Motorola Talkabout T465 Handleiding

Motorola Radio Talkabout T465

Lees hieronder de 📖 handleiding in het Nederlandse voor Motorola Talkabout T465 (4 pagina's) in de categorie Radio. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

TALKABOUT ® TWO-WAY RADIO

T4XX SERIES

*MN001126A01*

MN001126A01-AB

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks

or registered trademarks of Motorola Trademark Holdings, LLC and are used under

license. All other trademarks are the property of their respective owners.

Printed in China

For More Information

For further information, you may call Motorola Solutions at

1-800-448-6686 (Canada and U.S.), or visit us on the Internet at

www.motorolasolutions.com/talkabout.

RF Exposure and Product Safety Instructions for

Portable Two-Way Radios General Populated and

Uncontrolled Environments.

ATTENTION:

Before using this radio, refer to the important operating

instructions for safe usage and RF energy awareness and

control for compliance with applicable Standards and

Regulations.

Compliance with RF Exposure Standards

Your Motorola Two-Way radio complies with the following RF

energy exposure standard and guidelines:

• United States Federal Communications Commission,

Code of Federal Regulations; 47 CFR et seq. & FCC.

• Institute of Electrical and Electronic Engineers (IEEE)

C95.1.

• International Commission on Non-Ionizing Radiation

Protection (ICNIRP).

• Ministry of Health (Canada) Safety Code 6 & Industry

Canada RSS-102.

• Australian Communications Authority

Radiocommunications Standard et seq.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To

control your exposure and ensure compliance with the general

population/uncontrolled environment exposure limits, always

adhere to the following procedure:

• Transmit no more than 50% of the time.

• To receive calls, release the PTT button.

• To transmit (talk), press the Push-to-Talk (PTT) button in

front of the face.

• Hold the radio in a vertical position with the microphone

(and other parts of the radio including the antenna) at least

one inch (2.5 centimeters) away from the nose or lips.

Keeping the radio at a proper distance is important to

ensure compliance.

Note: RF exposure decreases with increasing distance from the

antenna.

• Body Worn Operation. When worn on the body, always

place the radio in a Motorola-approved clip, holder,

holster, case or body harness for this product.

Please refer to the following websites for more information on

what RF energy exposure is and how to control your exposure

to assure compliance with established RF exposure limits:

• http://www.fcc.gov/oet/rfsafety/rf-faqs.html

• www.who.int/en/

• http://responsibility.motorolasolutions.com/index.php/

downloads/dow07-rfexposureassessmentstand/

Two-way Radio Operation

• Use only Motorola-approved supplied or replacement

antennas, batteries, and audio accessories. Use of non-

Motorola-approved antennas, batteries, and wired or

wireless accessories may exceed the applicable RF

exposure guidelines (iEEE, ICNIRP or FCC).

• For a list of Motorola-approved accessories for your radio

model, visit the following website: http://

www.motorolasolutions.com/TalkaboutAccessories.

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately

shielded, designed or otherwise configured for

electromagnetic compatibility.

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received,

including interference that may cause undesired

operation.

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference received,

including interference that may cause undesired operation

of the device.

Facilities

To avoid electromagnetic interference and/or compatibility

conflicts, turn off your radio in any facility where posted notices

instruct you to do so. Hospitals or health care facilities may be

using equipment that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard an

aircraft. Any use of a radio must be in accordance with

applicable regulations per airline crew instructions.

Medical Devices – Pacemakers, Defibrillators or other

Implanted Medical Devices

Persons with pacemakers, Implantable cardioverter-

defibrillators (ICDs) or other active implantable medical devices

(AIMD) should:

• Consult with their physicians regarding the potential risk of

interference from radio frequency transmitters, such as

portable radios (poorly shielded medical devices may be

more susceptible to interference).

• Turn the radio OFF immediately if there is any reason to

suspect that interference is taking place.

• Do not carry the radio in a chest pocket or near the

implantation site, and carry or use the radio on the

opposite side of their body from the implantable device to

minimize the potential for interference.

Hearing Aids

Some digital wireless radios may interfere with some hearing

aids. In the event of such interference, you may want to consult

your hearing aid manufacturer to discuss alternatives.

Other Medical Devices

If you use any other personal medical device, consult the

manufacturer of your device to determine if it is adequately

shielded from RF energy. Your physician may be able to assist

you in obtaining this information.

Use of Communication Devices While Driving

Always check the laws and regulations on the use of radios in

the areas where you drive.

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a

call, if driving conditions or regulations so require.

For Vehicle With Air Bags

Refer to the vehicle manufacturer’s manual prior to installation

of electronic equipment to avoid interference with air bag wiring.

