Lowrance Mark 4X DSI Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Lowrance Mark 4X DSI (44 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 231 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/44
Traditional Sonar and DSI Sonar Installation
This document covers the installation of the transducer and display unit installation, which includes con-
necting the unit to power and installing the unit on the bracket mount.
The rst section of the document covers the installation of a traditional sonar skimmer transducer. DSI
sonar installation is covered in the last section of the manual.
Make sure you read all the installation instructions before drilling holes in your vessel!
Traditional Sonar Transducer Installation
One piece bracket (Recommended Tools and Supplies — not included)
Drill Marine grade above-or-below waterline sealant
1” (25mm) or 5/8 (15mm) drill bit Marine grade epoxy (Shoot-thru-hull install only)
#29 (0.136”) (3mm) drill bit Zip ties (trolling motor mount)
Phillips (Slotted-head) screwdriver TMB-S bracket kit (Skimmer trolling motor mount)
NOTE
:
This majority of this installation does not apply to the GPS only units since they do
not have a transducer. Turn to pages 8-11 for information on mounting the display unit and
connecting the unit to power.
0.TWEETY INSTALL_SONAR_DSI.indd 1 9/14/2011 11:55:30 PM
2
Traditional Sonar
A. Select a transducer location
To function properly the Skimmer transducer must
be in the water at all times and in a location that has
a smooth ow of water when the boat is moving.
If the transducer is not placed in a smooth ow
of water, interference caused by bubbles and
turbulence may show on-screen as random lines or
dots. The unit also could lose bottom signal when
the boat is on plane.
B. Aligning Ratchets on bracket
You will use the ratchets to ensure the trans-
ducer is installed parallel to the ground.
1. Insert the ratchets in the bracket with the
letter “A” aligned with the dot stamped
on the outside of the transducer bracket.
2. Slide the transducer into the bracket
and temporarily slide the bolt through
the transducer bracket.
Good locations
Poor locations
Ratchet Bracket
NOTE: Mount the transducer at least
one foot away from the engine lower
unit.
Too high
Poor angle
0.TWEETY INSTALL_SONAR_DSI.indd 2 9/14/2011 11:55:30 PM


Product specificaties

Merk: Lowrance
Categorie: Niet gecategoriseerd
Model: Mark 4X DSI

Heb je hulp nodig?

Als je hulp nodig hebt met Lowrance Mark 4X DSI stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Lowrance

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

MSW

MSW -BPS1 Handleiding

5 November 2024
MSW

MSW -C&A HP 100 Handleiding

5 November 2024
Physa

Physa PHY-SK-2 Handleiding

5 November 2024
Physa

Physa PHY_SM_02 Handleiding

5 November 2024
Physa

Physa -RR-09 Handleiding

5 November 2024
Physa

Physa PHY-EB-1 Handleiding

5 November 2024
Physa

Physa -RR-11 Handleiding

5 November 2024
Physa

Physa -RR-15 Handleiding

5 November 2024
Physa

Physa -RR-12 Handleiding

5 November 2024
Physa

Physa -RR-08 Handleiding

5 November 2024