Ozito ASR-150 Handleiding

Ozito Niet gecategoriseerd ASR-150

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito ASR-150 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 247 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
DESCRIPTION OF SYMBOLS SPARE PARTS
AIR RANDOM
ORBITAL SANDER
150mm (6”)
INSTRUCTION MANUAL
SPECIFICATIONS
ASR-150
Sanding Pad Size: 150mm (6”)
Max. Air Pressure: 91psi (6.3Bar)
Average Air Consumption: 113 l/min (4cfm)
No Load Speed: 10,000/min
Air Inlet: 1/4” BSP
Weight: 1.73kg
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
Email: enquiries@ozito.com.au
GENERAL AIR TOOL SAFETY WARNINGS
AIR SANDER SAFETY WARNINGS
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings
refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Cluttered or dark areas invite accidents. Keep work area clean and well lit.
b. Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
c. Distractions can Keep children and bystanders away while operating a power tool.
cause you to lose control.
d. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
e. Check the maximum pressure rating of any tools or accessories that you intend using with
the compressor. The output pressure of the air from the compressor must be regulated so
that it never exceeds the rated pressure of the tool or accessory.
f. Always wear safety goggles or glasses when using the air compressor. Never point the
nozzle of an accessory towards any part of your body or towards another person.
g. Drain the moisture from the tank daily. It will help prevent corrosion.
h. Use safety equipment including safety goggles or shield, ear protection, breathing respirator
mask and protective clothing.
i. Air tools should not be used in a potentially explosive environment.
j. Use safety equipment including safety goggles or shield, ear protection, breathing or
respirator mask and protective clothing.
k. The tool must be used only for its prescribed purpose. Any use other than those mentioned
in this Manual will be considered a case of misuse. The user and not the manufacturer
shall be liable for any damage or injury resulting from such cases of misuse.
WARNING! In the event that an air line is cut or broken, the air supply must be turned off
at the compressor. A broken air line which is not supported is extremely dangerous and
can whip around very quickly, both with the capability of striking people, and blowing foreign
particles into the air.
Do not attempt to catch the air line but immediately keep bystanders well clear and turn off the air
supply to the hose, turn off the compressor at the On / Off button, and then remove the hose from
the compressor.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given the supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Warning Read instruction
manual
Wear eye protection
No load speed
Wear ear protection
Revolutions or
reciprocation per minute
/min no
• Larger sandpaper will extend Do not use sandpaper intended for larger sanding pads.
beyond the sanding pad causing snagging, tearing of the paper or kick-back.
Extra paper extending beyond the sanding pad can also cause serious lacerations.
WARNING!
Some dust created by power sanding, sawing, grinding, drilling and other construction
activities contain chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints;
• Crystalline silica from bricks, cement and other masonry products, and;
• Arsenic and chromium from chemically-treated timber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area and work with approved
safety equipment, such as dust masks that are specially designed to filter out microscopic
particles.
1 Sanding Pad
2 Spindle
3 Air Regulator
4 On/Off Trigger
5 Handle
6 Air Inlet (1/4” Nitto Fitting)
KNOW YOUR PRODUCT
WARNING!
• Accidental start-ups may Disconnect the sander before changing accessories.
occur if the sander is plugged in while changing an accessory.
• Be extremely careful of dust disposal, materials in fine particle form Disposing of dust.
may be explosive. Do not throw sanding dust on an open fire. Spontaneous combustion, may
in time, result from a mixture of oil or water with dust particles.
• Always wear eye protection and a dust mask for dusty applications and when
sanding overhead. Sanding particles can be absorbed by your eyes and inhaled easily and
may cause health complications.
• Use special precautions when sanding chemically pressure treated timber, paint that
may be lead based, or any other materials that may contain carcinogens. A suitable
breathing respirator and protective clothing must be worn by all persons entering the work
area. Work should be sealed by plastic sheeting and persons not protected should be kept out
until work area is thoroughly cleaned.
• Do not ‘wet sand’ with this sander.
• Accessory may kickback over your Never place your hands near rotating components.
hand.
TROUBLESHOOTINGMAINTENANCE
If the sander fails to work effecvely, perform the following
checks:
• Check that the air regulator dial is not completely closed.
• Check the air inlet is free of any dirt or blockages.
• Ensure the sander is lubricated properly.
• Check that the pressure on the air compressor is within its
||working range. If not, let the compressor rest to
||re-pressurise / refer to the compressor instruction manual.
Note: This tool is rated at 90psi. Ensure your compressor is set no higher than 90psi.
• If the enclosure of the sander requires cleaning, do not use
solvents but a moist soft cloth only. Never let any liquid get inside
the sander; never immerse any part of the sander into a liquid.
• Store the tool in a dry and safe place out of reach of children.
• Oil the air sander after each use.
CONNECTING TO COMPRESSOR
OPERATION
FITTING SAND PAPER
3. Screw the male nio fing
clockwise into the female end
of the air inlet.
4. Pull back the sleeve on hose
fing, insert male end & release
sleeve on hose fing.
1. Remove black plasc cap
from the air inlet.
2. Wrap the threaded male
end of an air fing with
thread sealing tape in a
clockwise direcon.
2. Press the on/off trigger down to
start sanding.
To stop the sander, release the
on/off trigger.
1. Ensure that the workpiece is secured
with clamps to avoid movement while
sanding.
2. Press the sand paper onto the
sanding pad, making sure to align
the edges.
1. Screw the sanding pad ghtly
onto the spindle by rotang
clockwise. Use a spanner to hold
the spindle while ghtening.
3. To adjust the rotaonal speed of
the sander, rotate the air regulator
dial unl the desired seng is
achieved.
Note: Disconnect the tool from the air supply before fing or removing aachments.
3. To remove the sand paper, peel
off starng from one edge.

Product specificaties

Merk: Ozito
Categorie: Niet gecategoriseerd
Model: ASR-150

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito ASR-150 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Ozito

Ozito

Ozito PXLEK-1840 Handleiding

2 November 2024
Ozito

Ozito PXPPS-1820 Handleiding

8 April 2024
Ozito

Ozito PXNGS-218 Handleiding

8 April 2024
Ozito

Ozito PXHTBK-2518 Handleiding

8 April 2024
Ozito

Ozito PSR-5732U Handleiding

16 Maart 2024
Ozito

Ozito PXCLMLTC-418U Handleiding

16 Maart 2024
Ozito

Ozito PXWBS-200U Handleiding

16 Maart 2024
Ozito

Ozito PXDDK-301U Handleiding

16 Maart 2024
Ozito

Ozito PXCPPS-018U Handleiding

16 Maart 2024
Ozito

Ozito WPHGK-2000U Handleiding

16 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024