Ozito MFR-2200U Handleiding

Ozito Multitool MFR-2200U

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito MFR-2200U (2 pagina's) in de categorie Multitool. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

WHAT’S IN THE BOX

MAINTENANCE

TROUBLESHOOTINGOPERATION ELECTRICAL SAFETY

DESCRIPTION OF SYMBOLS

• Keep the ventilation vents of the multi function tool clean at all times,

if possible, prevent foreign matter from entering the vents.

• After each use, blow air through the multi function tool housing to ensure it is

free from all dust particles which may build up. Build up of dust particles may

cause the tool to overheat and fail.

• If the enclosure of the multi function tool requires cleaning, do not use

solvents but a moist soft cloth only. Never let any liquid get inside the multi

function tool; never immerse any part of the multi function tool into a liquid.

Carbon Brushes

When the carbon brushes wear out, the multi function tool will spark and/

or stop. Discontinue use as soon as this happens. They should be replaced

prior to recommencing use of the multi function tool.

Carbon brushes are a wearing component of the

tool and therefore are not covered under warranty.

Continuing to use the multi function tool when carbon

brushes need to be replaced may cause permanent

damage. Carbon brushes will wear out after many

uses but when the carbon brushes need to be

replaced, take the multi function tool to an electrician

or a power tool repairer for a quick and low cost replacement. Always replace

both carbon brushes at the same time.

Note: Ozito Industries will not be responsible for any damage or injuries caused

by the repair of the multi function tool by an unauthorised person

or by mishandling of the multi function tool.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents.

This is normal and does not indicate a problem.

Excessive sparking visible through the housing air vents

and/or the multi function tool failing to operate

May indicate the carbon brushes have worn out and need to be

replaced. Carbon brushes should only be replaced by a qualied

electrician or power tool repairer.

MULTI FUNCTION TOOL SAFETY INSTRUCTIONS

Before you connect the equipment to the mains supply make sure that the data on the rating plate are

identical to the mains data.

This tool is double insulated therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician

or a power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool.

The insulation system is for added protection against injury resulting from a possible electrical insulation

failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the

extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead

not suitable for the power input of the tool or which is damaged or defective may result in a risk of re

and electric shock.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING!

• This tool may only be used for dry grinding/sanding operations.

• Always guide the power cable away from the back of the tool.

• Use of the tool on materials containing asbestos is prohibited.

• Always remove the plug from the power supply socket before carrying out any work on the machine

(cleaning the sander, changing the sandpaper, etc.).

• Always disconnect the machine by removing the plug from the socket, not by pulling on the power

cable.

• Keep your workplace clean and well illuminated.

• Make sure that the workpiece is su󰀩ciently secured so that it cannot slip.

• Keep children away.

• For your own sake, keep the machine clean at all times and check it for signs of damage each time

after using it.

• Make sure that the switch is set to OFF before you insert the plug into the power supply socket.

• Make sure of your footing, particularly when working on ladders and platforms.

• Harmful or toxic dust can be produced when working on wood or metal.

Touching or inhaling this dust can be harmful for the operator and other persons nearby.

• To protect your health, always wear safety goggles and a dust mask during sanding/grinding work!

• If you discover any damage to the machine, use the exploded diagram and the spare parts list to

determine which parts need to be ordered from Customer Service.

• Important! Wear safety goggles and a dust mask.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety. Children should be

supervised to ensure that they do not play with the appliance.

Do not lose these safety instructions.

MULTI

FUNCTION

TOOL

300W

ORIGINAL INSTRUCTIONS

SPECIFICATIONS

Motor: 300W

Input: 230-240V ~ 50Hz

No Load Speed: 15,000-21,000 opm

Orbit Angle: 3.2°

Sanding Pad Size: 92 x 92 x 92mm

Weight: 1.43kg

MFR-2200U

ozito-diy.co.uk

Multi Function Tool

Sanding Pad & Paper x 15

Dust Collection

Accessory

Scraper & Triangular

Rasp

Straight Blade x 2

Semi Circular Blade

Grout Removal Disc

WARNING: BEFORE CARRYING OUT ANY MAINTENANCE

PROCEDURES, ENSURE THE TOOL IS SWITCHED OFF

AND DISCONNECTED FROM THE POWER SUPPLY.

