Ozito MACK-300 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito MACK-300 (8 pagina's) in de categorie Verfspuit. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
46
8
10
Lb/in²
(PSI)
kPA
(BAR)
PRESSURE GAUGE
kg/cm²
0
25
50
75
100
125
150
0
(1)00
(3)00
(5)00
(7)00
(9)00
2
4 6
8
10
Lb/in²(PSI)kPA(BAR)
PRESSURE GAUGE
kg/cm ²
AIRBRUSH & MINI
COMPRESSOR KIT
3L 105W
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 220–240V ~ 50Hz
Power: 105W
Tank Capacity: 3L
No Load Speed: 1,400/min
Max. Pressure: 4bar (58psi)
Auto Cut-In Pressure: 3bar (43.5psi)
Flow Rate: 15L/min
Weight: 5.32kg
MACK-300
STANDARD EQUIPMENT
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: valve adapters
and accessories.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
3L Mini Air Compressor
Airbrush
1.8m Air Hose, Airbrush Holder &
Spanner
Paint Cup & 2 x Paint Pots
0320
Thinning Paints
Surface preparation and proper paint thinning are the two most
important steps for best results. Ensure all surfaces are free of dust,
dirt and grease.
The airbrush kit comes with a spare
paint pot and lid that can be used for
mixing or thinning the paint until the
desired colour and viscosity is achieved.
Follow the paint manufacturer’s guide
for thinning and mixing ratios. Use
the appropriate thinning agent for paints.
Water based paints can be thinned using water.
1. Before mixing any paint or thinners, work out how much of each
substance is needed.
2. Pour the required amount of
paint into the paint pot.
3. Pour the necessary amount of
thinner into the paint pot.
4. Thoroughly mix the paint and thinning
agent in the paint pot and then attach
the lid securely.
Note: Refer to the troubleshooting section if there are issues with the
paint spread.
Variable Trigger
1. Press and hold the variable trigger down.
This allows air to start owing through the
airbrush.
2. Pull the variable trigger backwards to
allow paint to be sprayed.
Note: The further back the variable
trigger is pulled, the more paint is
sprayed out of the airbrush.
3. Release the variable paint trigger to stop spraying.
Paint Regulator Screw
The paint regulator screw is a stop that holds the variable trigger
backwards. This allows a set amount of paint to be sprayed when the
trigger is depressed.
1. Loosen the regulator screw entirely for
full control over the amount of paint
sprayed.
2. Tighten the regulator screw until the
desired amount of paint is ejected
when the trigger is pressed down.
Note: Always test spray on a scrap piece of material every time an
adjustment is made to the settings.
Paint Pot Vent Hole
The paint pot lid with the intake nozzle
has a vent hole which allows air into
the pot. This enables uid to ow into
the airbrush. Ensure it is clean and not
blocked.
Nozzle Cap
Push the cap over the nozzle of the airbrush
when not in use to protect it.
Note: Avoid rotating the nozzle cap when
removing it, as this may unscrew the nozzle.
2. PAINT PREPARATION 3. AIRBRUSH
OPERATION
PAINT
THINNER
WARNING! THE AIRBRUSH CANNOT BE USED WITH
MATERIALS CONTAINING ABRASIVE SUBSTANCES,
GLAZES, CAUSTIC AND/OR ALKALINE
SUBSTANCES.
Product specificaties
| Merk: | Ozito |
| Categorie: | Verfspuit |
| Model: | MACK-300 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito MACK-300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Verfspuit Ozito
16 November 2024
16 Maart 2024
23 Mei 2023
4 Mei 2023
3 April 2023
29 Maart 2023
8 Maart 2023
24 Februari 2023
2 Februari 2023
15 November 2022
Handleiding Verfspuit
- Verfspuit Bort
- Verfspuit Deco
- Verfspuit Defort
- Verfspuit Easymaxx
- Verfspuit Einhell
- Verfspuit Elektra Beckum
- Verfspuit Ferm
- Verfspuit Holzmann
- Verfspuit Magnum
- Verfspuit Metabo
- Verfspuit Paintmaxx
- Verfspuit Parkside
- Verfspuit Pattfield
- Verfspuit Powerplus
- Verfspuit Silverline
- Verfspuit Wagner
- Verfspuit Westfalia
- Verfspuit Worx
- Verfspuit Jocca
- Verfspuit 3M
- Verfspuit Black And Decker
- Verfspuit Cocraft
- Verfspuit Meec Tools
- Verfspuit Aerotec
- Verfspuit Cotech
- Verfspuit Power Craft
- Verfspuit Truper
- Verfspuit Fieldmann
- Verfspuit Sun Joe
- Verfspuit Probuilder
- Verfspuit MSW
- Verfspuit Birchmeier
- Verfspuit Yato
- Verfspuit Aqua Joe
- Verfspuit Abac
- Verfspuit Meister Craft
- Verfspuit Wagner SprayTech
- Verfspuit Chapin
- Verfspuit XU1
Nieuwste handleidingen voor Verfspuit
16 November 2024
15 November 2024
5 November 2024
15 Oktober 2024
15 Oktober 2024
27 Augustus 2024
27 Augustus 2024
27 Augustus 2024
27 Augustus 2024
7 Augustus 2024