Ozito HGN-2100 Handleiding

Ozito Niet gecategoriseerd HGN-2100

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito HGN-2100 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 195 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landll and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
• Keep the ventilation vents of the heat gun clean at all times, if possible, prevent
foreign matter from entering the vents.
• After each use, blow air through the heat gun housing to ensure it is free from all
dust particles which may build up. Build up of dust particles may cause the heat
gun to overheat and fail.
• If the enclosure of the heat gun requires cleaning, do not use solvents but a
moist soft cloth only. Never let any liquid get inside the heat gun; never immerse
any part of the heat gun into a liquid.
Switch SPHGN2100-05
For spare parts visit www.ozito.com.au
Or contact Ozito customer service
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: enquiries@ozito.com.au
SPARE PARTS
V Volts Hertz Hz
~ Alternating current WWatts
°C Degrees Celsius Read instruction manual
Double insulated Regulator compliance mark
WARNING! This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
WARNING! Are may result if the appliance is not used with care, therefore:
• be careful when using the appliance in places where there are combustible
materials
• do not apply to the same place for a long time
• do not use in the presence of an explosive atmosphere
• be aware that heat may be conducted to combustible materials that are out of
sight
• place the appliance on its stand after use and allow it to cool down before
storage
• do not leave the appliance unattended when it is switched on.
ELECTRICAL SAFETY
WARNING! Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, re and/or serious
injury.
Save all warnings and instructions for future reference. The term “power tool”
in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the
presence of ammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your nger on the switch or energising power tools
that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualied repair person using only
identical replacement parts. This will ensure that the safety of the power tool is
maintained.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! When using mains-powered tools, basic safety precautions, including
the following, should always be followed to reduce risk of re, electric shock,
personal injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an
emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New
Zealand.
This tool is double insulated therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order
to avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this
tool. The insulation system is for added protection against injury resulting from a possible electrical
insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect
the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged
or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension
lead not suitable for the power input of the tool or which is damaged or defective may result in a risk
of re and electric shock.
HEAT GUN SAFETY WARNINGS
HEAT GUN
2000W
INSTRUCTION MANUAL
SPECIFICATIONS
Power: 2000W
Input: 230-240V~50Hz
Airflow: Fan Setting 1: 250 l/min
Fan Setting 2: 500 l/min
Temperature Control: Variable (50-450º/90-600º)
Weight: 0.81kg
HGN-2100
WHAT’S IN THE BOX
Heat Gun
Nozzles x 4
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
Scrapers x 2
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase and is intended for DIY (Do It
Yourself) use only. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: nozzles, scrapers
etc.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
0317

Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: HGN-2100

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito HGN-2100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Ozito

Ozito

Ozito PXLEK-1840 Handleiding

2 November 2024
Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024
Ozito

Ozito PXNGS-218 Handleiding

8 April 2024
Ozito

Ozito PXHTBK-2518 Handleiding

8 April 2024
Ozito

Ozito PSR-5732U Handleiding

16 Maart 2024
Ozito

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024
Ozito

Ozito PXWBS-200U Handleiding

16 Maart 2024
Ozito

Ozito PXDDK-301U Handleiding

16 Maart 2024
Ozito

Ozito PXCPPS-018U Handleiding

16 Maart 2024
Ozito

Ozito WPHGK-2000U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024