Do not place a portable radio in the area over an air bag or in

the air bag deployment area. Air bags inflate with great force. If

a portable radio is placed in the air bag deployment area and the

air bag inflates, the radio may be propelled with great force and

cause serious injury to occupants of the vehicle.

Potentially Explosive Atmosphere

Turn off your radio prior to entering any area with a potentially

explosive atmosphere. Only radio types that are especially

qualified should be used in such areas as “Intrinsically Safe”. Do

not remove, install or charge batteries in such areas. Sparks in a

potentially explosive atmosphere can cause an explosion or fire

resulting in bodily injury or even death.

Note: The areas with potentially explosive atmosphere referred

to above include fueling areas such as below decks on

boats, fuel or chemical transfer or storage facilities, areas

where the air contains chemicals or particles (such as

grain, dust or metal powders) and any other area where

you would normally be advised to turn off your vehicle

engine. Areas with potentially explosive atmospheres are

often – but not always posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off

your radio when you are near electrical blasting caps, in a

blasting area, or in areas posted “Turn off two-way radios”. Obey

all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna.

If a damaged antenna comes into contact with your skin, a

minor burn can result.

Batteries

All batteries can cause property damage and/or bodily injury

such as burns if a conductive material touches exposed

terminals. The conductive material may complete an electrical

circuit (short circuit) and become hot.

• Exercise care when removing NiMH or AA batteries. Do

not use sharp or conductive tools to remove these

batteries.

• Exercise care in handling any charged battery, particularly

when placing it inside a pocket, purse or other container

with metal objects.

• Do not discard your battery in a fire.

• Do not replace the battery in any area labeled “Hazardous

Atmosphere”. Any sparks created in a potentially

explosive atmosphere can cause explosion or fire.

• Do not disassemble, crush, puncture, shred or otherwise

attempt to change the form of your battery.

• Do not dry a wet battery or damp battery with an appliance

or heat source, such as a hair dryer or microwave oven.

• If the radio battery contact area has been submerged in

water, dry and clean the battery contacts before attaching

the battery to the radio.

Battery Charger Safety Instructions:

Save these Instructions

1. Turn the radio off when charging the battery.

2. Do not expose the charger to outside environment.

Chargers should only be used indoors.

3. Do not operate or disassemble the charger. Do not use a

charger that has been dropped or damaged in any way.

4. Never alter the AC cord or plug provided with the unit. If

the plug will not fit the outlet, have the proper outlet

installed by a qualified electrician. An improper condition

can result in a risk of electric shock.

5. To reduce the risk of damage to the cord or plug, pull the

plug rather than the cord when disconnecting the charger

from the AC receptacle.

6. To reduce the risk of electric shock, unplug the charger

from the outlet before attempting any maintenance or

cleaning.

7. Use of an attachment not recommended or sold by

Motorola Solutions may result in a risk of fire, electric

shock or personal injury.

8. Make sure the cord is located so it will not be stepped on,

tripped over or subjected to damage or stress.

9. An extension cord should not be used unless absolutely

necessary. Use of an improper extension cord could result

in a risk of a fire and/or electric shock. If an extension cord

must be used, make sure that:

• The pins on the plug of the extension cord are the same

number, size and shape as those on the plug of the

charger.

• The extension cord is properly wired and in good

condition.

• The extension cord size is 18 AWG for lengths up to 100

feet, and 16 AWG for lengths up to 150 feet.

10. The supply cord of the AC adaptor cannot be replaced. If

the cord is damaged, call customer service at

1-800-448-6686 (Canada and U.S.).

Your Motorola Solutions radio operates on General Mobile

Radio Service (GMRS) frequencies and is subject to the Rules

and Regulations of the Federal Communications Commission

(FCC).

The FCC requires that all operators using GMRS frequencies

obtain a radio license before operating their equipment. To

obtain the FCC forms, please visit the FCC website at

wireless.fcc.gov/uls/index.htm?job=home to source form 605

and 159, which includes all the instructions you will need.

If you wish to have the document faxed or mailed, or if you have

questions, please use the following contact information:

Changes or modifications not expressly approved by Motorola

Solutions may void the user authority granted by the FCC to

operate this radio and should not be made. To comply with FCC

requirements, transmitter adjustments should be made only by

or under the supervision of a person certified as technically

qualified to perform transmitter maintenance and repairs in the

private land mobile and fixed services as certified by an

organization representative of the user of those services.

Replacement of any transmitter component (crystal,

semiconductor, etc) not authorized by the FCC equipment

authorization for this radio could violate FCC rules.

Note: Use of this radio outside the country where it was

intended to be distributed is subject to government

regulations and may be prohibited.

Weatherproof

This radio is weatherproof to IP-54 standards. It is dust/

splashproof from any direction. The radio is resistant to water

and rain splashes only when the battery cover, headset

accessory port, and micro-USB ports are sealed. Open the

battery compartment door or headset port cover only when the

radio is dry. Use of a headset accessory should be in dry

environments only.

