Ozito ETL-7530U Handleiding

Ozito Niet gecategoriseerd ETL-7530U

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito ETL-7530U (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
ELECTRIC
TILLER
750W 300mm
ORIGINAL INSTRUCTIONS
SPECIFICATIONS
Voltage: 230V~50Hz
Power Rating: 750W
No Load Speed: 400/min
Working Width: 300mm
Working Depth: 220mm max.
Tines: 4 x 220mm
Noise Level: 93dB(A)
Weight: 8.14kg
ETL-7530U
WHAT’S IN THE BOX
WARRANTY
1117
TILLER SAFETY WARNINGS
• Check all electrical cables for signs of damage or ageing. Replace
the cable if it is cracked, split or otherwise damaged.
• Check the condition of the cutting cylinder, and ensure that all
threaded connections are securely tightened.
• If the tines are blunt, have a power tool repairer inspect the tiller.
Tiller Motor & Switch
Upper & Lower Handle
Once per Season
GENERAL POWER TOOL SAFETY WARNINGS
ELECTRICAL SAFETY
Handle Fasteners
MAINTENANCE
• Lubricate the tines and shaft.
• At the end of the season, have the tiller checked and serviced at a
power tool repairer.
WARNING!: ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
Cleaning
CAUTION!: ENSURE ALWAYS CLEAN THE TILLER AFTER
USE. FAILURE TO CARRY OUT PROPER CLEANING CAN
RESULT IN DAMAGE TO THE TILLER OR CAUSE IT TO
MALFUNCTION.
Whenever possible, clean the tiller straight after you have finished
using it.
• Clean the underside of the housing around the tines, guard shield
and fender with a stiff brush. Then, using a soft cloth dampened
with a mild soap and water mixture wipe the underside. Never
splash with water!
• To remove soil and debris from the tines and transmission, use a
stiff brush or a dampened cloth.
• Clean the motor housing vents, and remove any remaining grass or
dirt.
• Once cleaned, wipe the tine and shaft dry and apply a light coat of
oil.
WARNING!: ENSURE INJURY CAN OCCUR DURING WORK
ON THE TINES. WEAR PROTECTIVE GLOVES.
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the customer
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectication of said
defects on the product or the replacement of the product, whichever we
prefer.
Please note that our devices are not designed for use in commercial, trade
or professional applications. A guarantee contract will not be created if the
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Warranty
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts tted. This also applies if an on-site service is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR
REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk
ozito-diy.co.uk
WARNING! “Read all safety warnings, instructions, illustrations and specications
provided with this power tool.” Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and
ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualied repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of re, electric shock, personal injury and
material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,
before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
Before you connect the equipment to the mains supply make sure that the data on the rating plate are identical
to the mains data.
This tool is double insulated therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid
a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
Using an Extension Lead
Please only use power cables that are not damaged. The total length of the power cable should not exceed
40 meters; going beyond this distance will reduce the power output of the electric motor. The power cable
must have a cross-section of 3 x 1.5 mm2. The insulating sheath of lawn mower power cables is frequently
damaged.
Some of the causes for this are:
• Cuts caused by running over the cable
• Pinching when the power cable is dragging under doors and pulled through windows.
• Cracking due to old age of the insulation
• Kinking by improperly fastening or guiding the power cable.
The power cables must, at the very minimum, be of type HO5RN-F and 3-stranded. The cable type must
be printed somewhere on the power cable. Only purchase power cables that are marked as such! Plugs
and socket couplers for the power cables must be made from rubber and be splashproof. There is a limit to
how long power cables can be. Longer power cables require larger conductor cross-sections. Power cables
