MOZA Hand Brake Handleiding

MOZA Controller Hand Brake

Lees hieronder de 📖 handleiding in het Nederlandse voor MOZA Hand Brake (1 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

MOZA 手刹使用说明书

尺寸：260*160mm(对折后130*160mm)

材质：80g书写纸

双面印刷

对折线

• 材质：铝合金

• 尺寸： 153 * 68.3 * 365.5mm

• 可调阻力：支持

• 横置手柄安装：支持

• 侧装支架：选配

• 安装孔： M6

• 净重： 0.7Kg

产品介绍

手刹握柄的高度与角度调节

包装清单

产品参数

• 手刹座

• 握杆

• 1* 十字螺丝刀

• 1* 一字螺丝刀

• 1* 弹簧（蓝）

• 2* 开口扳手

• 2* 数据线（ Type-B，RJ45）

• 2* 外六角螺丝（带平垫，弹帽）

• 2* 内六角伞头螺丝（带平垫）

• 3* 六角扳手

• 1*阻尼块

• 2*阻尼块垫片

弹簧和阻尼块的更换

1. 使用十字螺丝刀取下弹簧上部的盖板；

2. 使用六角扳手取下两侧安装弹簧挡块的螺丝；

3. 沿外侧拉动手刹握杆使弹簧与挡板翘起；

4. 使用一字螺丝刀将螺丝取下并更换合适强度的弹簧；

5. 将挡板调整到合适位置后锁紧螺丝，最后将盖板弻位并锁紧全部螺丝。

在MOZA Pit house中的设置

PASS

Quick Guide

• 航空级铝合金 • 16位高精角度传感器

• 双模式多角度任意切换 • 力度行程可调

• 手柄高度可调 • 多接口设计

• 便捷安装

1. 使用两个开口扳手固定住六角螺丝与螺帽两侧；

2. 逆时针拧松螺帽，调整好适合的握杆高度与角度后安装回螺丝并拧紧

（请注意安装与螺丝搭配的平垫与弹垫，避免刮花握杆外侧）。

1. 如图，可在Pit house中设置手刹的起始点和终点以改变其行程或消除死区

2. 可通过曲线调节界面调节手刹前段和后段的机械行程与信号输出的关系

3. 若手刹输出异常，可点击标定按钮，按照提示重新标定

4. 可选择按键模式或轴模式，将手刹切换为仅具备开关的按键或有连续行程

的轴

MOZA Hand Brake User manual

• Material: Aluminum

• Dimension: 153* 68.3* • 365.5mm

• Adjustable resistance: supported

• Horizontal lever mount: supported

• Side-mount: optional

• Bolt pattern: M6

• Net weight: 0.7 KG

Product Introduction

Lever Height & Angle Adjustment

Package Content

Product Parameters

• Handbrake base

• Handbrake lever

• 1 * Philips screwdriver

• 1 * Flathead screwdriver

• 1 * Spring (blue color)

• 2 * Hex screws

• 2 * data cables (USB-b, RJ45)

• 2 * hex screws (come with ﬂat pads,

spring pads, and nuts)

• 2 * umbrella head screws (come with ﬂat pads)

• 3* Allen wrenches

• 1*Damper

• 2*Damper spacers

Spring Replacement

1. Remove the cover above the spring with a Phillips screwdriver

2. Remove the bafﬂes on both sides with an Allen wrench

3. Pull the handbrake lever until the spring and the bafﬂes tilt

4. Remove the screws with a ﬂat-head screwdriver and install the spring

5. Adjust the bafﬂe, put the cover back in place, and tighten all screws

Conﬁguration in MOZA Pit House

Quick Guide

• Aviation-grade Aluminum • Easy to Fix

• Two Modes • 16-bit High Precision Angle Sensor

• Adjustable Height & Angle • Adaptable Brake Force & Travel

• Direct connection to PC

Unscrew the nuts with two open-end wrenches counterclockwise, adjust the

lever's height and angle, and then tighten the screws. (It’s recommended to

apply the ﬂat and spring pads supplied in the tool kit to avoid scratches.)

1. Set the start and end points to adjust handbrake travel and eliminate

the dead zone.

2. Adjust the output curve to change the correlation between mechanical

travel and signal output at the initial and ﬁnal stages.

3. Click the calibration button and follow the instructions to re-calibrate if

you experience any handbrake output abnormalities.

4. Two mode options: on/off button mode or axis mode with continuous

brake travel.

Product specificaties

Merk:	MOZA
Categorie:	Controller
Model:	Hand Brake
Kleur van het product:	Zwart
Gewicht:	1700 g
Breedte:	330 mm
Diepte:	170 mm
Hoogte:	100 mm
Breedte verpakking:	238 mm
Diepte verpakking:	302 mm
Hoogte verpakking:	116 mm
Materiaal behuizing:	Aluminium
Stroombron:	Kabel
USB-connectortype:	USB Type-A, USB Type-B
Connectiviteitstechnologie:	Bedraad
Soort apparaat:	Handrem
Aansluiting:	USB
Gaming controle technologie:	Analoog/digitaal
Gaming controle functie toetsen:	Handremknop