The micro-USB adaptor is not waterproof. Do not expose to rain

or snow. Charge the radios only in a dry location. Do not charge

wet radios. The battery door must be tightly closed with the

screw to maintain the weatherproof seal of the radio.

Installing the Batteries

Each radio can use either 1 NiMH rechargeable battery pack or

3 AA alkaline batteries and beeps when the batteries are low.

Installing the NiMH Rechargeable Battery Pack

(Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Remove the NiMH battery pack from the clear plastic bag

(do not disassemble or unwrap the battery pack).

4. Insert the NiMH battery pack with the diagram facing you.

(The ribbon should be underneath the battery pack and

should wrap around the right side of the pack for easy

removal).

5. Close the battery cover and tighten the retaining screw on

the battery cover.

Installing the Three AA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery cover

latch up and remove the cover.

3. Insert the three AA Alkaline batteries with + and – polarity

as shown inside. (The ribbon should be underneath the

AA alkaline batteries and should wrap around the right

side of the batteries).

4. Close the battery cover and tighten the retaining screw on

the battery cover.

Radio Battery Meter

The radio battery icon shows the battery charge level, from full

to empty . When the radio has one segment left,

the radio chirps periodically or after releasing the PTT button

(Low Battery Alert).

Removing the NiMH Battery Pack

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Remove the NiMH battery pack by pulling the ribbon

attached to the radio.

4. Close the battery cover and tighten the retaining screw on

the battery door.

Removing the Three AA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Gently remove each alkaline battery by easing each

battery out individually.

4. Close the battery cover and tighten the retaining screw on

the battery door.

Note:

• Exercise care when removing NiMH or AA batteries. Do

not use sharp or conductive tools to remove either of

these batteries.

• Remove the batteries before storing your radio for

extended periods of time. Batteries corrode over time and

may cause permanent damage to your radio.

Battery Capacity Maintenance

1. Charge the NiMH batteries once every 3 months when not

in use.

2. Before placing the radio in storage, remove the battery.

3. Store the NiMH batteries in temperature between -20 °C to

35 °C and in low humidity. Avoid damp conditions and

corrosive materials.

Using the Micro-USB Charger

The micro-USB charger is a handy port that allows you to

conveniently charge your NiMH battery pack.

1. Make sure your radio is turned OFF.

2. Plug the micro-USB cable into the micro-USB charging

port on your radio. Connect the other end of the micro-

USB charger to wall power outlet.

3. An empty battery will be fully charged in 14 hours.

4. The battery meter on LCD will move to indicate the battery

is charging.

Note:

• It is recommended to power OFF your radio while

charging. However, if power is turned on while charging,

you may not be able to transmit a message if the battery is

completely empty. Allow time for the battery to charge to 1

bar before attempting to transmit a message.

• When moving between hot and cold temperatures, do not

charge the NiMH battery pack until the battery

temperature acclimates (usually about 20 minutes).

• For optimal battery life, remove the radio from the charger

within 16 hours. Do not store the radio while connected to

the charger.

Attaching and Removing the Belt Clip

1. Attach the belt clip to the Talkabout plate at the back of the

radio until the clip clicks in place.

2. Attach the belt clip to pocket or belt strap until the clip

clicks in place.

To Remove

1. Push the release tab on top of the belt clip to release the

latch.

2. Pull the belt clip away from the back of the radio.

Turning your Radio On and Off

Turn clockwise to turn the radio on and counterclockwise to

turn the radio off.

1. In the ON position, the radio chirps and briefly shows all

feature icons available on the radio.

2. The display screen then shows the current channel, code

and all features that are enabled. The radio is now in

Two-Way mode.

Setting the Volume

Press and hold for three seconds while rotating until you

reach a comfortable listening level.

1. Rotate clockwise to increase the volume.

2. Rotate counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

To communicate, all radios in your group must be set to the

same channel and Interference Eliminator Code.

1. To talk, press and hold the PTT button. When transmitting,

icon blinks and is shown. If it is a high

power transmission, is shown. If it is a low power

transmission, is shown.

2. When you are finished talking, release the PTT button.

3. When receiving, icon blinks and is

shown. If it is a high power channel, is shown. If it is a

low power channel, is shown.

For maximum clarity, hold the radio two to three inches away

from your mouth and speak directly into the microphone. Do not

cover the microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet

apart.

Power Boost

To boost the power of your radio to high power, press the top

portion of the PTT button when talking. If you know your party is

close by, you can conserve the energy of your battery by

pushing the lower part of the PTT button to use less power.

Note: If you are on an FRS only channel (see “Channels and

Frequencies”) the radio will only use low power when

either portion of the PTT button is pressed.

Power Boost is not applicable for model T400.

