MSR AUTOFLOW Handleiding

MSR Waterfilter AUTOFLOW

Lees hieronder de 📖 handleiding in het Nederlandse voor MSR AUTOFLOW (2 pagina's) in de categorie Waterfilter. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Problem

Poor Performance Cause Solution

Leaking Female Quick

Disconnect

Clogged Female Quick

Disconnect

Rinse Female Quick

Disconnect

Decreased/no water flow Trapped air in Filter Cartridge Filter 1/4 L water into clean con-

tainer and then lift it above Dirty

Collection Reservoir to purge air

(see )Tips

Clogged Pre-Filter Screen Clean Pre-Filter Screen

Clogged filter Backflush Filter Cartridge

(see )Step 4

Kinked hose Straighten hose

Disengaged Male Quick

Disconnect

Push Male Quick Disconnect into

fitting completely

Closed Shut-off Clamp Open Shut-off Clamp

Kit Contents Dirty Collection Reservoir (with built-in Female Quick

Disconnect fitting)

Male Quick Disconnect fitting

Filter Cartridge

Inlet Hose (12 in./30 cm)

Outlet Hose (48 in./122 cm)

Universal Bottle Adapter

Clean Side Cover

Shut-off Clamp

Instruction Manual

Filter Test Guide

Storage Sack

Weight 14.2 oz. / 402 g

Dimensions 10 x 3.5 in. / 25 x 9 cm

Flow Rate ~ 1.75 liters per min. (depends on filter condition,

water quality)

Filter Life ~ 1500 liters (depends on water conditions)

Filter Media Hollow Fiber Membrane (HFM)*

Storage Temperature Above 32 F / 0 C (Do Not Freeze)

Patents Patents pending

*The Hollow Fiber Membrane (HFM) is a collection of small, porous tubes that

can be damaged by dropping or freezing. This damage cannot be seen. Follow

Filter Test Guide to inspect ﬁlter and detect possible damage.

ENG

INSTRUCTION

MANUAL

AUTOFLOW™ GRAVITY FILTER

For product information and ser vice contact

C a s c a d e D e sig ns, I nc.

4 00 0 F ir st Av e n ue S o u t h , S e a t t l e, WA 981 34 US A

1-800-531-9531 or 206-505-9500

w ww. m s rge a r. co m

in f o@ c a s ca d e d e s ig n s . c o m

LIMITED WARRANTY/LIMITATIONS OF REMEDIES AND LIABILITY

USA and Canada

Limited Warranty. Cascade Designs, Inc. (“Cascade”), to the original owner (“Owner”), under intended

use and maintenance, warrants the enclosed product (“Product”) to be free from defects in materials

and workmanship for the life of the Product. No warranty against defects in materials and workmanship will apply if

Product is (i) altered in any way, (ii) used for purposes inconsistent with Product’s intended purpose or design, or (iii) improperly

maintained. Warranty will furthermore be voided where Owner/user (i) failed to follow Product instructions or warnings or (ii)

subjected Product to misuse, abuse, or neglect.

During the warranty period, original Product parts determined by Cascade to be defective in materials or workmanship will

be repaired or replaced as Owner’s sole remedy. Cascade reserves the right to replace any discontinued product with a new

product of comparable value and function. A returned product deemed irreparable becomes the property of Cascade and

will not be returned.

EXCLUDING THE LIMITED WARRANTY PROVIDED ABOVE, CASCADE, ITS AFFILIATES AND THEIR SUPPLIERS, TO THE

MAXIMUM EXTENT PERMITTED BY LAW, MAKE NO WARRANTIES, EXPRESSED OR IMPLIED, AND DISCLAIM ALL

WARRANTIES, DUTIES AND CONDITIONS, WHETHER EXPRESSED, IMPLIED OR STATUTORY, WITH RESPECT TO THE

PRODUCT, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, AGAINST LATENT

DEFECTS, FITNESS FOR A PARTICULAR PURPOSE, OR CORRESPONDENCE TO DESCRIPTION.

Warranty Service. To obtain service under this warranty, the warranty-eligible Product must be presented to a Cascade

authorized dealer. In the United States and Canada, warranty service may also be obtained by calling 1.800.531.953

[M - F, 8:00 a.m. - 4:30 p.m., PDT]. Owner is responsible for all costs associated with returning Product to Cascade for service.

