McIntosh LB200 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor McIntosh LB200 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
McINTOSH LB200 OPERATION GUIDE
Connection Diagram and Light Box Operation
PC IN
PC OUT
ON
OFF/REMOTE
DC IN 5V
Use Only The
Power Adapter Provided
SERIAL
NUMBER
LB200 LIGHT BOX
McINTOSH LABORATORY, INC., BINGHAMTON, NY
HANDCRAFTED IN USA WITH US AND IMPORTED PARTS
PC IN (Power Control/Trigger) receives turn-
on signals from a McIntosh component and PC
OUT (Power Control/Trigger) sends turn-on
signals on to another McIntosh Component
Connect the supplied
AC/DC Power Adapter
DC Output Connnector
The AC/DC Power Adapter supplied
with the LB200 McIntosh Light Box
Connect to a live AC outlet (always
On) using the supplied AC Power Cord.
Refer to information on the power
supply to determine the correct voltage
Connect to the DC IN
5V connector on the
Rear Panel of the LB200
McIntosh Light Box
Integrated Amplifier or Preamplifier
Connect to another
McIntosh Component
Power Control or
Trigger Input Jack
Power On
Place the ON-OFF/REMOTE Power Control Switch in the ON
position or, if the PC IN Jack is connected to the Power Control/
Trigger Jack from a McIntosh Component, place the switch in the
OFF/REMOTE position.
Power Off
Place the ON-OFF/REMOTE Power Control Switch in the OFF/
REMOTE position or, if the PC IN Jack is connected to the
Power Control/Trigger Jack from a McIntosh Component, switch
power Off on the connected McIntosh Component.
2
Copyright © 2022 by McIntosh Laboratory, Inc. McIntosh Part Number 24118102
McINTOSH LB200 OPERATION GUIDE
Using LB200 for Device Consolidation
The McIntosh LB200 Light Box enables you to place devices (such as a cable box or streaming box) inside of it to help declutter your entertainment setup
without losing the ability to send signals to those devices using your remote control(s). Perform the following steps to take advantage of this functionality.
Rear View
Top View
1. Remove the screws on the top (circled in dots in Top
View photo) and the screws from the upper edge of the
rear (circled in dots in Rear View photo). Carefully lift
and remove top cover.
2. Hold your hand on the inside of the Light Box up
against the back plate in the rear. This will support the
back plate and prevent it from falling as you remove
the screws on the outside. Remove the screws (circled
in solid white in Rear View photo) and carefully
remove back plate to reveal an opening in the rear of
the Light Box.
3. Place your desired devices inside the Light Box
and funnel their respective wiring through the opening
of rear of the Light Box. You can use the additional
holes in the rear to zip tie your wires together.
4. Inside the Light Box is a Xantech XT-DL-IRK
DinkyLinkâ„¢ IR Receiver Kit (circled in white in
the Inside View photo). Follow the IR Receiver Kit's
included Installation Instructions to connect your
devices to the IR Receiver Kit.
Inside View
Front View
5. When all devices are connected correctly, replace
the top cover and secure it in place with the four top
screws (circled in dots in Top View and Rear View
photos).The devices inside the Light Box will now
receive signals from their respective remote controls
from the sensor on the front of the Light Box (circled
in white in the Front View photo).


Product specificaties

Merk: McIntosh
Categorie: Niet gecategoriseerd
Model: LB200

Heb je hulp nodig?

Als je hulp nodig hebt met McIntosh LB200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd McIntosh

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd