Ozito PXMFTS-100 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXMFTS-100 (6 pagina's) in de categorie Multitool. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/6
SPECIFICATIONS
Voltage: 18V
No Load Speed: 11,000-20,000/min
Orbit Angle: 3.2°
Sanding Pad Size: 90 x 90 x 90mm
Sandpaper Size: 93 x 93 x 93mm
Weight: 1.18kg
MULTI FUNCTION
TOOL
INSTRUCTION MANUAL
ozito.com.au
STANDARD EQUIPMENT
Multi Function Tool
Accessories
PXMFTS-100
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
0318
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts, for example: cutting blades.
WOOD M ET AL
1. FITTING THE BATTERY
Inserting & Removing the Battery
1 Slide the battery into the seating
at the back of the tool until it
clicks into place.
2 To remove, press and
hold the battery release
tab and then slide out.
ab
WOOD METAL
KNOW YOUR PRODUCT SETUP & PREPARATION
CORDLESS MULTI FUNCTION TOOL
ACCESSORIES
1 2 3 4
65
7 8 9 10 11 12 13
1 Accessory Locking Lever
2 On/Off Switch
3 Variable Speed Dial
4 Battery Seating
5 Accessory Drive Spindle
6 Sure Grip Handle
7 Sanding Pad
8 Sanding Paper
(3 x 60grit, 3 x 80grit, 3 x 120grit)
9 Wood Plunge Blade
10 Metal Plunge Blade
11 Semi-Circular Blade
12 Scraper
13 Accessory Adapter
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
BATTERY & CHARGER
This tool is compatible with all batteries and chargers from the Ozito
Power X Change Range.
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure a long service
life.
The output power automatically cuts off during operation when the tool and/or battery are
placed under the following situations:
• When the tool is overloaded:
If this occurs, release the trigger switch and remove causes of overload, then pull the
switch trigger again to restart.
• When the remaining battery capacity becomes low:
Recharge the battery pack.
Note: The battery protection system does not in any way damage the tool.
Note: The indicated capacity may be lower than the actual level during use or immediately
after using the tool.
To absorb the vibrations which arise
on the rechargeable battery, there
is some play between the battery
and the tool’s battery seating. This
is normal and has no effect on the
performance of the equipment or the
rechargeable battery
Vibration Absorption
3. CONTROLS
WARNING! AFTER USE, HOLD THE TOOL AWAY FROM
YOUR BODY UNTIL THE SPINDLE STOPS COMPLETELY.
Turning On and Off
Variable Speed Control
1 To start the tool press the on/
off switch forward into the on
position.
1 To increase the speed of the tool,
rotate the variable speed dial to
a higher number.
2 To decrease the speed of the
tool, rotate the variable speed
dial to a lower number.
2 To stop the tool press the on/
off switch backward into the off
position.
WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
THE BATTERY IS REMOVED BEFORE PERFORMING ANY
OF THE FOLLOWING TASKS.
2. FITTING ACCESSORIES
WARNING! KEEP FINGERS CLEAR OF SPINDLE WHEN
SECURING THE ACCESSORY TO AVOID PINCHING.
Attaching Accessories
Removing Accessories
2 Place the desired
accessory onto the
accessory drive
spindle ensuring
the holes in the
accessory align with
the notches on the
tool.
4 Rotate the
accessory locking
lever clockwise
to secure the
accessory.
Note: Pull on the
accessory to check if it
is secured correctly.
1 To remove the
accessory rotate
the locking lever
anti-clockwise and
then remove from
the spindle.
1 Rotate the accessory locking
lever anti-clockwise to open
spindle tment.
3 When using other non-Ozito
multi function tool compatible
accessories, the accessory
adapter may need to be tted to
secure correctly.
Product specificaties
| Merk: | Ozito |
| Categorie: | Multitool |
| Model: | PXMFTS-100 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito PXMFTS-100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Multitool Ozito
23 Augustus 2024
30 Juli 2024
14 Juni 2023
9 Juni 2023
6 Juni 2023
15 Mei 2023
3 Mei 2023
3 Mei 2023
21 April 2023
14 April 2023
Handleiding Multitool
- Multitool Bosch
- Multitool AEG
- Multitool DeWalt
- Multitool Bavaria
- Multitool Dremel
- Multitool Einhell
- Multitool Extech
- Multitool Fein
- Multitool Ferm
- Multitool Festool
- Multitool Gamma
- Multitool Gude
- Multitool Hama
- Multitool Hikoki
- Multitool Kress
- Multitool Makita
- Multitool Metabo
- Multitool Milwaukee
- Multitool Parkside
- Multitool Powerfix
- Multitool Powerplus
- Multitool Renovator
- Multitool Robust
- Multitool Rocktrail
- Multitool Ryobi
- Multitool Silvercrest
- Multitool Silverline
- Multitool Skil
- Multitool Stiga
- Multitool Taurus
- Multitool Toolcraft
- Multitool Topcraft
- Multitool Trotec
- Multitool Varo
- Multitool Vonroc
- Multitool Westfalia
- Multitool Workzone
- Multitool Worx
- Multitool Black And Decker
- Multitool Cocraft
- Multitool Meec Tools
- Multitool Hilti
- Multitool Cotech
- Multitool Fieldmann
- Multitool Lezyne
- Multitool Proxxon
- Multitool Porter-Cable
- Multitool EGO
- Multitool Leatherman
- Multitool Dedra
- Multitool Graphite
- Multitool RIDGID
- Multitool Craftsman
- Multitool Alpha Tools
- Multitool G-Technology
- Multitool SKS
- Multitool Baumr-AG
- Multitool MTM
- Multitool Powerblade
- Multitool Meister Craft
- Multitool McKenzie
- Multitool Ergotools Pattfield
- Multitool CMT Orange Tools
- Multitool Donau Elektronik
Nieuwste handleidingen voor Multitool
10 December 2024
8 December 2024
4 December 2024
17 November 2024
17 November 2024
14 November 2024
20 Oktober 2024
10 Juli 2024
9 Juni 2024
9 Juni 2024