Milwaukee M18 2688-21 Handleiding

Milwaukee Hittepistool M18 2688-21

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 2688-21 (16 pagina's) in de categorie Hittepistool. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

Cat. No. / No de cat.

2688-20

M18™ COMPACT HEAT GUN

COMPACT PISTOLET À DÉCAPER DE M18™

COMPACTO PISTOLA DE CALOR DE M18™

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

Original Instructions

Instructions originales

Instrucciones originales

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings, instruc-

tions, illustrations and specica-

tions provided with this power tool. Failure to

follow all instructions listed below may result in

electric shock, re and/or serious injury. Save all

warnings and instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-oper-

ated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

•

Indoor Use.

Do not expose power tools to rain

or wet conditions. Water entering a power tool will

increase the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the o󰀨-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your nger on

the switch or energizing power tools that have the

switch on invites accidents.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry or long hair

can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which

it was designed.

• Do not use the power tool if the switch does not

turn it on and o󰀨. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

• Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may a󰀨ect the power tool’s operation. If damaged,

have the power tool repaired before use. Many ac-

cidents are caused by poorly maintained power tools.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations di󰀨erent from those intended could

result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of re when used

with another battery pack.

• Use power tools only with specically designated

battery packs. Use of any other battery packs may

create a risk of injury and re.

• When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal

to another. Shorting the battery terminals together

may cause burns or a re.

• Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact ac-

cidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

• Do not use a battery pack or tool that is dam-

aged or modied. Damaged or modied batteries

may exhibit unpredictable behavior resulting in re,

explosion or risk of injury.

• Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or tem-

perature above 265°F (130°C) may cause explosion.

• Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specied in the instructions. Charging

improperly or at temperatures outside the specied

range may damage the battery and increase the risk

of re.

SERVICE

• Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

• Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SPECIFIC SAFETY RULES

FOR HEAT GUNS

READ THESE INSTRUCTIONS

• Know your work environment. Hidden areas such

as behind walls, ceilings, oors, so󰀩t boards and

other panels may contain ammable materials that

may ignite when using the heat gun in these loca-

tions. Ignition of these materials may not be readily

apparent and could result in property damage and

personal injury. Check these areas before applying

heat. If in doubt, use an alternate method. Pausing

or lingering in one spot may ignite the panel or the

material behind it. Keep heat gun moving to avoid

excessive temperatures.

• Do not direct the heat gun air airow at clothing,

hair or other body parts. Do not use as a hair

dryer. Heat guns can produce 1100°F (593°C) or

more of ameless heat at the nozzle. Contact with

the air stream could result in personal injury.

• Do not use near ammable liquids or in explosive

atmospheres, such as in the presence of fumes,

gases or dust. The ameless heat from the heat

gun may ignite the dust or fumes. Remove materials

or debris that may become ignited from work area.

• Shield materials around the heated area to pre-

vent property damage or re.

• Keep a re extinguisher nearby. Heat guns may

ignite ammable materials left in the work area.

• WARNING! Hot Surfaces. Always hold the heat

gun by the plastic enclosure. Do not touch

nozzle, accessory tips or store heat gun until

the nozzle has cooled to room temperature. The

metal nozzle requires approximately 20 minutes

to cool before it can be touched. Contact with the

nozzle or accessory tip could result in personal

injury. Place the heat gun in a clear area away from

combustible materials while cooling to prevent am-

mable materials from igniting.

• Do not cut o󰀨 airow by placing nozzle too close

to workpiece. Keep intake vents clean and clear of

obstructions. Restricting airow may cause the heat

gun to overheat.

• Place the heat gun on a stable, level surface

when not hand held.

• Do not leave the heat gun unattended while run-

ning or cooling down. Inattention invites accidents.

• Store indoors in a dry location. Do not expose to

rain or moisture.

• Do not direct airow directly on glass. The glass

may crack and could result in property damage or

personal injury.

• Always use common sense and be cautious when

using tools. It is not possible to anticipate every

situation that could result in a dangerous outcome.

Do not use this tool if you do not understand these

operating instructions or you feel the work is beyond

your capability; contact Milwaukee Tool or a trained

professional for additional information or training.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

•

WARNING

Some dust created by power sanding,

sawing, grinding, drilling, and other

construction activities contains chemicals known to

cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to

lter out microscopic particles.

IMPORTANT SAFETY INSTRUCTIONS

FOR REMOVING PAINT

WARNING

Use extreme care when stripping

paint. Peelings, residue and vapors

of paint may contain lead, which is POISONOUS.

Pre-1977 paint may contain lead and paint made

before 1950 is likely to contain lead. Hand to

mouth contact with paint peelings or residue from

pre-1977 paint may result in lead ingestion. Ex-

posure to even low levels of lead can cause ir-

reversible brain and nervous system damage.

Young and unborn children are especially vulner-

able to lead poisoning. DO NOT REMOVE LEAD-

BASED PAINT WITH A HEAT GUN. Before begin-

ning your work, determine whether the paint you

are removing contains lead. A local health depart-

ment or a professional who uses a paint ana-

lyzer can check the paint for lead content. LEAD-

BASED PAINT SHOULD BE REMOVED ONLY BY

A PROFESSIONAL.

Persons removing paint should follow these

guidelines:

• Work in a well ventilated area. If possible, move the

workpiece outdoors. If working indoors, open windows

and place an exhaust fan in a window. Be sure the fan

is moving air from inside to outside. Proper ventila-

tion will reduce the risk of inhaling chemicals found

in the fumes or dust created by using a heat gun.

• Remove or cover any carpets, rugs, furniture,

clothing, cooking utensils and air ducts to pre-

vent property damage from the paint peelings.

• Place drop cloths in the work area to catch paint

scrapings. Wear protective clothing such as hats,

extra work shirts and overalls. Paint scrapings may

contain chemicals that are hazardous.

• Work in one room at a time. Remove furnishings

or cover them and place in the center of the room.

Seal doorways with drop cloths to seal work area

from the rest of the building.

• Children, pregnant or potentially pregnant

women, and nursing mothers should not be near

work area until all work is completed and work area

is cleaned thoroughly.

• Wear a dust respirator mask or a dual lter

(dust and fume) respirator mask which has been

approved by the Occupational Safety and Health

Administration (OSHA), the National Institute of

Safety and Health (NIOSH), or the United States

Bureau of Mines. These masks and replaceable

lters are readily available at major hardware stores.

Product specificaties

Merk:	Milwaukee
Categorie:	Hittepistool
Model:	M18 2688-21

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee M18 2688-21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Hittepistool Milwaukee

Milwaukee 8988-20 Handleiding

9 Augustus 2023

Milwaukee 2688-20 Handleiding

15 Maart 2023

Milwaukee M18 2688-21 Handleiding

20 Februari 2023

Handleiding Hittepistool

Nieuwste handleidingen voor Hittepistool

Bavaria BHA 2000 Handleiding

5 December 2024

Einhell BT-HA 1500 Handleiding

4 December 2024

Ozito HGN-2100U Handleiding

1 December 2024

Bavaria By Einhell BHP 1500-2 Handleiding

19 November 2024

Bavaria By Einhell Bavaria BHP 2000 Handleiding

19 November 2024

Alpha Tools HLG 2000 Handleiding

17 November 2024

MSW HPF 2000 Handleiding

16 Oktober 2024

Hazet 9040T-1 Handleiding

17 Juni 2024

Rapid R2200-E Handleiding

10 April 2024

Rapid R2000 Handleiding

10 April 2024