Where at its sole discretion Cascade deems Product eligible for warranty repair or replacement, Cascade will pay the shipping

and handling associated with returning repaired or replaced Product to Owner. In instances where Cascade deems a returned

product ineligible for warranty service, Cascade will, if possible, repair product for a reasonable charge that includes return

shipping and handling. For warranty return service details, please go to www.msrgear.com.

Limitation of Remedies. Should a court of competent jurisdiction find the limited warranty set forth above breached, Cascade’s

only obligation will be to, at its option, either repair or replace Product. Should the aforementioned remedy fail of its essential

purpose, Cascade will, in exchange for return of Product, refund to Owner Product’s original purchase price. THE FOREGOING

REMEDY IS THE SOLE AND EXCLUSIVE REMEDY OF THE PURCHASER AGAINST CASCADE, ITS AFFILIATES AND THEIR

SUPPLIERS, REGARDLESS OF LEGAL THEORY.

Limitation of Liability. Cascade’s, its affiliates’ and their suppliers’ maximum liability is limited to incidental damages not to

exceed the original purchase price of the Product. CASCADE, ITS AFFILIATES AND THEIR SUPPLIERS HEREBY DISCLAIM

AND EXCLUDE ANY LIABILITY FOR ANY CONSEQUENTIAL OR OTHER DAMAGES RESULTING FROM ANY REASON

WHATSOEVER. THIS EXCLUSION AND LIMITATION APPLIES TO ALL LEGAL THEORIES UNDER WHICH DAMAGES MAY BE

SOUGHT, AND WILL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE.

This limited warranty gives Owner specific legal rights; Owner may have additional rights, which may vary state to state.

Always completely follow safety, use, operation, and maintenance instructions for this or any other Cascade product.

European Union customer statutory rights are not affected.

Cascade Designs, Ltd.

Dwyer Road, Midleton, County Cork, Ireland

(+353) 21-4621400

WARNING

Printed on 5 0% Recycled (30% PCR) Paper. Processed Chlorine/Acid Free. 15 981 1- 2

TROUBLESHOOTING

SPECIFICATIONS

TIPS

IMPORTANT

Read and understand this entire manual carefully before assembling or using this

water filter. Keep this manual for future reference. If you do not understand this

manual or have any questions, please call Cascade Designs at 1-800-531-9531.

www.msrgear.com

For product service and information contact

BIOLOGICAL HAZARD

There are hazards associated with backcountry travel and the use of water fil-

ters. Drinking untreated water may expose you to harmful microorganisms and

increase your risk of gastrointestinal illness. Using this filter improperly increases

your risk of exposure to harmful microorganisms and increases your risk of

gastrointestinal illness. Reduce your chances of becoming sick by following the

warnings and instructions in this manual and educating yourself on backcountry

water safety.

YOU ARE RESPONSIBLE FOR YOUR OWN SAFETY AND THE SAFETY OF

THOSE IN YOUR GROUP. PLEASE USE GOOD JUDGMENT.

Never use the AutoFlow to filter seawater or chemically contaminated water,

such as water from mining tailing ponds or near large agricultural operations.

The AutoFlow does not make drinkable water from these sources and does not

remove all viruses, chemicals and radioactive materials, or particles smaller

than 0.2 microns.

Keep the hoses and other potentially contaminated parts away from filtered

water to prevent cross contamination.

READ, UNDERSTAND, AND FOLLOW ALL instructions and warnings in this

manual before using this filter. Failure to follow warnings and instructions may

result in gastrointestinal illness.

Filter Cartridge

Clean the cartridge by backflushing it every 8 liters (1x/day of use) to prevent silt build-up

and extend the filter’s lifespan. (See instruction manual.) If backflushing fails to Step 4,

restore water flow, replace cartridge.

On extended trips, bring along a spare cartridge, which can be purchased from a local or

online MSR dealer.

Water Collection and Preparation

Use the cleanest, clearest water available.

Avoid filtering silty, cloudy, muddy, or glacial stream water or tea-colored water that con-

tains visible tannins because these sources will quickly clog the filter.

If clear water is not available, then let particles settle before filtering. Fill the Dirty Collection

Reservoir with water and let the water stand until particles have settled to the bottom. Clear

the Pre-Filter Screen behind the Female Quick Disconnect as needed.

To treat water with suspected waterborne viruses, use an approved disinfectant. Follow the

manufacturer’s recommendation for its use. Information on disinfectant use can be found on

the Centers for Disease Control Web site: www.CDC.gov.

