Lowrance EP-25 Speed Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Lowrance EP-25 Speed (8 pagina's) in de categorie Marine. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
1
Pub. 988-0154-451
EP-25 Speed
Electronic Sensor
Installation Instructions
This instruction sheet tells how to install your EP-25 Speed sensor and
connect it to a NMEA 2000 network using LowranceNET network
components. You must refer to your digital gauge, sonar or GPS unit's
manual for sensor operation instructions.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. You should decide where to
install all components before drilling any holes in your vessel.
Some sonar or GPS units may require a software upgrade to display
NMEA 2000 data correctly and a manual addendum describing how to
operate the sensor. You can download these free and get additional
information on the NMEA 2000 compatible LowranceNET system at
our web site, www.lowrance.com.
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending. See our web site for the latest
product status information.
The EP-25 Speed sensor.
The EP-25 consists of the paddle wheel module, a blue female locking
cable connector and the smart module. The cable length from the
Paddle wheel module
Smart module
Blue female NMEA
2000 connector
2
connector to the smart module is 18 inches (46 cm) and from the smart
module to the paddle wheel module is 10 feet (3 meters).
The smart module converts speed data from the paddle wheel to the
NMEA 2000 data format. This allows any digital gauge, sonar or GPS
unit connected to the NMEA 2000 network to display the speed.
The EP-25 Speed, like the other Lowrance Electronic Probe (EP)
sensors, is designed only for use with a NMEA 2000 Network. It must
be connected to a NMEA 2000 network or it will not function.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If you are connecting to an
existing LowranceNET network, those are all the electronic
components you need. If this is the first sensor you are connecting, you
will also need a one-time purchase of a LowranceNET Node Kit.
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2 foot (61
cm) extension cable, T connector, 120-ohm male terminator and 120-
ohm female terminator.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one refer to the "Setup and Installation of NEMA
2000 Networks, General Information" document (part number 988-
0154-172) included with your EP-25 sensor. If that document is missing
it can be downloaded free from the Lowrance web site.
Supplies are not included, unless otherwise indicated. Required supplies
for this job are: four #8 stainless steel wood screws (3/4" or 19 mm long),
high quality, marine grade above- or below-waterline sealant compound.
Recommended tools for this job include: screwdriver, drill, 1/8" (3 mm) drill
bit for pilot holes. If you want to feed the smart module or blue cable
connector through a transom or bulkhead, you will also need a 7/8" (22
mm) drill bit.
3
Installation
To install the speed sensor, first find a location on the boat's transom
where the water flow is smoothest. Don't mount the paddle wheel
module behind strakes or ribs. These will disturb the water flow to the
paddle wheel.
Make sure the paddle wheel will remain in the water when the boat is
on plane. Also make sure the location doesn't interfere with the boat's
trailer. Typically, the paddle wheel module is mounted about one foot
(30.5 cm) to the side of the transom's centerline.
Stern view showing good mounting location on transom.
Once you've determined the proper location for the paddle wheel, place
it on the transom. The bottom of the bracket should be flush with the
hull's bottom. Using the paddle wheel's bracket as a template, mark the
hull for the screws' pilot holes. Drill four 1/8" (3 mm) holes, one in each
end of the slots.
Paddle wheel module rear view.
Mount the paddle wheel module to the hull using four #8 stainless steel
wood screws. Use a high quality, marine grade above- or below-
waterline sealant to seal the screws. Make sure the paddle wheel
bracket is flush with the bottom of the hull and tighten the screws.
good location
Rear view
Bottom of hull
Product specificaties
| Merk: | Lowrance |
| Categorie: | Marine |
| Model: | EP-25 Speed |
Heb je hulp nodig?
Als je hulp nodig hebt met Lowrance EP-25 Speed stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Marine Lowrance
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
30 April 2023
Handleiding Marine
- Marine Garmin
- Marine Kenwood
- Marine AdvanSea
- Marine Alphatron
- Marine BandG
- Marine Dickinson Marine
- Marine Digital Yacht
- Marine Eagle
- Marine Easy
- Marine Echotec
- Marine Efoy
- Marine Fastnet
- Marine Furuno
- Marine Fusion
- Marine Geonav
- Marine Humminbird
- Marine Icom
- Marine Interphase
- Marine IVT
- Marine Katadyn
- Marine Klarfit
- Marine KVH
- Marine Lofrans
- Marine Lorenz
- Marine Nasa
- Marine Navico
- Marine Navionics
- Marine Navman
- Marine Nordwest-funk
- Marine Plastimo
- Marine Polmar
- Marine President
- Marine Raymarine
- Marine Raytheon
- Marine Rockford Fosgate
- Marine Sailtron
- Marine SEAFARER
- Marine Silva
- Marine Simrad
- Marine Standard Horizon
- Marine WEST SYSTEM
Nieuwste handleidingen voor Marine
16 Oktober 2023
16 Oktober 2023
16 Oktober 2023
12 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
2 Oktober 2023
21 September 2023
21 September 2023