Monitor Button

Pressing and holding for three seconds allows you to listen

to the volume level of the radio when you are not receiving. This

allows you to adjust the volume, if necessary. You can also

press to check for activity on the current channel before you

talk.

Push-to-Talk Timeout Timer

To prevent accidental transmissions and save battery life, the

radio emits a continuous warning tone and stops transmitting if

you press the PTT button for 60 continuous seconds.

Mode Button

By pressing “mode” button, the user will be seamlessly

switching between two-way and weather mode. When radio is in

two-way mode, will be shown. When radio is in

weather mode, will be shown. Corresponding

setting and information will be shown on the LCD.

Selecting the Channel

Your radio has 22 channels. The channel is the frequency the

radio uses to transmit. Channels 8-14 are FRS 0.5 watt only and

all other channels are GMRS. (See the “Channels and

Frequencies” table on overleaf for details).

1. With the radio on, press until the channel number

starts to flash. When the radio is on a 0.5 watt channel,

display shows . When the radio is on a 1.5 watts

channel, display shows . The current channel flashes.

2. Press or and select an unused or quiet channel.

3. Press the PTT button to save the channel setting or to

continue set up.

Selecting the Interference Eliminator Code

Interference Eliminator Codes help minimize interference by

blocking transmissions from unknown sources. Your radio has

121 Interference Eliminator Codes. Codes 1 – 38 are standard

analog codes that appear on other FRS/GMRS radios. Codes

39 – 121 are additional digital codes added for superior

interference protection. 0 is the off position, no analog or digital

codes are enabled.

To set the code for a channel:

1. Press until the code starts to flash.

2. Press or to select the code.

3. Press the PTT button to save the code setting or to

continue set up.

You can set a different code for each channel using this

procedure. An extended press of or allows you to scroll

through the Interference Code rapidly so you can quickly reach

the code you want.

Note: On a radio that uses Interference Eliminator Codes, the

code must be set to 0 to communicate with radios that do

not have Interference Eliminator Codes. Select 0 for “no

tone, no code” on the display of your radio.

Safety and General Information

For a fax:

Contact the Fax-On-

Demand system

For mail service:

Call the FCC Forms

Hotline

If you have questions

about the FCC License:

Call the FCC

1-202-418-0177 1-800-418-FORM (3676) 1-888-CALL-FCC

(225-5322)

FCC Licensing Information

Control Buttons

MODE

Volume/Power

Push-to-Talk (High)

Mode Switch

Call Tone

Emergency

Button

Screen

Scan/Monitor

Menu/Lock

Flashlight LED

Accessory Port

Flashlight Button

Speaker

Microphone

Micro-USB

Charging Port

Push-to-Talk (Low)

Display Screen Guide

Numbers for Channel,

Call Tone

Numbers for Codes

Battery Meter

Weather Alert

Lock

Noise Filtering

Scan

Vibracall

Call Tone

iVOX / VOX

Battery Save

Roger Tone

Keypad Tone

Power (high-low)

Status (transmit/

receive)

Getting Started

Talking and Listening

Menu Options

MN001126A01_ab.fm Page 2 Thursday, March 12, 2015 1:41 PM

Setting and Transmitting Call Tones

Your radio can transmit different call tones to other radios in

your group so you can alert them that you want to talk. Your

radio has 20 call tones from which to choose.

To set a call tone:

1. Press until appears. The current call tone setting

will flash.

2. Press or to change and hear the call tone.

3. Press the PTT button to set the new call tone or to

continue set up.

To transmit your call tone to other radios set up to the same

channel and Interference Eliminator Code as your radio, press

Note: Setting the call to OFF disables the call tone feature.

Hands-Free Use Without Accessories ( )

You can use the feature to transmit hands-free without

the need for any headset accessories. Once is turned on,

the radio detects your voice and transmits when you speak into

the internal microphone.

1. Press until appears on the display. The current

setting will flash.

2. Press or to select On or Off or set sensitivity L1,

L2 or L3.

3. Press the PTT button to set or to continue set up.

Hands-Free Use with Accessories ( )

You can transmit hands-free more reliable with the use of

optional headset accessories. Once is turned on, the

radio detects your voice and transmits when you speak.

Many accessories (sold separately) are available for your radio.

For more information, visit our website at

www.motorolasolutions.com/TalkaboutAccessories or call

1-800-448-6686.

1. Turn the radio off and plug the accessory into the

accessory port.

2. Turn the radio on. shows on the display.

3. Adjust the volume appropriately by rotating . Lower the

volume before placing the accessory on your head or in

your ear.

4. To turn off, simply remove accessory.

Note: There is a short delay between the time you start talking

and when the radio transmits. There is a short delay

before the transmission is completed.