and connecting lines must be regularly checked for damage. Ensure that the lines are de-energized before
checking them. Completely unwind the power cable. Also check power cable entry points, plugs and socket
couplers for kinks.
• Read the operating instructions with due care. Familiarize yourself with the operator controls and proper operation of
the machine
• Never allow children or other persons who are not familiar with the operating instructions to use the machine. Contact
your local governmental agency for information regarding minimum age requirements for operating the machine
• Never work in the direct vicinity of persons - especially children - or animals.
• Always keep in mind that the machine operator or user is responsible for accidents involving other persons and/or
damage to their property.
Preliminary measures
• Always wear sturdy, non-slip footwear and long trousers when working. Never operate the machine barefoot or in
sandals.
• Check the ground on which the machine will be used and remove all objects that could be caught up and violently ung
out by it.
• Before using the machine, always visually examine the tools for excessive wear or damage. To prevent any imbalance,
replace worn out or damaged parts and mounting bolts as a set only.
• The power cables used are not to be of a lighter duty class than light rubber-insulated H05RN-F in accordance with DIN
57282/VDE 0282 and they must have a cross section of at least 1.5 mm2. The connection must be splash-proof. The
power cable must be fed through the stress-relief clips and be plugged into the switch/plug block. Before use, check the
cable for damage and signs of aging. Never use the machine with worn or damaged cables. If the cable is damaged
while working, pull the power plug immediately and only then inspect the damage. Do not touch the power cable until the
plug has been pulled. • Socket couplers to connection elements must be made from rubber, soft PVC or other thermal
material of equal rigidity or coated with such material.
• Make sure that all nuts, bolts and screws are tightened securely and that the machine is in safe working condition.
• The equipment may only be connected to a power supply protected by means of an earth-leakage circuit breaker (RCD)
with a maximum operating current of 30 mA.
Handling
• Work only in daylight or in good light.
• Always maintain good footing on inclines.
• Only operate the machine at a walking pace.
• Work perpendicular to the slope, never up or down it.
• Be particularly careful when you change direction on a slope.
• Do not work on overly steep inclines.
• Be particularly careful when you turn the machine around or pull it toward yourself.
• Switch on the motor carefully as described in the instructions from the manufacturer and ensure that you keep your feet
at a safe distance from the tool.
• Never move your hands or feet toward or under any rotating parts.
• Never lift or carry a machine whilst the motor is running; in addition the power plug should be pulled.
• Switch off the motor whenever you leave the machine unattended.
• If the machine begins to experience unusual vibrations, immediately switch it off and check it.
• Ensure that you avoid paths that could restrict the free movement of the extension cable.
• Keep cables away from the cutters. The cutters may cause damage to the cables and result in contact with active parts.
Maintenance and storage.
• Always make sure that all nuts, bolts and screws are tightened securely so that the machine is in safe working condition.
• Allow the motor to cool before you put the machine in an enclosed area.
• For your own safety, replace worn or damaged parts without delay.
• Switch the machine off and pull the power plug before carrying out any adjustment or cleaning work on it, and before
checking to see if the mains connection is entwined or damaged.
• Switch off the motor and pull the power plug:
- before you dislodge any blockages or clogs.
- before you clean the machine, inspect it or carry out work on the machine.
- after you have traveled over an obstacle.
- if you have struck a foreign object.
- if the equipment begins to experience exceptionally strong vibrations
• Do not touch damaged cables before disconnected from the power supply. Touching a damaged cable may result in
contact with active parts.
