MOTO Reflex Handleiding

MOTO Fietsaccessoire Reflex

Lees hieronder de 📖 handleiding in het Nederlandse voor MOTO Reflex (2 pagina's) in de categorie Fietsaccessoire. Deze handleiding was nuttig voor 66 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Please read this manual properly before use and follow all the instructions

carefully.

Once you have read the manual you should store it in a safe place for

future reference.

You should only disassemble the pedals if you are familiar with the

technology and if you have all the necessary tools at hand.

Motobicycles-36 UG

Berlin, Germany

www.motobicycles.com

support@motobicycles.com

Thank you for choosing the MOTO Pedal. This manual has been designed

to assist you with technical support. Should you have any questions please

check this manual and if necessary contact an experienced bicycle mechanic or

support@motobicycles.com.

The MOTO Pedal is manufactured completely in Germany to the highest

quality requirements and assembled carefully by hand. However, should you

have reason to complain please contact your bicycle dealer or the MOTO

customer support team.

MOTO quality Safety notes

Reex Cycling Pedal

Manual

German patent and foreign patents pending

Safety notes

Please note that the pedals need to be driven for 50 to 100 km before the slide

bearings reach their nal smoothness.

For information regarding pedal maintenance, please read the instructions

below or visit our website. Please note that the pedals are not designed for

competition use.

We recommend lubricating the bearings with BERULUB FR 16 or equivalent

lightweight, silicone-free, synthetic special grease with PTFE additives.

Contents

2 MOTO Pedals

4 Reex Tapes Allen Key 3 mm

Construction Initial adjustments

Stick the MOTO Reex Tapes into

the designated areas.

Make sure the areas are clean.

Dismount the current pedals.

Clean the crank thoroughly, especially the thread of the pedal crank arm.

FasteningAssembly tool

When mounting the pedal, please follow the installation instructions

and the suggested torque strength given by the crank arm manufacturer!

The pedal shaft terminates

in an 8 mm hex socket.

An 8 mm Allen key is needed to

mount the pedals on the crank arms.

Griptape pad

Plastic

half-shell

Threaded

metal shaft

Plastic

half-shell

Screws

O-Ring

Nuts

Right pedal

Attention! The right pedal has a right hand thread and the left pedal

has a left hand thread at the pedal shaft for mounting on the crank arm.

Designed in Berlin

Engineered, produced and

assembled in Germany

Left pedal

The left pedal is further identiable by a groove / letter on the

pedal collar.

Right

Left

If the pedals develop a slight clicking sound after intensive use, this indicates

that the bearings should be retightened. Please proceed as described in

maintenance.

Slight clicking

Maintenance and care

Pedal width-adjustment

To maintain optimal functionality of the pedals, they should be serviced every

few hundred kilometers. This is done in a few simple steps and takes less than

5 minutes. To allow servicing if required, the Griptape pads are designed to be

reused several times according to the state of their wearout.

1. Remove Griptape (see diagram to the right)

Heat Griptape with a hair dryer for a few seconds and remove it carefully.

2. Seperate half-shells

Use the Allen key 3mm, included in the package to unscrew the half-shells.

Apply heat with a hair dryer in order to remove Griptape.

Fitting O-ring into designated grooves and tightening half-shells.

5. Apply Griptape

Stick on new or used MOTO Griptape pads on the top and bottom sides

of the pedals.

3. Grease pedal shaft

Clean and grease pedal shaft sufciently. We recommend lubricating the

slide bearings with BERULUB FR 16 or equivalent lightweight, silicone-free,

synthetic special grease with PTFE additives.

4. Tighten half-shells (see diagram to the right)

Make sure the O-ring is tted into the designated grooves of the half-shells to

prevent damage. Tighten the screws of the plastic half-shells with a torque of

120-150 Ncm. You can use the Allen key, included in the package.

Find more useful hints at

www.motobicycles.com/faq-en.html

Distance between platform and crank arm can be extented or reduced by 5

mm. To adjust pedal width, unscrew half-shells and change position of the pedal

shaft; see also maintenance. This provides additional space for large shoes.

5 mm

Adjustment

5 mm

Product specificaties

Merk:	MOTO
Categorie:	Fietsaccessoire
Model:	Reflex
Kleur van het product:	Black, Orange
Breedte:	76 mm
Diepte:	92 mm
Aantal per verpakking:	2 stuk(s)
Antislipplatform:	Ja