Operation

To maximize water flow, hang the Dirty Collection Reservoir as high as possible

without putting tension on the hoses or pulling the clean container off the ground.

Trapped air in the top of the Filter Cartridge may reduce water flow. Purge the trapped

air by first filtering some water (1/4 L) into the clean container and then lifting it (without

kinking the hoses) above the Dirty Collection Reservoir to reverse the water flow. Once the

air bubbles are purged, place the clean container on the ground and allow the system to

resume filtering water.

Alternate Collection Methods

To avoid cross contamination when filtering water,

MSR recommends these collection methods:

MSR® Universal Bottle Adapter –

Threaded (MSR® Dromedary™ Bag,

Nalgene® bottles, and other similar

products)

Remove Clean Side Cover. Thread Universal Bottle

Adapter onto the bag or bottle spout. Follow

Steps 1-3 (instruction manual). After the water is

filtered and collected, replace bag or bottle cap.

Reattach Clean Side Cover and store.

MSR® Universal Bottle Adapter –

Pressed (Platypus® Hoser™, Sigg®

bottles,

and other similar products)

Remove Clean Side Cover. Press Universal Bottle

Adapter onto bottle spout. Follow Steps 1-3

(instruction manual). After water is filtered and

collected, replace bottle cap. Reattach Clean Side

Cover and store.

MSR® Universal Bottle Adapter –

Drink Tube (Platypus®, CamelBak®

hands-free hydration systems)

Remove the Bite Valve and store in a clean place.

Attach Hydration Drink Tube to Universal Bottle

Adapter. Follow (instruction manual). Steps 1-3

After the water is filtered and collected, reinstall

Bite Valve. Reattach Clean Side Cover and store.

Cascade Designs, Inc.

4000 First Avenue South, Seattle, WA 98134 USA

1-800-531-9531 or 206-505-9500

UNIVERSAL

BOTTLE ADAPTER

(PRESSED)

DRINK TUBE

UNIVERSAL

BOTTLE ADAPTER

(THREADED)

FILTER WATER PACK AND STORE AUTOFLOW SYSTEM

MSR® AUTOFLOW™ GRAVITY FILTER

OPERATING INSTRUCTIONS

PREPARE AUTOFLOW SYSTEM

KNOW YOUR MSR® AUTOFLOW™ GRAVITY FILTER

Never store Filter Cartridge in cold temperatures (below 32 F/0 C)

because freezing the filter will permanently damage the internal fibers.

Always wash and dry filter parts.

DISINFECT FILTER

1. Connect open end of Inlet Hose to black Inlet Hose Barb.

NOTE: Arrow (water flow direction) on Filter Cartridge should point toward

clean container.

2. Connect Outlet Hose to white Outlet Hose Barb.

3. Connect open end of Outlet Hose to Universal Bottle Adapter.

4. Remove Clean Side Cover and attach a clean container to the Universal

Bottle Adapter.

(See )Tips.

5. Close Shut-off Clamp on Outlet Hose.

1. Remove Male Quick Disconnect from the

Female Quick Disconnect on the Dirty

Collection Reservoir.

2. Fill the Dirty Collection Reservoir with

unfiltered water.

3. Fold the Closure Strap on the Dirty

Collection Reservoir 4+ times to seal.

Connect the buckles of the Closure

Strap to each other.

4. Suspend the Dirty Collection Reservoir by

the Hang Strap.

NOTE: Hang the Dirty Collection Reservoir

as high as possible without putting tension

on the hoses or pulling the clean container

off the ground.

5. Reinstall the Male Quick Disconnect.

6. Open Shut-off Clamp to start water flow.

Allow water to flow down from Dirty

Collection Reservoir through Filter

Cartridge into clean container.

NOTE: Trapped air in Filter Cartridge will

affect water flow. Purge air by filtering

some water (1/4 L) into the clean con-

tainer and then lifting it above the Dirty

Collection Reservoir.

1. Empty all water from system.

2. Reattach Clean Side Cover to Universal Bottle Adapter.

3. Wind hoses around Filter Cartridge.

NOTE: All parts (reservoir, hoses, cartridge, adapter) should remain

connected to avoid cross contamination during field storage.

4. Roll Dirty Collection Reservoir around Filter Cartridge and hoses and place

in the storage sack.

Always disinfect the filter before or after long-term storage, or after long-

term use (15+ consecutive days). See Step 5.

CONNECT INLET HOSE

TO INLET HOSE BARB

HANG

RESERVOIR

WARNING

When filtering water, never splash dirty or unfiltered water into clean

container to avoid contamination.