• Do not touch the cutters before the equipment is disconnected from the power supply and the cutters have reached a
standstill.
Do not lose these safety instructions
Danger!
Sound and vibration
Lpa sound pressure level: 78.4 dB(A)
Kpa uncertainty: 2.5 dB
Lwa
sound power level: 91.93 dB(A)
Kwa uncertainty: 1.5 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions) determined in
accordance with EN 60745.
Vibration emission value ah ≤ 2.5 m/s²
K uncertainty = 1.5 m/s²
The specied vibration value was established in accordance with a
standardized testing method. It may change according to how the electric
equipment is used and may exceed the specied value in exceptional
circumstances.
The specied vibration value can be used to compare the equipment with
other electric power tools.
The specied vibration value can be used for initial assessment of a harmful
effect.
Keep the noise emissions and vibrations to a minimum.
• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in accordance with instructions,
certain residual risks cannot be rules out. The following hazards may
arise in connection with the equipment’s construction and layout:
1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the equipment is used
over a prolonged period or is not properly guided and maintained.
ADDITIONAL INFORMATION
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and
electronic equipment and its implementation in national laws, old electric
power tools have to be separated from other waste and disposed of in an
environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the
owner of the electrical equipment must make sure that the equipment is
properly disposed of if p1-he no longer wants to keep the equipment. The old
equipment can be returned to a suitable collection point that will dispose of
the equipment in accordance with the national recycling and waste disposal
regulations. This does not apply to any accessories or aids without electrical
components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of
documentation and papers accompanying products is permitted only with the
express consent of the iSC GmbH.
Subject to technical changes.
DECLARATION OF CONFORMITY
DESCRIPTION OF SYMBOLS
SERVICE INFORMATION
Danger! Read Note the instructions for use!
Danger! If the cable is damaged or cut, pull out the
power plug from the mains immediately.
Danger! Never use the equipment in damp locations.
Danger! Rotating tool.
Guaranteed sound p er level: 93 dBow
Caution! Wear safety goggles!
Caution! Danger from catapulted parts; keep a safe distance.
Caution! Wear ear muffs!
Danger! Pull the power plug before carrying out maintenance,
cleaning and repair work.
Liu/Product-ManagementWeichselgartner/General-Manager
explains the following conformity according to EU directives and norms for
the following product
Electric Tiller ETL-7530U (Ozito)
2014/29/EU
2005/32/EC_2009/125/EC
2014/35/EU
2006/28/EC
X
2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X
2011/65/EU
X 2006/42/EC
Annex IV
Notied Body:
Notied Body No.:
Reg. No.:
2000/14/EC_2005/88/EC
Annex V
X Annex VI
Noise: measured LWA = 91,93 dB (A); guaranteed LWA = 93 dB (A)
P = 0,75 KW; L/Ø = 30 cm
Notied Body: Société Nationale de Certication et dʼHomologation
S.A.R.L. (SNCH) (0499)
2012/46/EU
Emission No.:
Standard references: EN 60335-1; EN 709; EN 62233;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 11.09.2017
First CE: 17 Archive-File/Record: NAPR017669
Art.-No.: 30.002.09 I.-No.: 11017 R. GehardDocuments registrar:
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
Cord Restraint & Cord
Clips x 2
Please note that the following parts of this product are subject to normal or
natural wear and that the following parts are therefore also required for use as
consumables.
Category Example
Wear parts* Carbon brushes, tines
Consumables
Missing parts
* Not necessarily included in the scope of delivery!
Spare parts can be ordered from the Special Orders Desk at
your local Bunnings Warehouse or Homebase store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: info@ozito-diy.co.uk
SPARE PARTS
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
KNOW YOUR PRODUCT SETUP & PREPARATION
1. BEFORE USE 2. ASSEMBLY 3. STARTING & STOPPING 4. OPERATING THE TILLER
ELECTRIC TILLER
OPERATION
1
2
3
4
5
6
7
8
9 10 11