Setting the Sensitivity Level When in Mode

Adjusting the sensitivity level of the radio helps minimize the

possibility of unintended noises triggering a transmission and

helps the radio pick up soft voices.

1. Press until appears. The current setting

(L1 – L3) will flash.

2. Press or to select the sensitivity level.

3. Press the PTT button to set or to continue set up.

Note: When you connect a headset, the radio is automatically

set to the last chosen sensitivity level.

Setting the Extended Battery Save Level ( )

This feature puts the radio into a low power “sleep” mode for

cycle periods of 1, 2 or 3 seconds. The radio will briefly check

for any channel activity after each sleep cycle. The sleep cycle

repeats until a key is pressed or a call is received.

1. Press until appears. The current setting (L0, L1,

L2 or L3) will flash.

2. Press or to select the battery save level.

3. Press the PTT button to set or to continue set up.

Note:

1. Signals received during the sleep period will not be heard

until after the timer period expires. The first 1 – 3 seconds

of speech can be missed. Do not use (battery save)

L1, L2 or L3 settings when immediate response may be

required.

2. , , and modes are not available with

extended battery save mode. Using , , or

enabling will necessarily disable the extended sleep

cycle battery settings.

3. Maximum battery life savings may be achieved only when

usage is primarily in standby mode and very little TX or RX

(talking or listening) use occurs. When RX or TX are often

used, little or no battery life extension will occur.

Noise Filtering

The noise-filtering feature helps to ensure uninterrupted

communication with other Motorola Solutions radios that have

this feature. This feature also filters out unwanted transmissions

from other radios. This is useful in places where there is heavy

radio traffic, such as amusement parks or ski resorts.

Note: noise filtering is not available when the radio is

scanning. noise filtering is not available when

extended battery save is set to L1, L2 or L3. In

consequence the will not appear in the Menu. You

must set extended battery save to L0 in order to activate

noise filtering.

To turn on or off:

1. Press until displays. The current setting On/Off will

flash.

2. Press or to select On or Off.

3. Press the PTT button to set or to continue set up.

To transmit to a radio that has noise filtering turned on:

1. Select the same channel and Interference Eliminator

Code as the other radio.

2. Press to send a call tone. This allows your voice to

pass through the noise filter on the receiving radio.

3. Press the PTT button and speak normally.

Note: Without first pressing , your message will not be

heard. After this, for a 30-second period, starting after the

last transmission, all transmissions received on the

selected channel and code will pass through the noise

filter. When radio goes to idle, will need to be pressed

again to allow communication to pass through.

VibraCallTM Alert

VibraCall TM is a vibrating alert that notifies you that your radio is

receiving a message. This is useful in noisy environments.

When the alert is on, the radio vibrates once every 30 seconds

when you receive a message on the channel and code you set.

1. To turn vibrating alerts on, press until is displayed.

The current setting will flash.

2. Press or to change the setting to On/Off.

3. Press the PTT button to confirm or to continue set up.

Note: VibraCall TM Alert is not applicable for model T400.

Keypad Tones

You may enable or disable the speaker key tones. You will hear

the key tone each time a button is pushed.

1. Press until appears. The current setting On/Off will

flash.

2. Press either or to turn On or Off.

3. Press the PTT button to confirm or to continue set up.

Note: When the key tone feature is off, the following are not

disabled:

• Transmit timeout alert tone

• Call tone

• Low battery alert tone or

• The transmitted talk confirmation tone

Transmitting a Talk Confirmation Tone

You can set your radio to transmit a unique tone when you finish

transmitting. It is like saying “Roger” or “Over” to let others know

you are finished talking.

1. With the radio on, press until the appears. The

current setting On/Off flashes.

2. Press or to turn On or Off.

3. Press the PTT button to set or to continue set up.

Emergency Alert Mode

The Emergency Alert feature can be used to signal members in

your group of your need for urgent help. T4XX series radios will

operate in an automatic “hands-free” emergency control mode

for a total of 30 seconds after activating the Emergency Alert.

T4XX series radios in your group will automatically advance the

speaker volume to the maximum setting and sound a warbling

alert tone for 8 seconds. The alert tone is emitted from your own

radio speaker and the receiving radios in your group. After the 8

second alert, any spoken words or incidental sounds at your end

will be transmitted to the group for 22 seconds. For the 30

second duration of Emergency Alert mode, T4XX series radio

controls and buttons will be locked to maximize reception of the

emergency message.

1. Press and hold the Emergency Alert button for 3 seconds.

2. Release the button the alert tone begins to sound. There

is no need to continue to hold the Emergency Alert button

or use PTT for your message to be transmitted.

3. After the alert tone ends you may speak into the

microphone. Your voice or incidental sounds will be

transmitted.

4. After 30 seconds your radio speaker will emit a Talk

Confirmation Tone. Operation then returns to normal

two-way mode.

