TABLE LOCK AND
THE BEVEL LOCK ARE TIGHT BEFORE MAKING A
CUT. FAILURE TO DO SO MAY RESULT IN THE MITRE
TABLE OR THE CUTTING HEAD MOVING DURING
OPERATION & CAUSE SERIOUS PERSONAL INJURY.
WARNING! ENSURE THE FENCE AND MATERIAL
CLAMP ARE ADJUSTED FOR BLADE CLEARANCE
BEFORE MAKING A CUT.
1. Loosen the table handle by rotating it anti-
clockwise.
2. Push down and hold the table lock button,
then shift the mitre table to the desired mitre
angle (left or right) as shown by the mitre angle
pointer
Note: The mitre table features positive click stops
at 0°, 15°, 22.5°, 31.6° and 45° for quick setting of
common mitre angles.
3. Tighten mitre table lock at selected angle.
Spindle Lock
WARNING! NEVER PRESS WHEN BLADE IS
ROTATING.
The spindle lock prevents the blade in the saw from
rotating. Depress and hold the spindle lock while
installing, changing, or removing the blade.
2. ADJUSTMENTS
a.
b.

Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: PXSMSS-036

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXSMSS-036 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Ozito

Ozito

Ozito PXLEK-1840 Handleiding

2 November 2024
Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024
Ozito

Ozito PXNGS-218 Handleiding

8 April 2024
Ozito

Ozito PXHTBK-2518 Handleiding

8 April 2024
Ozito

Ozito PSR-5732U Handleiding

16 Maart 2024
Ozito

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024
Ozito

Ozito PXWBS-200U Handleiding

16 Maart 2024
Ozito

Ozito PXDDK-301U Handleiding

16 Maart 2024
Ozito

Ozito PXCPPS-018U Handleiding

16 Maart 2024
Ozito

Ozito WPHGK-2000U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024