Mikrotik Cube Lite60 Handleiding

Mikrotik Access point Cube Lite60

Lees hieronder de 📖 handleiding in het Nederlandse voor Mikrotik Cube Lite60 (7 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

Cube Lite60

Cube Lite60Cube Lite60

The Cube Lite60 is an outdoor wireless router with a built-in directional antenna that works in the 60 GHz spectrum.

This device needs to be upgraded to RouterOS v6.46 or the latest version to ensure compliance with local

authority regulations.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

Quickstart

Open the Ethernet door to connect an Ethernet cable to the Ethernet port, connect the other end of the Ethernet cable to the included PoE injector;

Plug the PoE injector into your network switch or computer;

Plug the included power supply into the PoE injector to start up the device;

Set LAN computer IP configuration to automatic (DHCP);

The default IP address of the unit is 192.168.88.1, open this address in your web browser to start the configuration;

User name: a and there is no password by default you will be logged in automatically to the Quick Set screen;

dmin

We recommend clicking the "Check for updates" button on the right side and updating your RouterOS software to the latest version to ensure the

best performance and stability;

To personalize your wireless network, SSID can be changed in the fields "Network Name";

Choose your country on the left side of the screen in the field "Country", to apply country regulation settings;

Set up your wireless network password in the field "WiFi Password" the password must be at least eight symbols;

Set up your router password in the bottom field "Password" to the right and repeat it in the field "Confirm Password", it will be used to login next

time;

Click on the "Apply Configuration" to save changes.

If device RX blocking condition has happened device will restore its signal after a few seconds.

MikroTik mobile app

Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Note. The information contained here is subject to change. Please visit the product page on for the most up to date version of www.mikrotik.com

this document.

Scan QR code and choose your preferred OS.

Install and open application.

By default, the IP address and user name will be already entered.

Click Connect to establish a connection to your device through a wireless network.

Choose Quick setup and application will guide you through all basic configuration settings in a couple of easy steps.

An advanced menu is available to fully configure all necessary settings.

Configuration

Once logged in, we recommend clicking the "Check for updates" button in the QuickSet menu, as updating your RouterOS software to the latest version

ensures the best performance and stability. For wireless models, please make sure you have selected the country where the device will be used, to

conform with local regulations.

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to

the possibilities: . In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address https://mt.lv/help https://mt.lv/winbox

of the device from the LAN side (all access is blocked from the Internet port by default).

For recovery purposes, it is possible to boot the device from the network (see ).Reset button

If the device loses connection, wait for few seconds and then the device will recover connection automatically.

Assembly and mounting

The device can be mounted on the vertical or horizontal pole as shown in picture A and B. Please note that a device needs to be mounted with bottom

latch facing down. The maximum pole diameter is 51 mm.

Choose your desired position, the device will require precise adjustment for best performance.

Attach provided mount to the back of the device with provided screws using a ph0 screwdriver.

Mount on pole with U bolt bracket using 8 mm ratchet.

Place a bolt in one of the three positions, they will allow for fine adjustment, when placed in the middle you can adjust in 23-degree range if an

adjustment needs to go further replace the screw in a different position.

Mounting and configuration of this device should be done by a certified person.

Alternatively, the device can be mounted on one of the three mounting slots on the backside of the device.

You can use a metal ring for example.

Use a Phillips screwdriver to loosen the metal ring.

Slide one end of it through the most convenient of the three mounting slots.

Position the device on the pole where it will be mounted.

Slide the loose end of the mounting ring back to its closing latch and use the screwdriver to tighten it.

The IP rating scale for this device is IP54. When mounting outdoors, please ensure that any cable openings are directed downwards. We

recommend using the POE injector and proper grounding with Cat6 shielded cable. When using and installing this device please pay attention

to Maximum Permissible Exposure (MPE) safety distance with a minimum of 20 cm between the radiator and your body.

Product specificaties

Merk:	Mikrotik
Categorie:	Access point
Model:	Cube Lite60
Kleur van het product:	Wit
Breedte:	130 mm
Diepte:	130 mm
Hoogte:	132 mm
Plaatsing:	Paal
Montage gereedschap:	Ja
Frequentie van processor:	650 MHz
Processormodel:	Qualcomm Atheros QCA9531
Inclusief besturingssysteem:	RouterOS
Frequentieband:	60 GHz
Aantal Ethernet LAN (RJ-45)-poorten:	1
Certificering:	CE/RED, FCC, IC, EAC
Intern geheugen:	64 MB
Duurzaamheidscertificaten:	RoHS
Type processor:	Ja
Ethernet LAN, data-overdrachtsnelheden:	10,100 Mbit/s
Soort antenne:	Intern
Flash memory:	16 MB
Maximale overdrachtssnelheid van gegevens:	- Mbit/s
2,4 GHz:	Ja
5 GHz:	Ja
Power over Ethernet (PoE):	Ja
Stroomverbruik (typisch):	5 W
Bedrijfstemperatuur (T-T):	-30 - 70 °C
Aantal producten inbegrepen:	1 stuk(s)