Note: All Motorola Talkabout EM, MJ, MR, MT, MU and T4XX

series radios (except for model T400) are fully compatible

with the Emergency Alert feature. Radios other than EM,

MJ and MR series can receive the emergency alert

signal, but will not respond with adjusted volume settings,

locked controls or a warbling alert tone. Users of other

radio models set to the same channel and Interference

Eliminator Code will hear a steady tone for 8 seconds

followed by the voice transmission for 22 seconds.

Built-in LED Flashlight with Power Outage Function

Press the flashlight button to turn and keep the light on. Press

the flashlight button again, the light is off.

Note: Turn off the flashlight when not in use to conserve battery

power.

Keypad Lock

To avoid accidentally changing your radio settings:

1. Press and hold until displays.

2. When in lock mode, you can turn the radio on and off,

adjust the volume, receive, transmit, send a call tone and

monitor channels. All other functions are locked.

3. To unlock the radio, press and hold until is no

longer displayed.

Scanning Channels

Use scan to search the 22 channels for transmissions from

unknown parties, to find someone in your group who has

accidentally changed channels or to quickly find unused

channels for your own use.

There is a priority feature and 2 modes of scanning (basic and

advanced) to make your search more effective. The basic scan

mode uses the channel and code combinations for each of the

22 channels as you have set them (or with the default code

value of 1). The “Advanced Scan” mode will scan all channels

for any and all codes, detect any code in use and use that code

value temporarily for that channel.

Priority is given to the “home channel”, that is, the channel (and

Interference Eliminator Code) your radio is set to when you start

the scan. This means the initial channel (and code settings) is

scanned more often than the other 21 channels and your radio

will respond quickly to any activity occurring on the home

channel as a priority.

To start Scanning:

1. Briefly press the key. The scan will appear in the

display and the radio will begin to scroll through the

channel and code combinations.

2. When the radio detects channel activity matching the

channel and code combination, it stops scrolling and you

can hear the transmission.

3. To respond and talk to the person transmitting, press the

PTT button within five seconds after the end of the

transmission.

4. The radio will resume scrolling through the channels five

seconds after the end of any received activity.

5. To stop scanning, briefly press the key.

To start Advanced Scanning

1. Set the Interference Eliminator Code to “zero” or OFF.

2. Briefly press the key. The scan will appear in the

display and the radio will begin to scroll through the

channels. No Interference Eliminator Codes will filter what

is heard.

3. When the radio detects channel activity with ANY code (or

NO code), it stops scrolling and you can hear the

transmission. Any Interference Eliminator Code that may

be in use by that party will be detected and displayed.

4. To respond and talk to the person transmitting, press the

PTT button within five seconds of the end of the

transmission. The radio will transmit using the newly

detected Interference Eliminator Code.

5. The radio will resume scrolling through the channels five

seconds after the end of any received activity.

6. To stop scanning, briefly press the .

Scanning Notes:

1. If you press the PTT button while the radio is scrolling

through inactive channels, the transmission will be on the

“home channel”. Scanning will resume five seconds after

the end of your transmission. You may press the key

to stop scanning at any time.

2. If the radio stops on an undesired transmission, you may

immediately resume the scan by briefly pressing or

3. If the radio repeatedly stops on an undesired

transmission, you may temporarily remove that channel

from the scan list by pressing and holding or for

three seconds. You may remove more than one channel in

this way.

4. To restore the removed channel(s) to the scan list, turn the

radio off and then turn back on, or exit and re-enter the

scanning mode by pressing .

5. You cannot remove the home channel from the scan list.

6. In Advanced Scan, the detected code will only be used for

one transmission. You must note that code, exit scan and

set that detected code on that channel to permanently use

the detected code.

Your radio can tune in to broadcasts by the United States

National Oceanic and Atmospheric Administration (NOAA)

Weather Radio and Environment Canada Weather Radio.

You can listen to a weather channel (see “Weather Channels

and Frequencies” table for details) or set your radio to alert you

to emergency weather broadcasts that interrupt routine

broadcasts. When you listen to a weather channel, you cannot

use your radio in scan mode or for two-way communications.

Both NOAA and Environment Canada have transmitters located

throughout the United States and Canada, respectively. These

transmitters broadcast watches, forecasts and other information

24 hours a day.

Note: NOAA weather radio stations are assigned to cover

specific areas and service may be limited. Please check

with your local weather office for frequency and details or

visit www.weather.gov/nwr in the US to view the

appropriate transmitter for your area. The use of the

NOAA logo does not provide an endorsement or implied

endorsement by the National Weather Service of NOAA,

nor does the use of the Weatheradio logo provide an

endorsement or implied endorsement by Environment

Canada.

Entering Weather Mode

1. From two-way mode, press to enter weather mode

Setting the Weather Channel

Your radio receives weather frequencies:

1. In weather mode, press until weather channel number

flashes.