VVolts Hz Hertz

~Alternating current WWatts

/min Revolutions or

reciprocation per minute

Double insulated

no No load speed

Warning

Read instruction manual

WARRANTY

iSC GmbH · Eschenstraße 6 · 94405 Landau /Isar · Germany 0616

All of our products undergo strict quality checks to ensure that they reach

you in perfect condition. In the unlikely event that your device develops a

fault, please contact our service department at the address shown on this

guarantee card. You can also contact us by telephone using the customer

service number shown. Please note the following terms under which

guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the

manufacturer mentioned below promises to buyers of its new products

in addition to their statutory guarantee claims are not a󰀨ected by this

guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or

manufacturing faults on a product which you have bought from the

manufacturer mentioned below are limited to either the rectication of said

defects on the product or the replacement of the product, whichever we

prefer.

Please note that our devices are not designed for use in commercial, trade

or professional applications. A guarantee contract will not be created if the

device has been used by commercial, trade or industrial business or has

been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly

instructions or due to incorrect installation, a failure to follow the operating

instructions (for example connecting it to an incorrect mains voltage or

current type) or a failure to follow the maintenance and safety instructions

or by exposing the device to abnormal environmental conditions or by lack

of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example

overloading the device or the use or unapproved tools or accessories),

ingress of foreign bodies into the device (such as sand, stones or dust,

transport damage), the use of force or damage caused by external forces

(for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural

wear or tear or by normal use of the device.

4. Your Product is guaranteed for a period of 36 months from the original

date of purchase and is intended for DIY (Do It Yourself) use only. Lithium

Ion batteries and chargers are covered by a 12 month warranty. Warranty

excludes consumable parts, for example: carbon brushes, blades, sanding

paper, etc. Guarantee claims should be submitted before the end of

the guarantee period within two weeks of the defect being noticed. No

guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if

repairs are carried out or parts are replaced. In such cases, the work

performed or parts tted will not result in an extension of the guarantee

period, and no new guarantee will become active for the work performed or

parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST

RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR

Please refer to the restrictions of this warranty concerning wearing parts,

consumables and missing parts as set out in the service information in

these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

5. SCRAPING

1. Turn multi function

tool on and select

appropriate speed.

2. Place multi function tool on the workpiece at an angle of

approximately 10-15 .°

3. Allow the scraper to do the work; do not apply heavy pressure

to the multi function tool. This may cause the multi function

tool to overload or cut into the surface of the workpiece.

10 - 15 º

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk

at your local Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: enquires@ozito-diy.co.uk

WARNING! Read all the safety information, instructions, illustrations and technical data

provided on or with this power tool. Failure to adhere to the following instructions may result in

electric shock, re and/or serious injury.

Keep all the safety information and instructions in a safe place for future use.

The term „power tool“ used in the safety information and instructions refers to power tools operated

from the mains power supply (with a power cable) and to battery operated power tools (without a

power cable).

1. Workplace safety

a) Keep your work area clean and well lit. Untidy or unlit work areas can result in accidents.

b) Do not use this power tool in an area where there is a risk of explosion and where there are

inammable liquids, gases or dust. Power tools generate sparks that can ignite dust or vapors.

c) Keep children and other people away from the power tool while you are using it. If you are

distracted you may lose control of the power tool.

2. Electrical safety

a) The plug on the power tool must t into the socket. The socket must not be modied in any way. Do

not use adapter plugs together with power tools with a protective earth. Unmodied plugs and matching

sockets will reduce the risk of an electric shock.

b) Avoid body contact with earthed surfaces such as pipes, heating systems, stoves and

refrigerators. There is an increased risk of su󰀨ering an electric shock if your body is earthed.

c) Keep the power tool out of the rain and away from moisture. The ingress of water into an electric

power tool increases the risk of an electric shock.

d) Do not use the power cable for a purpose for which it is not designed, for example to carry the

power tool, hang it up or to pull the plug out of the socket. Keep the power cable away from heat,

oil, sharp edges and moving parts. Power cables that are damaged or tangled increase the risk of an

electric shock.

e) If you use an electric power tool outdoors, use only extension cables that are suitable for outdoor

use. The use of an extension cable which is suitable for outdoor use reduces the risk of an electric

shock.

f) If you cannot avoid using the power tool in a damp location, use a residual current device

(RCD) circuit breaker. The use of a residual current device (RCD) circuit breaker will reduce the risk of

su󰀨ering an electric shock.