1. Start/Stop Lever
2. Lock-off Button
3. Upper Handle
4. Lower Handle
5. Motor Housing
6. Lower Handle Bracket
7. Fender
8. Tines
9. Upper Handle Bolt x 2
10. Securing Knob x 2
11. Lower Handle Bolt & Nut x 2
1. Slide the upper handle
over the upper ends of the
lower handle. Fit the bolts
through the upper handle
and then through the hole
in the lower handle.
2. Secure in place by
screwing the supplied
securing knobs over the
protruding ends of the
bolts.
1. First, slide the extension
cord restraint onto the
lower handle.
2. Insert the lower handle
to lower handle brackets
and x in place with the
supplied bolts and nuts.
1. To start the tiller, press and
hold the Lock-off Button.
¥ Water the work area prior to commencing tilling operation.
¥ Move the tiller to the work area prior to starting the motor.
¥ Hold the tiller firmly while switching it on. The tines will pull
the tiller forward during operation.
¥ Hold the upper handle securely, walk backwards slowly and
allow the tines to dig into the work area.
¥ For breaking sod or deep tilling, allow the tines to pull the
tiller forward to the end of your arm’s reach, then firmly pull
the tiller back towards you. By repeatedly allowing the tiller to
move forward and then pulling back to you, the tiller will be
most effective.
¥ For better results, move the machine forward as well as
backwards.
¥ If the tiller digs deep enough to stay in one spot, gently rock
the tiller side to side to start the tiller moving forward again.
¥ Lay the power cable on the ground in front of the outlet in
a gure 8. Work away from the outlet or cable and ensure
that the power cable always trails in the hoed soil which will
prevent the hoe blades from travelling over the cable.
Fitting the Lower Handle
Fitting the Upper Handle
WARNING!: ENSURE ENSURE THE TOOL IS
DISCONNECTED FROM THE POWER SUPPLY BEFORE
ASSEMBLY
2
1
WARNING!: THE POWER SUPPLY FOR THIS PRODUCT
SHOULD BE PROTECTED BY A RESIDUAL CURRENT
DEVICE RATED AT 30mA OR LESS.
Starting the Tiller
For your safety the Tiller is designed with a safety switch. If the
Start/Stop Lever is squeezed, the tiller will not operate. This
prevents accidental start up of the tiller.
2. Pull the Start/Stop Lever
towards the handle, the
motor will start and the Tines
will begin to rotate, then
release the Lock-off Button.
1. Release the Start/Stop Lever to stop the Tiller.
Stopping the Tiller
Tips
For preparing seed bed, we recommend using one of the tilling
patterns.
Tilling Pattern A - Make two
passes over area to be tilled,
the second at a right angle to
the rst.
Tilling Pattern B - Make two
passes over area to be tilled,
the second overlapping the rst.
WARNING!: KEEP
POWER CORD
AWAY FROM TINES.
¥ To prevent tripping take particular care when moving
backwards and when pulling the tiller.
¥ Always let the tines rotates at top speed; do not work in such
a way as to overload the tiller.
¥ Never pass the tiller over the power cord; make sure it is
always in a safe position behind your back.
¥ When working on inclines always stand diagonally to the
incline in a sturdy, safe.
¥ Keep the underside of the machine clean and remove soil
deposits. Deposits make it more difcult to start the machine
and decrease the working depth.
Transport
CAUTION!: BEFORE TRANSPORTING THE TILLER, SWITCH
OF THE MOTOR.
The tines and machine may be damaged even if you move the
tiller with the motor switched off, e.g. over solid ground. Prevent
the tines from touching the ground by carrying out the tiller by
the lower handle.
Cleaning Tines of Foreign Objects
During operation, a stone or root could become lodged in the
tines, or tall grass or weeds may become wrapped around the
tine shaft.
To clear the tines, switch off the tiller. Unplug the tiller, and
dislodge or remove any obstacles from the tines or tine shaft.
To ease removal of tall grass or weeds that are wrapped around
the tine shaft, remove one or more of the tines from the tine
shaft.
Fault Possible Cause Remedy
Motor does not
start
No Power at power
supply
Check the power
supply and fuses
Excessive working
depth.
Reduce working
depth.
Switch & cord set
assembly defective Arrange the repair
by an electrician or
power tool repairer
Abnormal noise Tines are jammed Disconnect power
and determine
cause
Loose bolts and
nuts
Tighten all
components
Abnormal
vibrations