2. Press or to select the appropriate channel with

good reception in your area.

3. Press the PTT button to set or to continue set up

weather alert.

Setting the Weather Alert

Your radio can be set to respond to NOAA Weather Radio

emergency messages. A special alarm tone sounds an alert and

turns on the weather receiver to give you immediate weather

and emergency information.

1. In weather mode press twice until displays.

2. Press or to select On/Off.

3. Press the PTT button or to exit the weather menu set

up.

4. Press to return to two-way mode. If you activate

Weather Alert and return to two-way mode will

display.

Note:When the weather channel is activated, either manually or

after receiving an alert, and no buttons are pressed for 5

minutes, the weather mode will automatically revert back

to two-way mode.

As with two-way radio reception, weather channel reception

depends on how close you are to a transmitter and whether you

are indoors or outdoors. Because weather channels are

transmitted without codes, they may contain static or noise.

Weather Alert will not function while actively transmitting or

receiving in two-way mode.

Weather Channels and Frequencies

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the

Stylized M logo are trademarks or registered trademarks of

Motorola Trademark Holdings, LLC and are used under license.

All other trademarks are the property of their respective owners.

Consumer Two-Way Radio Products and

Accessories purchased in the United States or

Canada

What Does this Warranty Cover?

Subject to the exclusions contained below, Motorola Solutions,

Inc. (“Motorola”) warrants the Motorola branded consumer

two-way radios that operate via Family Radio Service or

General Mobile Radio Service (“Products”), the Motorola

branded or certified accessories sold for use with these

Products (“Accessories”) to be free from defects in materials

and workmanship under normal consumer usage for the

period(s) outlined below. This limited warranty is the exclusive

remedy of a consumer, and applies as follows to new Products

and Accessories and purchased by consumers in the United

States or Canada, which are accompanied by this written

warranty:

Who is Covered?

This warranty extends only to the first consumer purchaser, and

is not transferable.

What will MOTOROLA SOLUTIONS, INC. do?

Motorola Solutions, Inc., at its option, will at no charge repair,

replace or refund the purchase price of any Products or

Accessories that do not conform to this warranty. We may use

functionally equivalent reconditioned/ refurbished/ pre-owned or

new Products or Accessories.

What Other Limitations Are There?

Any Implied Warranties, Including Without Limitation

The implied warranties of merchantability and fitness for a

particular purpose, shall be limited to the duration of this limited

warranty, otherwise the repair, replacement, or refund as

provided under this express limited warranty is the exclusive

remedy of the consumers, and is provided in lieu of all other

warranties, express or implied. In no event shall Motorola

Solutions be liable, whether in contract or tort (including

negligence) for damages in excess of the purchase price of the

product or accessory, or for any indirect, incidental, special or

consequential damages of any kind, or loss of revenue or

profits, loss of business, loss of information or other financial

loss arising out of or in connection with the ability or inability to

use the products or accessories to the full extent these

damages may be disclaimed by law.

Some states and jurisdictions do not allow the limitation or

exclusion of incidental or consequential damages, or limitation

on the length of an implied warranty, so the above limitations or

exclusions may not apply to you. This warranty gives you

specific legal rights, and you may also have other rights that

vary from state to state or from one jurisdiction to another.

How to Obtain Warranty Service or Other

Information?

To obtain service or information, please call

USA and Canada Two-Way Radios

1-800-448-6686.

www.motorolasolutions.com/talkabout

For Accessories:

Please call the telephone number designated above for the

Product with which they are used.

You will receive instructions on how to ship the Products or

Accessories at your expense, to Motorola or a Motorola

Authorized Repair Center. To obtain service, you must include:

(a) a copy of your receipt, bill of sale or other comparable proof

of purchase; (b) a written description of the problem; (c) the

name of your service provider, if applicable; (d) the name and

location of the installation facility (if applicable) and, most

importantly; (e) your address and telephone number.

For more information, please visit us at:

L3 = High Sensitivity for quiet environments

L2 = Medium Sensitivity for most environments

L1 = Low Sensitivity for noisy environments

L0 = Normal battery save mode

L1 = 1 second extended battery save mode (low setting)

L2 = 2 seconds extended battery save mode (mid setting)

L3 = 3 seconds extended battery save mode (max setting)

Special Features

WARNING: The Emergency Alert feature should only be

used in the event of an actual emergency.

Motorola Solutions is not responsible if there is

no response to the emergency alert from the

receiving group.

