Mikrotik cAP ac Handleiding

Mikrotik Access point cAP ac

Lees hieronder de 📖 handleiding in het Nederlandse voor Mikrotik cAP ac (4 pagina's) in de categorie Access point. Deze handleiding was nuttig voor 85 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

cAP ac series

The cAP is a ceiling mountable wireless access point. It is already configured, you can simply plug in your ISP

cable and start using wireless Internet. We recommend you to set up a password to secure your device.

As with any MikroTik wireless access point, you can also manage it using the CAPsMAN wireless access point

management server. In this case, all configuration will be done in CAPsMAN. See Buttons and jumpers on how to

set this device as a managed CAP.

Powering

The device only accepts powering from the first ethernet port with PoE, so you must either use the included passive

PoE injector, or make sure your switch supports passive or 802.3af/at PoE output. The power consumption under

maximum load can reach 13W.

Setup

1. Connect your Internet cable to the first port.

2. Set your computer IP configuration to automatic (DHCP).

3. From your computer, connect to the wireless network name which starts with “MikroTik”.

4. Once connected to the wireless network, open http:// 192.168.88.1 in your web browser to start

configuration since there is no password by default, you will be logged in automatically. Set up your ,

password in the screen that loads. Please also specify your country, to comply with local regulations.

Configuration

By default, the device is configured as a wireless access point, with the first ethernet port (Eth1) configured as a

DHCP client, and the second interface bridged together with the wireless interface. A DHCP server is configured on

the bridge interface.

RouterOS includes many configuration options in addition to what is described in this document. We suggest to

start here to get yourself accustomed to the possibilities: . http://mt.lv/help

In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC http://mt.lv/winbox

address of the device from the LAN side (all access is blocked from the internet port by default).

For recovery purposes, it is possible boot the device from network, see section Buttons and jumpers.

Extension slots and ports

Two ethernet ports that support automatic cross/straight cable correction (Auto MDI/X), so you can use

either straight or cross-over cables for connecting to other network devices. The Eth2 port is capable of

powering another RouterBOARD device with passive PoE (up to 57 V). The maximum output current is

500mA when using less than 30V to power this device and 400mA when using more than 30V.

Integrated wireless module which supports AP/CPE/P2P/repeater modes.

See www.mikrotik.com support@mikrotik.com for more information or contact Document #34673. Modified on 13-Apr-18

Buttons and jumpers

Reset button

Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS

configuration (total 5 seconds).

Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now

look for a CAPsMAN server (total 10 seconds).

Or Keep holding the button for 5 more seconds until until LED turns off, then release it to make the

RouterBOARD look for Netinstall servers (total 15 seconds).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed

before power is applied to the device. Useful for RouterBOOT debugging and recovery.

Mode button

There are two mode buttons on this unit, but they both are performing the same action. The action of the mode

buttons can be configured from RouterOS software to execute any user supplied RouterOS script. You can also

disable this button. By default, the buttons will enable “dark mode”, which disables beeps and LED lights.

LED indicators

There are eight LED lights on the unit, which can be controlled in RouterOS software, or disabled altogether.

•Power LED indicates that the unit is receiving power in the ETH1 port.

•LTE LED incidates that the device is currently connected to a cellular tower.

•LTE Signal LEDs display the strength of the cellular signal.

•PoE LED indicates that the ETH2 port is currently powering another device with PoE.

Operating system support

The device supports RouterOS software with the version number at or above what is indicated in the RouterOS

menu . Other operating systems have not been tested. /system resource

See www.mikrotik.com support@mikrotik.com for more information or contact Document #34673. Modified on 13-Apr-18

Federal Communication Commission Interference Statement

FCC ID: TV7CPGI5ACD2ND

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.This device and its antenna must not be co-located or operation in

conjunction with any other antenna or transmitter.

IMPORTANT: Exposure to Radio Frequency Radiation. 13 cm minimum distance has to be maintained between the

antenna and user. Under such configuration, the FCC radiation exposure limits set forth for an

population/uncontrolled environment can be satisfied.

Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in

the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of

any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47

part 15.204. The installer should configure the output power level of antennas, according to country regulations and

per antenna type. Professional installation is required of equipment with connectors to ensure compliance with

health and safety issues.

Industry Canada

IC: 7442A-CPGI5ACD2ND

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

See www.mikrotik.com support@mikrotik.com for more information or contact Document #34673. Modified on 13-Apr-18

Product specificaties

Merk:	Mikrotik
Categorie:	Access point
Model:	cAP ac
Kleur van het product:	Wit
Breedte verpakking:	145 mm
Diepte verpakking:	145 mm
Hoogte verpakking:	30 mm
Plaatsing:	Muur
Frequentie van processor:	716 MHz
Processormodel:	Qualcomm Atheros IPQ4018
Aantal processorkernen:	4
Wi-Fi-standaarden:	802.11a,Wi-Fi 5 (802.11ac),802.11b,802.11g,Wi-Fi 4 (802.11n)
Inclusief besturingssysteem:	RouterOS
USB-poort:	Nee
Ethernet LAN:	Ja
Type stroombron:	AC
Inclusief AC-adapter:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	2
Vermogensverbruik (max):	13 W
Intern geheugen:	128 MB
Type processor:	Ja
SIM-kaartsleuf:	Nee
3G/4G USB modem compatibiliteit:	Nee
Geheugenkaart slot(s):	Nee
Wifi-band:	Dual-band (2.4 GHz / 5 GHz)
Wifi-standaard:	Wi-Fi 4 (802.11n)
WLAN gegevensoverdrachtsnelheid (max):	54 Mbit/s
Interfacetype Ethernet LAN:	Gigabit Ethernet
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Netwerkstandaard:	IEEE 802.3af,IEEE 802.3at
Soort antenne:	Intern
Antenne versterkingsniveau (max):	2.5 dBi
3G:	Nee
4G:	Nee
Intern:	Nee
Ethernet WAN:	Nee
Flash memory:	16 MB
Maximale overdrachtssnelheid van gegevens:	54 Mbit/s
2,4 GHz:	Ja
5 GHz:	Ja
Power over Ethernet (PoE):	Ja
DSL WAN:	Nee
AC-ingangsspanning:	17 - 57 V
Stroomverbruik (typisch):	13 W
Bedrijfstemperatuur (T-T):	-40 - 50 °C
Antenne-ontwerp:	Intern