Makita HG5012K Handleiding

Makita Hittepistool HG5012K

Lees hieronder de 📖 handleiding in het Nederlandse voor Makita HG5012K (7 pagina's) in de categorie Hittepistool. Deze handleiding was nuttig voor 88 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

MAKITA - Titel Seite 1 Montag 24. Juni 2009

I II

I 1

HG5012

HG551V

HG651C

English - 6 -

WARNING: Non-observance of the safety

rules while working with the hot air tool

can lead to fire, explosion, electric shock or

burns. Read the operating instructions before using

the tool and always observe the safety rules. Save

these instructions and give them to persons that have

not been instructed before they use the tool.

WARNING: A damaged casing or an ope-

ned unit can lead to a hazardous electric

shock. Do not open the unit and do not put

a damaged unit into operation. Do not drill into the

casing, e.g., to attach a company label. Before any

work on the unit, pull the mains plug.

WARNING: A damaged power cord can

lead to a hazardous electric shock. Check

the power cord regularly. Do not operate

the unit when the power cord is damaged. Always

have a damaged cord replaced through a specialist.

Do not wrap the cord around the unit and protect it

from oil, heat and sharp edges. Do not carry the unit

by the cord and do not use the cord to pull the plug

from the outlet.

WARNING: Do not work in rain or in a

moist or wet environment. This can lead to

a hazardous electric shock. Keep the unit

dry. Store the unit in a dry location when not in use.

Consider the weather conditions. Do not work in wet

sanitary facilities. Avoid body contact with groun-

ded cables or surfaces, such as pipes, radiators,

ranges and refrigerators.

WARNING: Connect power tools that are

used in the open via a residual current cir-

cuit breaker (RCCB).

WARNING: Danger of explosion! The hot air

tool can explosively ignite combustible fluids

and gases. Do not work in a potentially

explosive environment. Check the surrounding

before starting to work. Do not work on fuels or gas

containers or in their vicinity, even when they are

empty.

WARNING: Danger of fire! Heat can reach

combustible materials that are hidden behind

coverings, in ceilings, floors or cavities, and

ignite them. Inspect the work area before starting to

work and in case of doubt, abstain from using the

hot air tool. Do not point the unit at the same spot for

extended periods.

WARNING: Danger of fire! An unsupervised

operating hot air tool can set fire to objects

that are close by. The unit must be supervised

at all times during operation. When allowing the

switched off unit to cool down, always place it down

vertical and standing. Allow the unit to cool down

completely.

WARNING: Danger of fire! When working

plastics, varnish or similar materials, gases

develop that are easily inflammable and can

lead to explosions. Be prepared for flames to deve-

lop and keep suitable fire-extinguishing means at

hand.

WARNING: Danger of intoxication! When

working plastics, varnish or similar materials,

gases develop that can be aggressive or

toxic. Avoid breathing in vapours, even when they

appear to be harmless. Always provide for good

ventilation of the work area or wear a respirator.

WARNING: Danger of injury! The hot air jet

can injure persons or animals. Touching the

hot tube of the heating element or the nozzle

leads to skin burns. Keep children and other persons

away from the unit. Do not touch the tube of the hea-

ting element or the nozzle when they are hot. Do not

use the unit as a hair dryer; it develops much more

heat than a hair dryer. Do not use the unit to heat up

fluids or to dry objects or materials that are

destroyed through the influence of hot air.

WARNING: Unintentional starting or unex-

pected switching on of the heating element

after actuation of the thermal relay can lead

to injuries. Make sure that the switch is set to OFF

when connecting the unit to the mains supply. Switch

the unit OFF when the thermal relay has actuated.

WARNING: Danger of injury! Using an air-

flow reflection nozzle that is not suitable for

your unit can lead to burns. Use only original

accessories for your model that are listed in these

operating instructions.

WARNING: Danger of injury and fire! The

hot air tool is dangerous for children. Keep

the hot air tool out of the reach of children

DANGER: Danger of overheating! Incorrect

handling can lead to an accumulation of heat

and thus damage the unit. Do not operate the

unit when it is placed down horizontally or when

pointed downward. The air-intake opening and the

nozzle must not be covered. Use only nozzles that

are suitable for your unit.