Weather Channel Frequency Weather Channel Frequency

WX1 162.550 MHz WX7 162.525 MHz

WX2 162.400 MHz WX8 161.650 MHz

WX3 162.475 MHz WX9 161.775 MHz

WX4 162.425 MHz WX10 161.750 MHz

WX5 162.450 MHz WX11 162.000 MHz

WX6 162.500 MHz

Channel ChannelFrequency Description Frequency Description

1 462.5625 MHz GMRS/FRS 12 467.6625 MHz FRS

2 462.5875 MHz GMRS/FRS 13 467.6875 MHz FRS

3 462.6125 MHz GMRS/FRS 14 467.7125 MHz FRS

4 462.6375 MHz GMRS/FRS 15 462.5500 MHz GMRS

5 462.6625 MHz GMRS/FRS 16 462.5750 MHz GMRS

6 462.6875 MHz GMRS/FRS 17 462.6000 MHz GMRS

7 462.7125 MHz GMRS/FRS 18 462.6250 MHz GMRS

8 467.5625 MHz FRS 19 462.6500 MHz GMRS

9 467.5875 MHz FRS 20 462.6750 MHz GMRS

10 467.6125 MHz FRS 21 462.7000 MHz GMRS

11 467.6375 MHz FRS 22 462.7250 MHz GMRS

Weather Receiver

MODE

Channels and Frequencies

Products Covered Length Of Coverage

Products and

Accessories

as defined above, unless

otherwise provided for

below: One (1) year from the date of

purchase by the first consumer

purchaser of the product unless

otherwise provided for below.

Batteries

whose fully charged

capacity falls below 80% of

their rated capacity and

batteries that leak

Products and

Accessories

that are repaired or

replaced

The balance of the original

warranty or for ninety (90) days

from the date returned to the

consumer, whichever is longer.

Patent and Copyright Information

Warranty

Exclusions From Warranty Coverage

Normal Wear and Tear:

Periodic maintenance, repair and replacement of Products or

Accessories due to normal wear and tear.

Abuse & Misuse:

Defects or damage that result from: (a) improper operation,

storage, misuse or abuse, accident or neglect, such as

physical damage (cracks, scratches, etc.) to the surface of the

Products and Accessories resulting from misuse; (b) contact

with liquid, water, rain, extreme humidity or heavy perspiration,

sand, dirt or the like, extreme heat, or food; (c) use of the

Products or Accessories for commercial purposes or

subjecting the Product or Accessory to abnormal usage or

conditions; or (d) other acts which are not the fault of Motorola.

Use of Non-Motorola branded Products and Accessories:

Defects or damage that result from the use of Non-Motorola

branded or certified products, accessories, software or other

peripheral equipment.

Unauthorized Service or Modification:

Defects or damages resulting from service, testing,

adjustment, installation, maintenance, alteration, or

modification in any way by someone other than Motorola or its

authorized service centers.

Altered Products:

Products or Accessories with (a) serial numbers or date tags

that have been removed, altered or obliterated; (b) broken

seals or that show evidence of tampering; (c) mismatched

board serial numbers; or (d) nonconforming or non-Motorola

branded housings, or parts.

Communication Services:

Defects, damages, or the failure of Products or Accessories

due to any communication service or signal you may subscribe

to or use with the Products or Accessories.

https://www.facebook.com/

MotorolaTalkaboutWalkieTalkies

http://bit.ly/Talkabout

www.motorolasolutions.com/talkabout

Product specificaties

Merk:	Motorola
Categorie:	Radio
Model:	Talkabout T465

Heb je hulp nodig?

Als je hulp nodig hebt met Motorola Talkabout T465 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Radio Motorola

Motorola Talkabout T460 Handleiding

8 December 2024

Motorola MOTOTRBO SL300 Handleiding

8 December 2024

Motorola APX 8000XE Handleiding

24 September 2024

Motorola APX 8000HXE Handleiding

15 Maart 2024

Motorola MOTOTRBO R2 Handleiding

22 Februari 2024

Motorola MOTOTRBO R7 Handleiding

22 Februari 2024

Motorola MOTOTRBO Ion Handleiding

22 Februari 2024

Motorola Talkabout T270 Handleiding

16 Mei 2023

Motorola Talkabout T465 Handleiding

11 Mei 2023

Motorola Talkabout T280 Handleiding

9 Mei 2023

Handleiding Radio

Nieuwste handleidingen voor Radio

Midland XT50 Handleiding

20 December 2024

Elbe RF-942 Handleiding

18 December 2024

Alba NE-6207 Handleiding

18 December 2024

Albrecht Tectalk biz Handleiding

16 December 2024

Albrecht Tectalk Easy 3 Handleiding

16 December 2024

Albrecht Tectalk Duo Handleiding

16 December 2024

Pure Classic H4 Handleiding

13 December 2024

Blonder Tongue BIDA 86B-30P Handleiding

10 December 2024

Blonder Tongue BIDA 86B-43P Handleiding

10 December 2024

Blonder Tongue AP-60-860A Handleiding

10 December 2024