To eliminate the growth of bacteria or mold, always disinfect the filter before

or after long-term storage, or after long-term use (15+ consecutive days).

1. Remove Male Disconnect from Dirty Collection Reservoir.

2. Rinse Dirty Collection Reservoir with clean water.

Remove any debris from the Pre-Filter Screen.

3. Mix a solution of 2 drops of household bleach to 1 liter of water in Dirty

Collection Reservoir.

4. Assemble AutoFlow system.

Close Shut-off Clamp to stop water flow.

Place open end of Outlet Hose (or Universal Bottle Adapter) in sink.

Hold or hang Dirty Collection Reservoir above sink.

5. Open Shut-off Clamp and let bleach solution filter through system into sink.

6. Air or towel dry AutoFlow system parts completely.

NOTE: The inside of the Filter Cartridge will not dry completely, but the

bleach in the solution will prevent the growth of harmful microorganisms

and biofilm.

7. Pack and store AutoFlow assembly in storage sack.

Hang

Strap

Hang Buckle

Closure

Strap

Closure

Buckle

Male Quick

Disconnect

Female Quick

Disconnect

Pre-Filter

Screen

Dirty

Collection

Reservoir

CONNECT OUTLET HOSE TO

UNIVERSAL BOTTLE ADAPTER

ATTACH

CLEAN SIDE

COVER

WARNING

Handle Filter Cartridge carefully because a damaged filter cannot

prevent exposure to harmful microorganisms. Test filter for damage if

dropped 5 feet (1.5 meters) or greater onto a hard surface. (See Filter

Test Guide.) If filter is damaged, discontinue use and replace cartridge.

WARNING

Disinfect the filter thoroughly before long-term storage to prevent the

growth of mold, mildew, and bacteria. Never use a dishwasher or micro-

wave to disinfect parts because the high heat will damage or melt them.

BACKFLUSH FILTER CARTRIDGE

Regularly backflush Filter Cartridge

every 8 liters (more frequently for

cloudy or tea-colored water) to clean

it, maintain optimal water flow, and

extend the filter’s lifespan.

1. Collect at least ½ liter of filtered

water in clean MSR recommended

container. (See )Tips.

2. Remove the Inlet Hose from the barb

of the Male Quick Disconnect.

3. Hold or hang clean container above

the Filter Cartridge and allow water

to flow back through the filter and

out of Male Quick Disconnect.

4. Allow at least ½ liter to flow through

Filter Cartridge to remove debris

collected in the fibers.

For long-term storage of the

AutoFlow system, see Step 5.

Inlet Hose

Barb

Outlet Hose

(48 in./122 cm)

Shut-off

Clamp

Filter

Cartridge

Outlet Hose

Barb

Inlet Hose

(12 in./30 cm)

Universal

Bottle

Adapter

Clean Side

Cover

FOLD CLOSURE

STRAP

CLOSE SHUT-OFF

CLAMP

BACKFLUSH FILTER

CARTRIDGE

DIRTY COLLECTION

RESERVOIR

CLEAN

COLLEC TION

RESERVOIR

WARNING

OPEN SHUT-OFF

CLAMP

Product specificaties

Merk:	MSR
Categorie:	Waterfilter
Model:	AUTOFLOW
Kleur van het product:	Rood
Gewicht:	299 g
Aantal per verpakking:	1 stuk(s)
Waterstroom 9min):	1.75 l/min

Heb je hulp nodig?

Als je hulp nodig hebt met MSR AUTOFLOW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Waterfilter MSR

MSR Guardian Purifier Handleiding

21 Juni 2023

MSR AUTOFLOW Handleiding

1 Juni 2023

Handleiding Waterfilter

Nieuwste handleidingen voor Waterfilter

Eden 521 Handleiding

15 November 2024

LARQ Bottle Movement Handleiding

14 November 2024

JBL Pro Cristal Compact Plus UV-C Handleiding

28 Oktober 2024

Laica J51-BC Handleiding

15 Oktober 2024

Laica J11-AB Handleiding

15 Oktober 2024

Laica J35-EB Handleiding

15 Oktober 2024

Laica J35-AD Handleiding

15 Oktober 2024

Fluval AquaClear AC30 Handleiding

24 September 2024

Fluval AquaClear AC50 Handleiding

24 September 2024

Fluval AquaClear AC20 Handleiding

24 September 2024