Nissin Di622 Mark II Handleiding

Nissin Flitser Di622 Mark II

Lees hieronder de 📖 handleiding in het Nederlandse voor Nissin Di622 Mark II (6 pagina's) in de categorie Flitser. Deze handleiding was nuttig voor 84 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

for Canon EOS / Nikon digital SLR cameras

for Sony digital SLR cameras

INSTRUCTION MANUAL

Nissin Japan Ltd., Tokyo

http://www.nissin-japan.com

Nissin Marketing Ltd., Hong Kong

http://www.nissindigital.com

Nissin Di622 Mark II is designed for digital SLR cameras with hotshoe

and the latest TTL flash control technology.

Note: No film camera can be used with Di622 Mark II.

Attach Di622 Mark II to your camera, and then almost all jobs are

controlled by the camera for the most proper exposure.

Read this instruction manual and refer your canera owner’s manual to

enjoy flash photography.

The compatibility list of Di622 Mark II, please check at our official

website: www.nissindigital.com

WARNING

The flash unit contains high voltage electric parts. Do not try

to open or repair the flash unit. Return it back to the repair

service station or the store you bought it.

Do not touch the inside parts from the opening when the unit

was dropped and broken.

Do not fire the flash direct to the eye at short distance. It may

damage the eye. When taking flash picture especially

toward a baby, it is recommended to keep the flash unit at

least 1 meter (3.3feet) away from the subject.

Or use diffuser or bounce the light to the ceiling or to the wall

to soften its intensity.

Do not use the flash unit in the flammable gas, chemicals or

such liquids. It may cause fire or electric shock.

CAUTIONS

Do not leave or store the flash unit in the temperature over

40°C, such like in the automobile.

The flash unit is not water resistant. Keep the unit away from

rain, snow and humidity.

Do not use benzene, thinner or other alcoholic agents to

clean the unit.

Do not use this flash with the cameras which is not listed in

the compatibility list at our official website, otherwise it may

damage the camera’s circuitry.

Remove the batteries when not in use for a longer period of

time.

This sign refers the danger or serious damage.

This sign refers the damage or defect.

622II.Rev.0211.1.0

Design and Specifications are subject to change without prior notice.

Ch 1 G roup A

Names of the Components

Flash stand

Light diffusing panel / Fill-in reflector

Flash head

AF-assist light / wireless flash sensor

Lock ring

Mounting foot

Hotshoe contacts

X - Terminal

Pilot lamp (Test flash button)

Battery compartment door

Power switch (Press button)

Mode select button / indicator

(TTL Manual SD SF Wireless) → → → →

Flash power leveel indication lamp (6 LEDs)

Flash power level select button

Accessories: Flash stand, Pouch

Basic Operation

Inserting batteries

Open the battery compartment door and

insert 4 x size AA batteries as shown by

the picture.

Make sure the + and - battery contacts are

correctly inserted at the battery compart-

ment.

Close the battery compartment door and

slide it back in place.

NOTE

Wrong insertion or using different size batteries may result damage on the

flash unit.

It is recommended to use all 4 batteries in same brand and type, and

replace them all att p2-he same time.

Ch 1 Group A

ilo

On/O ﬀ

Ch 1 Grou p A

On/Oﬀ

Ch 1 Group A

ilo

On/O ﬀ

Mounting Di622 Mark II on the camera

Slide the mounting foot of Di622 Mark

II into the hotshoe of camera.

Twist the lock ring clockwise to tighten

it.

Twist the lock ring anti-clockwise to

loosen it as shown in the picture.

Removing Di622 Mark II from the camera

Loosen the lock ring and slide the mounting foot of Di622 Mark II off

the hotshoe of camera.

Before mounting or removing Di622 Mark II into or from the camera,

make sure to turn off the power switch of both Di622 Mark II and the

camera.

NOTE

Push the lever of the locking ring (in the

direction of the arrow) of Di622 Mark II

to loosen it as shown in the picture.

Slide the mounting foot of Di622 Mark

II into the hotshoe of the camera while

holding down the lock ring .

Release the lock ring of Di622 Mark II

when the mounting foot is fully slide into

the hotshoe of the camera.

Lock pin comes out to hook the foot at

the hotshoe for sure contact.

*For Nikon and Canon type digital SLR cameras

Mounting Di622 Mark II on the camera

*For Sony type digital SLR cameras

*Sony type hotshoe / Flash stand

Removing Di622 Mark II from the camera

Push down the lock ring and slide the mounting foot of Di866 Mark II

off the hotshoe of the camera. Make sure to slide off the mounting foot

and completely clear the lock pin off the hooking slot on the hotshoe.

Before mounting or removing Di622 Mark II into or from the camera,

make sure to turn off the power switch of both Di622 Mark II and the

camera.

NOTE

Turn on the flash unit

D F

Ch1 Group A

For a test flash, press the Pilot lamp. When using

the test flash as an open flash, please note that the

reference guide number in this case is G.No.10 (ISO

100).

To turn off the flash unit manually, press the On/Off

switch for 2 seconds.

Press the On/Off switch and Pilot

lamp turns red showing the unit is

turned on.

