Ozito PXSBK-418 Handleiding

Ozito Niet gecategoriseerd PXSBK-418

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXSBK-418 (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/12
SPECIFICATIONS
Input: 18V
No Load Speed: 800-1,400/min
Brush Diameter Max.: 115mm
Working Width Max.: 215mm
Max. Inlet Pressure: 87 psi (6 bar)
Max. Water Inlet Temp.: 35 C°
Noise Rating: 94.6dB (A)
IP Rating: IPX0
Tool Weight: 4.1kg
STANDARD EQUIPMENT
Surface Brush
SURFACE
BRUSH
INSTRUCTION MANUAL
ozito.com.au
Additional Handle
Soft 2-Piece Nylon Brush & Cover
Hose Clip, Water Control Valve
Medium 2-Piece Nylon Brush
PXSBS-018
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
0321
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way
• Professional, industrial or high frequency use.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty Warranty excludes consumable parts, for example: and included
accessories.
KNOW YOUR PRODUCT SETUP & PREPARATION
1. ASSEMBLY
1. Water Inlet Connector
2. Motor Housing
3. Hose Clip
4. Telescopic Shaft
5. Additional Handle
6. Speed Controller
7. Rear Handle
8. Battery Seating
9. On/Off Trigger
10. Forward/Reverse Switch
11. Knob
12. Nylon Brush
13. Brush Cover
14. Splash Guard
15. Shaft Collar
SURFACE BRUSH
1234567
8
BATTERY & CHARGER
This tool is compatible with all battery and chargers from the Ozito
Power X Change Range.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
10
11
9
WARNING!: ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY DISCONNECTED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
Fitting the Additional Handle
For transport reasons the Main Handle is at 90 to the brush housing. To °
ensure that you have a comfortable working position, the main handle must
be aligned with the brush housing and the length of the Telescopic Shaft can
be adjusted.
1. Unscrew the two knobs on the
handle and separate the handle
from the bracket.
2. Place the top half in position and
secure in place with the bracket
on the underside and the two
knobs.
3. Tighten the two knobs to hold the
additional handle in position.
Note: To adjust the position, simple loosen the two knobs sufciently to
allow handle adjustment into the desired position, then tighten the two knobs
to secure in place.
1. Turn the Lock Nut anti-clockwise
to loosen and turn the Main
Handle 90 into alignment with °
the brush housing.
2. To change the working height,
extended the Telescopic Shaft
to the desired height and then
retighten the Lock Nut by turning
it clockwise.
12 13 14 15
Adjusting the Working Height
2. CLEANING BRUSHES
2. The Medium Nylon Brush
(black) is supplied with a side
brush. Each of the brushes
have Rubber Caps on the
outside.
3. Slot the nylon brush with
side brush onto the brush
mount on either the left or
right side according to your
requirements and the other
nylon brush onto the other
brush mount.
1. Remove Brush Covers from each
end of the brush housing.
Fitting and Removing the Cleaning Brushes
Use only the brush which is intended to be used for the surface you want to
clean. Test the brush for suitability on an inconspicuous area rst before using
it each time. Different brushes for different surfaces are available as separate
accessories. Only use water without any additives whatsoever.
Note: Worn or frayed brushes should be replaced in good time. Replace the
brush as soon as its diameter is less than approx. 95 mm. A brush diameter of
any less can lead to damage.
• Medium Nylon Brush - Black
This brush is specically suitable for cleaning unsealed paver and stone
surfaces. It can therefore also be used for cleaning surfaces which are paved
with paving stones/concrete blocks or concreted surfaces (e.g. driveways,
decks, paths). The side brush can be used for cleaning perimeters and bases.
Diameter: 115mm. Working width: 215mm
Cleaning smooth, unsealed paver and stone surfaces
• Brush in a forward direction only, standard direction of rotation.
• In case of certain kinds of stubborn dirt, it can be helpful to clean using
both directions of rotation. Please note that when the equipment is in
reverse, it has less power.
• To clean perimeters and bases, remove the wide side cover and clean them
using the side brush.
• Afterwards, rinse the cleaned surface down with water.
• Soft Nylon Brush - Yellow/Green
This brush also be used for cleaning wood, composite materials such as
Bamboo Plastic Composite (BPC) and Wood Plastic Composite (WPC) or for
brushing (e.g. attened areas) articial turf to raise it upright, as used in the
home where it is installed, for example, on balconies or decks.
Diameter: 115mm. Working width: 195mm
Cleaning wood, composite materials(BPC/WPC)
• Always clean the boards or wooden elements in a longitudinal direction
(along the grain).
• Brush in a forward direction only, standard direction of rotation.
• It is recommended that you clean on a board-by-board basis.
• Afterwards, rinse the cleaned surface down with water.
Brushing articial turf
• Do not use water - dry-brush only.
• Brush in a forward direction only, standard direction of rotation.
• Remove all leaves, rubbish and similar before starting brushing.
WARNING!: ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY DISCONNECTED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
• Ultra Metal Brush (accessory)
This brush can be used for cleaning robust surfaces such as, e.g. paving
stones/ concrete blocks, concreted surfaces, granite or porphyry to remove
stubborn dirt.
Rough, unsealed paving stones, concrete blocks and
concrete surfaces
• Brush in a forward direction only, standard direction of rotation.
• In case of certain kinds of stubborn dirt, it can be helpful to clean using both
directions of rotation. Please note that when the equipment is in reverse, it
has less power. Afterwards, rinse the cleaned surface down with water.
• Not suitable for polished, ground or sealed natural/articial stone surfaces.
WARNING!: THE SURFACES MUST BE SUITABLE FOR
CLEANING USING ROTATING BRUSHES. FOR WET
CLEANING THE SURFACES MUST ALSO BE INSENSITIVE
TO WATER.
WARNING!: SENSITIVE, POLISHED, COATED AND
SCRATCH-SENSITIVE SURFACES CAN BECOME
ROUGHENED AND/OR GET DAMAGED. THIS EQUIPMENT
MUST NOT BE USED TO CLEAN SUCH SURFACES.
WARNING!: THERE IS A RISK OF INJURY FROM THE
BRISTLES - WEAR SAFETY GLOVES.
WARNING!: THERE IS A RISK OF INJURY FROM THE
BRISTLES - WEAR SAFETY GLOVES.

Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: PXSBK-418

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXSBK-418 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Ozito

Ozito

Ozito PXLEK-1840 Handleiding

2 November 2024
Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024
Ozito

Ozito PXNGS-218 Handleiding

8 April 2024
Ozito

Ozito PXHTBK-2518 Handleiding

8 April 2024
Ozito

Ozito PSR-5732U Handleiding

16 Maart 2024
Ozito

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024
Ozito

Ozito PXWBS-200U Handleiding

16 Maart 2024
Ozito

Ozito PXDDK-301U Handleiding

16 Maart 2024
Ozito

Ozito PXCPPS-018U Handleiding

16 Maart 2024
Ozito

Ozito WPHGK-2000U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024