Tines damaged or
worn
Replace tines
Working depth too
large
Adjust for correct
working depth
Poor scarication
results
Working depth too
small
Adjust for correct
working depth
Worn tines Replace tines
Soil too hard Correct working
depth.
ETL-7530U
Items Supplied
Please check that the article is complete as specified in the scope
of delivery. If parts are missing, please contact our service centre or
the sales outlet where you made your purchase at the latest within 5
working days after purchasing the product and upon presentation of
a valid bill of purchase. Also, refer to the warranty table in the service
information at the end of the operating instructions.
¥ Open the packaging and take out the equipment with care.
¥ Remove the packaging material and any packaging and/or
transportation braces (if available).
¥ Check to see if all items are supplied.
¥ Inspect the equipment and accessories for transport damage.
¥ If possible, please keep the packaging until the end of the guarantee
period.
Danger!
The equipment and packaging material are not toys. Do not let
children play with plastic bags, foils or small parts. There is a
danger of swallowing or suffocating!
Proper Use
The machine is designed for digging soil (for example garden beds). Be
sure to observe the restrictions in the safety instructions.
The operating instructions as supplied by the manufacturer must be
kept and referred to in order to ensure that the machine is properly
used and maintained. The instructions contain valuable information on
operating, maintenance and servicing conditions.
For safety reasons, the machine may not be used as a drive unit for
other work tools or tool sets of any kind.
The equipment is to be used only for its prescribed purpose. Any other
use is deemed to be a case of misuse. The user / operator and not
the manufacturer will be liable for any damage or injuries of any kind
caused as a result of this.
Please note that our equipment has not been designed for use in
commercial, trade or industrial applications. Our warranty will be voided
if the machine is used in commercial, trade or industrial businesses or
for equivalent purposes.
5. TROUBLESHOOTING
1. Remove the two screws
and the side cover from the
safety switch.
Fitting the Safety Switch
2. Fit the safety switch to the
upper handle as shown.
3. Ret the side cover and
secure with the screws
removed in step 1.
Securing the Power Cord
1. Secure the power cord from
the switch housing to the
handle using the two cord
clips as shown.
NOTE: Ensure the cord follows
the handle smoothly from the
switch to the body of the tiller.
WARNING!: THE TILLER BLADES WILL CONTINUE TO
ROTATE FOR A FEW SECONDS AFTER THE MOTOR
IS SWITCHED OFF . NEVER ATTEMPT TO MANUALLY
STOP THEM. IN THE EVENT THAT THE ROTATING TILLER
BLADE STRIKES AN OBJECT, IMMEDIATELY SWITCH OFF THE
MACHINE AND WAIT FOR THE TILLER BLADES TO COME TO
A COMPLETE STOP. THEN INSPECT THE CONDITION OF THE
BLADES.
Overload Protection
The tiller has an internal cut off switch which will stop the
operation of the motor temporarily if too high in temperature.
This cut off switch will suddenly stop the motor from operating
should the motor become too hot during the operation of the
tiller.
First disconnect the tiller from the power supply and inspect
blade for any obstructions.
A wait of 10 minutes in cooling time, or longer depending on
ambient temperature and the operation being performed,
before switching On the tiller and resuming normal operation.
CAUTION!: BE PARTICULARLY CAREFUL WHEN YOU PULL
THE MACHINE TOWARD YOURSELF.

Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: ETL-7530U

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito ETL-7530U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Ozito

Ozito

Ozito PXLEK-1840 Handleiding

2 November 2024
Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024
Ozito

Ozito PXNGS-218 Handleiding

8 April 2024
Ozito

Ozito PXHTBK-2518 Handleiding

8 April 2024
Ozito

Ozito PSR-5732U Handleiding

16 Maart 2024
Ozito

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024
Ozito

Ozito PXWBS-200U Handleiding

16 Maart 2024
Ozito

Ozito PXDDK-301U Handleiding

16 Maart 2024
Ozito

Ozito PXCPPS-018U Handleiding

16 Maart 2024
Ozito

Ozito WPHGK-2000U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024