In a few seconds, the Pilot lamp

turns green. Di622 Mark II is

ready to shoot.

Di622 Mark II has energy saving double power off function

To save battery energy, the power is automatically turned off

(switch to stand-by mode), both in TTL mode & Manual Power

mode, in about 2 minutes of idle use.

While Di622 Mark II is in the stand-by mode a Pilot lamp blinks

every 2 seconds showing the flash unit is in stand-by mode.

To turn on Di622 Mark II again, press the camera’s shutter button

halfway or press any button of the flash unit.

In case Di622 Mark II is not in use over 30 minutes, the unit is

completely turned off and shut out the current leakage from the

batteries.

To turn on Di622 Mark II again, take the first step of turning the

flash unit on.

In case of using Di622 Mark II in slave or remote mode, Di622

Mark II will not go into the stand-by mode. It will however

automatically turn off when not used over 60 minutes.

Shooting Di622 Mark II automatically

Canon cameras

Nikon cameras

(Program), (Full Auto), (Aperture priority),

(Shutter priority) or (Manual); and / or

(Program), (Full Auto), (Aperture priority),

(Shutter priority) or (Manual);

Set the camera’s shooting mode, select focal length and take pictures with

Di622 Mark II on your camera.

Di622 Mark II is a supplement to help you taking a creative and live

picture. Almost all jobs are automatically done by the camera and you just

control the camera only.

Set Di622 Mark II to the camera’s hotshoe and turn on the power switch.

Di622 Mark II is automatically set for the camera’s TTL mode when

ready lamp lights up.

Press the shutter button of your camera halfway to focus the subject.

Take the picture. Di622 Mark II is fired and the result is immediately shown

on the camera’s LCD display.

When you change the focal length, The power zoom flash head of

Di622 Mark II responds without delay and immediately sets its position to

match the lens focal length you selected.

The flash illumination coverage of Di622 Mark II responds to the lens

focal length of 24mm to 105mm (35mm film camera standard).

In all camera's shooting mode listed above, Di622 Mark II will fully work

in TTL (ETTL, ETTL-II for Canon, i-TTL for Nikon and ADI, P-TTL for Sony )

automatic-flash system.

Shutter speed, aperture and flash mark ( ) are indicated in camera’s view

finder.

Mode

Canon Nikon Sony

Shutter

Speed

Aperture

Setting

Control on

the camera

Automatic Automatic Automatic

Manual Automatic

Automatic Manual

Manual Manual

Any available shutter

speed can be set

Any available f-stop

can be set

Any available shutter

speed / f-stop can be set

Synchro Terminal

Di622 Mark II equipped a Synchro terminal (X terminal) to connect the

off-camera cable, allows photography with flash units seperate from

the camera. This feature can be applied in Manual mode only.

Joy of Flash Photography

TTL flash power compensation is provided in 7 steps by half Ev

increment for -1.5, -1.0, -0.5, 0, +0.5, +1.0, and +1.5 Ev.

Set the Flash power level select button to the power level you desire.

When Di622 Mark II shows no level indication LED is turned on, the

flash power compensation level is at even (0 Ev) level as default

value.

Take a picture and the aimed subject is shown with required lighting

effect by keeping the background exposure level as originally

expected.

Press the flash power select button, by each press of + marked knob,

it sets the power of +0.5 +1.0 +1.5 Ev. and the - marked knob → →

sets it to -0.5 -1.0 -1.5 Ev. The power level indication lamp → →

shows the power level you set.

On some cameras, the TTL flash power compensation setting is

provided in its menu mode.

When setting the TTL flash power compensation on your camera, the

same of Di622 Mark II is, in this case, to be counted in addition to

the compensation you selected in the camera’s menu mode.

With the latest TTL flash control system, the

flash power level is always automatically

controlled by the camera for the most

appropriate exposure. You wish if you can

soften or weaken the flash light, or give more

light to the subject without changing the

environmental or background exposure effect

Di622 Mark II can make it possible quickly

for each shot at respective occasion of flash

picture.

TTL flash power compensation

Ch1 Group A

Sony cameras

(Program), (Full Auto), (Aperture priority),

(Shutter priority) or (Manual);

Product specificaties

Merk:	Nissin
Categorie:	Flitser
Model:	Di622 Mark II
Kleur van het product:	Zwart
Gewicht:	315 g
Brandpuntbereik:	24 - 105 mm
Ondersteund aantal accu's/batterijen:	4
Flitser-modi:	Manual, Slave
Opbergetui:	Ja
Kleurtemperatuur:	5600 K
Draadloze verbindingen:	Ja
Auto Focus (AF) assisteer straal:	Ja
Aantal kanalen:	1 kanalen
Afmetingen (B x D x H):	74 x 103 x 134 mm
Type batterij:	AA
Bereik:	0.7 - 6 m
Compatibele camera merken:	Sony
Oplaadtijd (ongeveer):	5 s
Richtgetal (35mm zoomstand, ISO 100):	44 m
Merk specifieke flits systemen:	ADI/P-TTL (Sony)
Richtgetal flitser:	62 m
Group settings:	1
kantel aanpassingen:	Ja
Aantal flitsen (ongeveer):	200 - 1500