3. Safety of persons

a) Be careful, watch what you are doing and be sensible and responsible when using an electric

power tool. Never use the power tool if you are tired or under the inuence of drugs, alcohol or

medication. One moment of inattention when using the electric tool can result in serious injuries.

b) Wear personal safety equipment and always wear safety goggles. Wearing personal safety

equipment such as dust masks, non-slip safety shoes, a helmet or ear plugs, depending on the type and

application of the tool, reduces the risk of injury.

c) Make sure that the tool cannot start up accidentally. Ensure that the power tool is switched o󰀨 before

you connect it to the power supply and/or connect the battery pack, pick it up or carry it. If you have your

nger on the switch while carrying the power tool or if you connect the power tool to the power supply

while it is switched on, this may cause accidents.

d) Remove all adjusting tools or wrenches before you switch on the power tool. Any tool or wrench in

a rotating part of the power tool could cause injuries.

e) Avoid abnormal working postures. Make sure you stand squarely and keep your balance at all times.

This will enable you to control the power tool better in unexpected situations.

f) Wear suitable clothes. Never wear loose tting clothes or jewelry. Keep hair and clothing away from

moving parts. Loose clothing, jewelry or long hair can be caught by moving parts.

g) If dust extraction devices and dust collection devices can be tted, they must be connected and

must be used correctly. The use of a dust extractor can reduce the dangers posed by dust.

h) Do not allow yourself to be lulled into a false sense of security and do not ignore the safety

regulations covering electric power tools, even if you are familiar with the power tool after having

used it many times. Carelessness can lead to serious injuries in just a fraction of a second.

4. Using and handling the power tool

a) Do not overload your power tool. Use the correct electric tool for the job in hand. The correct tool will

enable you to work better and more safely within the specic performance range.

b) Do not use an electric power tool if the switch is defective. An electric power tool that cannot be

switched on or o󰀨 is dangerous and must be repaired.

c) Pull the plug out of the socket and/or remove the removable battery pack before making any

adjustments to the tool, changing plug-in tool parts or putting the power tool down. These

precautions will prevent the power tool starting accidentally.

d) Keep unused electric tools out of the reach of children. Do not allow people who are not familiar

with the power tool or who have not read these instructions to use the power tool. Electric tools are

dangerous if they are used by inexperienced people.

e) Look after power tools and plug-in tools with care. Check that moving parts function correctly and do

not jam, and whether any parts are broken or damaged such that they adversely a󰀨ect the function of the

power tool. Have damaged parts repaired before you use the power tool. Many accidents are caused by

poorly maintained electric tools.

f) Keep cutting tools sharp and clean. Carefully maintained cutting tools with sharp cutting edges will

jam less and are easier to control.

g) Use the power tool, plug-in tools, etc. as set out in these instructions. Take account of the

conditions in your work area and the job in hand. Using electric tools for purposes other than the one for

which they are designed can result in dangerous situations.

h) Keep the handles and grip surfaces dry, clean and free from oil and grease. If the handles and grip

surfaces are slippery, it will not be possible to operate and control the power tool safely in unforeseen

situations.

5. Service

a) Have your power tool repaired only by trained personnel using only genuine spare parts. This will

ensure that your power tool remains safe to use.

Anleitung_MFR-2200U.indd 1-3

Anleitung_MFR-2200U.indd 1-3Anleitung_MFR-2200U.indd 1-3 12.12.2019 10:46:46

12.12.2019 10:46:46

12.12.2019 10:46:4612.12.2019 10:46:46

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

KNOW YOUR PRODUCT

MFR-2200U

SETUP & PREPARATION OPERATION

1. Accessory Drive Spindle

2. Side Handle

3. On/O󰀨 Switch

4. Rear Handle

5. Variable Speed Dial

MULTI FUNCTION TOOL

6. Semi Circular Blade

(Wood, Plastic & Metal)

7. Straight Blade x 2

(Wood & Plastic)

8. Scraper

9. Triangular Rasp

10. Grout Removal Disc

11. Sanding Pad

12. Sanding Paper

P60 Grit x 5

P120 Grit x 5

P240 Grit x 5

13. Hex Key

14. Locking Bolt

15. Washer

16. Dust Collection Accessory

ACCESSORIES

1. ASSEMBLY 2. CONTROLS 3. SANDING 4.

SAWING

2. To turn o󰀨, slide the

switch backwards.

2. Place the circular end of the dust collection adaptor over the

accessory spindle so that the adaptor rests against the bottom

of the tool handle. Push the securing clip over the power cord

to secure in place.

3. Connect a vacuum or dust extractor hose to the hose

connector.

1. To turn on, slide the

on/ o󰀨 switch forward.

1. Push the parts of the dust collection accessory together.

The dust collection adaptor can be tted to your multi function

tool to reduce the build up of dust and debris while operating.

Accessories must be removed prior to tting the dust collection

accessory. On / O󰀨 Switch

Fitting the Dust Collection Accessory

Variable Speed

For various applications, you will need to select the appropriate

speed for the task.

1. Turn multi function tool on.

2. Scroll through variable

speed dial to desired speed

setting.

Note: The higher the number on the variable speed dial the

faster the oscillation frequency of the multi function tool.

1. Turn multi function tool

on and select appropriate

speed.

2. Place the multi function tool

at on the workpiece.

Note: Do not apply heavy pressure to the tool or tilt the sanding

base as this will wear out the sanding paper and may damage the

sanding pad.

Changing Sanding Paper

2. Peel paper o󰀨 pad from one

of the corners.

1. Align paper to pad and

press rmly to attach.

Semi Circular & Straight Blade

2. Turn multi function tool on

and select speed.

1. Ensure the workpiece

is securely held down.

3. Use slight pendulum

motion when plunge

cutting.

Note: Ensure blades are not blunt or damaged in any way

before commencing application.

Grout Removal Disc

1. Turn the multi function tool

on and select speed.

Triangular Rasp

1. Turn multi function tool

on and select appropriate

speed.

2. Place the multi function tool

at on the workpiece.

This accessory is suitable when sanding materials which require

a large amount of material removal, for example: rough wood,

mortar or adhesive cement / concrete.

2. Use slight pendulum

motion when cutting.

Note: Periodically turn the unit o󰀨 and remove any built-up

dust and debris.

Note: Periodically turn the

unit o󰀨 and remove any

built-up dust and debris.

Accessory Fitment

1. Place accessory

over the drive

spindle and

position to suit

angle needed

for application.

Note: Ensure the accessory is sitting at on spindle and locking

pins.

2. Place at side of

accessory tting

washer on the

accessory then insert

locking bolt.

3. Tighten locking

bolt with hex key.

1. Loosen locking bolt with

hex key.

2. Remove bolt and

accessory.

Accessory Removal

Side Handle

The side handle can be tted on either side of the tool. The

correct position will be determined by your preferred hand and the

operation being performed.

Removing

2. Remove the side handle.

Attaching

1. Firmly attach the side

handle in the desired

position.

6 7 8 9 10

11 12 13 14 15 16

2 3 4 5

CAUTION: THE POWER SUPPLY FOR THIS PRODUCT

SHOULD BE PROTECTED BY A RESIDUAL CURRENT

DEVICE (RATED AT 30mA OR LESS).

Anleitung_MFR-2200U.indd 4-6

Anleitung_MFR-2200U.indd 4-6Anleitung_MFR-2200U.indd 4-6 12.12.2019 10:46:47

12.12.2019 10:46:47

12.12.2019 10:46:4712.12.2019 10:46:47

Product specificaties

Merk:	Ozito
Categorie:	Multitool
Model:	MFR-2200U

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito MFR-2200U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Multitool Ozito

Ozito PXPPHTK-258 Handleiding

23 Augustus 2024

Ozito PXGMTK-2536 Handleiding

30 Juli 2024

Ozito PXMFTK-200 Handleiding

14 Juni 2023

Ozito MFR-2200U Handleiding

9 Juni 2023

Ozito PXMFTS-100U Handleiding

6 Juni 2023

Ozito PXCPPHTC-418U Handleiding

15 Mei 2023

Ozito MFR-2200 Handleiding

3 Mei 2023

Ozito PXMFTS-100 Handleiding

3 Mei 2023

Ozito LRTK-036 Handleiding

21 April 2023

Ozito RTR-040 Handleiding

14 April 2023

Handleiding Multitool

Nieuwste handleidingen voor Multitool

Powerblade PC4MT5 Handleiding

10 December 2024

EGO PH1420E Handleiding

8 December 2024

Einhell TE-MG 200 E Handleiding

4 December 2024

Alpha Tools A 180 Handleiding

17 November 2024

EGO MRC2306E Handleiding

17 November 2024

Workzone WZMS 10,8 Li Handleiding

14 November 2024

Vonroc OT505DC Handleiding

20 Oktober 2024

Einhell BT-MG 180/1 Handleiding

10 Juli 2024

DeWalt DCS551 Handleiding

9 Juni 2024

DeWalt DCS353 Handleiding

9 Juni 2024