Ozito PXLTK-4028 Handleiding

Ozito Niet gecategoriseerd PXLTK-4028

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXLTK-4028 (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/12
STANDARD EQUIPMENT
PXLTS-180
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V
No Load Speed: 8,000/min
Cutting Width: 280mm
Cutting Line: 1.6 x 5m max.Ø
Line Feed: Automatic
Noise Rating: 96dB
Weight: 2.65kg
ozito.com.au
0223
Line Trimmer
Safety Guard & Screws
CORDLESS
LINE TRIMMER
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, Victoria 3175, Australia
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts, for example: cutting line.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Blade
1. Edging Guide
2. Tilting Head Lock
3. Rotating Head Lock
4. Additional Handle
5. Adjustable Handle Lock
6. Safety Switch
7. Sure Grip Handle
8. On/Off Trigger
9. Battery Seating
10. Shaft Lock
11. Telescopic Shaft
12. Rotating Head Adjustment
13. Safety Guard
14. Cutter Head
15. Edging Guide Lock
This tool is compatible with all batteries & chargers from the Ozito PXC range.
CORDLESS LINE TRIMMER
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
1 2 3 4 5 6 7
8
9
10
1514
13
WARNING! ENSURE THE LINE TRIMMER IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
Fitting the Safety Guard
1. First adjust the length of the
edging guide to identify the two
locating slots.
2. As you place the safety guard
onto the motor housing one of
the slots MUST align with the
metal pin located under the
edging guide lock on the motor
housing. The safety guard sits
ush up against the motor
housing only when the metal pin
locates within one of the slots.
3. When sitting ush, secure in
place with the four screws
provided.
4. A blade on the underside of the
safety guard automatically cuts
the cutting line to length. It is
provided with a safety cover.
Remove the safety cover before
starting work.
WARNING! NEVER USE THE LINE TRIMMER UNLESS
THE SAFETY GUARD IS PROPERLY FITTED.
12
11
WARNING! ALWAYS USE GLOVES WHEN HANDLING
THE BLADE. SHARP EDGES COULD CAUSE INJURY.
2. ADJUSTMENTS
Adjusting the Additional Handle
Adjusting the Working Height
1. Loosen the shaft lock by turning
clockwise to the open position.
2. Adjust the telescopic shaft up
or down to the required working
height.
3. Tighten the shaft lock by turning
anti-clockwise to the lock
position to secure in position.
Adjusting the Tilting Angle
1. Depress the tilting head lock to
allow the handle to tilt.
2. Set the handle to the required
angle. To x the angle of tilt,
release the button and allow the
handle to lock into one of three
available positions.
WARNING! TO PREVENT PERSONAL INJURY OR
DAMAGE TO THE LINE TRIMMER ENSURE THE TILTING
ANGLE IS LOCKED IN ONE OF THE THREE POSITIONS
BEFORE OPERATING.
Adjusting the Edging Guide
Extend the edging guide to prevent the cutting head from getting too close to
an object such as a tree trunk or wall. There are two locking points, minimum or
maximum guide length.
1. With the edging guide locked
in position, depress the edging
guide lock and slide the edging
guide out of lock, then release
the button.
2. Slide the edging guide to the
second locking point.
Adjusting the Rotating Head Position
The line trimmer is tted with a 180 rotating head to allow for edging and °
trimming. To switch between the two, the head must be rotated following the
steps below.
1. Hold the telescopic shaft rmly with one hand and pull the rotating head
adjustment away, out of the rotating head lock
2. Turn the rotating head adjustment 180 anti-clockwise until it latches in °
position.
WARNING! ENSURE THE LINE TRIMMER IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
3. Close the additional handle lock to secure in place.
1. Release the additional handle
lock.
2. Rotate, tilt or slide the handle to
the required position.
WARNING! DO NOT PUT FULL WEIGHT ON THE TILTING
HEAD LOCK.
3. To rotate head to original position repeat step 1 and rotate adjustment 180°
clockwise until it latches in position.

Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: PXLTK-4028

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXLTK-4028 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Ozito

Ozito

Ozito PXLEK-1840 Handleiding

2 November 2024
Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024
Ozito

Ozito PXNGS-218 Handleiding

8 April 2024
Ozito

Ozito PXHTBK-2518 Handleiding

8 April 2024
Ozito

Ozito PSR-5732U Handleiding

16 Maart 2024
Ozito

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024
Ozito

Ozito PXWBS-200U Handleiding

16 Maart 2024
Ozito

Ozito PXDDK-301U Handleiding

16 Maart 2024
Ozito

Ozito PXCPPS-018U Handleiding

16 Maart 2024
Ozito

Ozito WPHGK-2000U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024