Recycle raw materials instead of disposing

as waste. The unit, accessories and packag-

ing should be sorted for environmentally-

friendly recycling.

WELDY.book Seite 6 Mittwoch, 17. Mai 2006 1:02 13

English - 7 -

IMPORTANT SAFETY INSTRUCTIONS

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this

plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

READ THESE INSTRUCTIONS

Warning: Extreme care should be taken when stripping paint. The peelings, residue and vapors of paint may con-

tain lead, which is poisonous. Any pre-1977 paint may contain lead and paint applied to homes prior

to 1950 is likely to contain lead. Once deposited on surfaces, hand to mouth contact can result in the

ingestion of lead. Exposure to even low levels of lead can cause irreversible brain and nervous system

damage; young and unborn children are particularly vulnerable.

Before beginning any paint removal process you should determine whether the paint you are removing

contains lead. This can be done by your local health department or by a professional who uses a paint

analyzer to check the lead content of the paint to be removed. LEAD-BASED PAINT SHOULD ONLY BE

REMOVED BY A PROFESSIONAL AND SHOULD NOT BE REMOVED USING A HEAT GUN.

Persons removing paint should follow these guidelines:

1. Move the work piece outdoors. If this is not possible, keep the work area well ventilated. Open the windows and

put an exhaust fan in one of them. Be sure the fan is moving the air from inside to outside.

2. Remove or cover any carpets, rugs, furniture, clothing, cooking utensils and air ducts.

3. Place drop cloths in the work area to catch any paint chips or peelings. Wear protective clothing such as extra

work shirts, overalls and hats.

4. Work in one room at a time. Furnishings should be removed or placed in the center of the room and covered.

Work areas should be sealed off from the rest of the dwelling by sealing doorways with drop cloths.

5. Children, pregnant or potentially pregnant women and nursing mothers should not be present in the work area

until the work is done and all clean up is complete.

6. Wear dust respirator mask or a dual filter (dust and fume) respirator mask which has been approved by the*Occupational Safety and Health Administration (OSHA), the National Institute of Safety and Health (NIOSH),

or the United States Bureau of Mines. These masks and replaceable filters are readily available at major hard-

ware stores. Be sure the mask fits. Beards and facial hair may keep masks from sealing properly. Change filters

often. DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.

7. Use caution when operating the heat gun. Keep the heat gun moving as excessive heat will generate fumes which

can be inhaled by the operator.

8. Keep food and drink out of the work area. Wash hands, arms and face and rinse mouth before eating or drink-

ing. Do not smoke or chew gum or tobacco in the work area.

9. Clean up all removed paint and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any

other surface where paint or dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high phosphate

detergent or trisodium phosphate (TSP) to wash and mop areas.

10.At the end of each work session put the paint chips and debris in a double plastic bag, close it with tape or twist

ties and dispose of properly.

11.Remove protective clothing and work shoes in the work area to avoid carrying dust into the rest to the dwelling.

Wash work clothes separately. Wipe shoes off with a wet rag that is then washed with the work clothes. Wash

hair and body thoroughly with soap and water.

* Applicable for cUL listed products only.

SAVE THESE INSTRUCTIONS

WELDY.book Seite 7 Mittwoch, 17. Mai 2006 1:02 13

Product specificaties

Merk:	Makita
Categorie:	Hittepistool
Model:	HG5012K
Kleur van het product:	Black, Blue
Gewicht:	580 g
Breedte:	80 mm
Diepte:	230 mm
Hoogte:	240 mm
Stroombron:	AC
Instelbare temperatuur:	Ja
Input vermogen:	1600 W
Minimum luchtstroom:	300 l/min
Maximum luchtstroom:	500 l/min
Beschermingsklasse:	II
Bedrijfstemperatuur (max):	500 °C
Bedrijfstemperatuur (min):	350 °C