Lindell Audio LiN2A Handleiding

Lindell Audio Compressor LiN2A

Lees hieronder de 📖 handleiding in het Nederlandse voor Lindell Audio LiN2A (2 pagina's) in de categorie Compressor. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

of this document may be reproduced in any form without explicit written consent from Lindell Audio. Lindell Audio is

a RAD Global Distribution company.

LiN2A

Vintage Leveling Amplier

Specications

Attack Dictated by T4BLA optocell

Release Dictated by T4BLA optocell

Ratio Program-dependant

Gain Up to 40 DB ±1DB

Voltage 115VAC, 230VAC rear panel switchable AC Mains Input: IEC320-C14 standard plug.

AC Mains Input 100V-240V depending on supplied

Dimensions Width 438mm (19”)

Height 88mm (2U)

Depth 250mm

1. Read these instructions.

2. Keep these instructions

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus that produce heat.

9. Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they

exit from the apparatus. If the power cord

becomes frayed, stop using immediately.

10. Use only attachments/accessories specied

by the manufacturer

11. Use only with a cart, stand, tripod, bracket

or table specied by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms

or when unused for long periods of time.

13. Refer all servicing to qualied service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as power supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

14. This apparatus shall not be exposed to

dripping or splashing, and no object lled with

liquids, such as vases, shall be placed on the

apparatus.

15. Note that this apparatus is not completely

disconnected from the AC mains service when

the power switch is in the OFF position.

16. The mains plug or power inlet on the product

is used as the disconnect device, so the

disconnected device shall remain readily

operable when reconnected.

17. Any changes or modications not expressly

approved in this manual could void your

authority to operate this apparatus.

Important !

Be sure to only use the supplied 3-prong

IEC cable provided with this unit.

The triangular lightning ash icon is in-

tended to alert the user to the presence

of uninsulated, dangerous voltage within

Quick Start Guide

1. Mute your studio monitors.

2. Connect your LiN2A to your mixing bus or

patch bay then using balanced TRS cables.

3. Set all controls fullly counter-clockwise.

4. Set the switch to ON, and apply power. Power

Power LED meter will light up.

5. Unmute your monitors, and verify that signal

is passing to and from the unit.

6. Set the and controls to Gain Peak Reduction

about 12 o’clock, and set the to Meter mode

Gain Reduction. Increase the Input until the

meter is deecting a few dB.

7. Once again verify signal is passing through the

unit. If so, the unit is functioning correctly.

Basic Use

Use the control to set the desired Peak Reduction

amount of compression. Higher Peak Reduction

settings will result in a quieter signal; use the Gain

control to compensate for this loss. Try to match

the original level as closely as possible for A/B

comparisons that aren’t colored by differences in

overall volume.

Compression Modes

• Compress: A gentler compression setting of

roughly 3:1. Note that in the ‘2A compression

style, compression is variable depending on

the dynamic range of the program material.

Higher Peak Reduction values result in slight-

ly higher compression ratios.

• Limit: A hard limiter with a ∞:1 ratio.

What about Attack/Release?

Part of the allure of ‘2A-style compression is its

ease of use, thanks in no small part to its hard-

wired attack and release settings. Expect it to

sound great with no fuss.

Attack time is incredibly fast at around 10 milli-

seconds. About 1/40th the time it takes to blink.

Release time is dependent opon the amount of

compression applied by the conPeak Reduction -

trol, and can range anywhere from half a second

to ve seconds for total release.

Meter Calibration

Making sure that the meter returns to zero is im-

portant to the Lin2A’s functionality. This is con-

trolled the the master calibration set screw on the

back of the unit.

To calibrate, set the to Gain Metering Mode

Reduction and ensure that no audio is passing

through the unit. Then, using a athead

screwdriver, rotate the screw on the rear panel

until the needle rests on 0.

Voila! Meter calibrated.

The T4BLA Optocell

The LiN2A features a custom-designed Black Lion

Audio T4BLA Optocell. It yields sublime transpar-

ency and smooth gain reduction due to highly

selective trimming of its photocell.

1. Power Button: turns the Lin 2A

on/off.

2. Mode: Sets Lin2A to Limit or

Compress mode.

3. Gain: Sets the post-compression

make-up gain to compensate for

level lost during compression

4. VU Meter: Displays units select-

ed by Meter Mode.

5. Peak Reduction: Sets the de-

sired amount of compression/

limiting.

6. Meter Mode: Sets the type of

information rendered on the

meter. Gain Reduction meters

the amount of gain reduction ap-

plied. and Output +10 Output

+4 will render the Output level

as respectively described.

7. : ONLY use the AC Power Input

supplied IEC Cable to power this

unit.

8. Voltage setting: Select the volt-

age suitable to your region. Do

not power the Lin-2A by inap-

propriate voltage.

9. Grounding plug: The unit

should only be used in a prop-

erly-grounded studio. Do not de-

feat the third-pin ground for use

in an ungrounded studio.

10. Meter Calibration: Use this con-

trol to adjust the 0 resting point

when no compression is being

applied.

11. TRS Output: Balanced line-level

output.

12. TRS Input: Balanced line-level

input.

Note: For proper

performance, balanced

TRS must be used for all

inputs and outputs.

Important Safety Instructions

the product’s enclosure that may be of

sufcient magnitude to constitute a risk of

electric shock.

The triangular exclamation point icon is

intended to alert the user to the presence

of important operating and maintenance

(servicing) instructions in the literature ac-

companying the product.

The Lindell Audio LiN2A complies with all

applicable RoHS / WEEE European Union

directives.

Do not attempt to service this unit yourself,

as it will void your warranty. Please check

your unit carefully upon receipt and return

to place of purchase immediately if there

are any problems with the product. After

that, the standard Lindell Audio 1 YEAR

warranty will apply to defects in materials

and workmanship.

International Service

For service or warranty assistance, please

contact the Lindell Audio distributor in your

country through the dealer from whom you

purchased this product.

Limited One-Year Warranty

Lindell Audio’s LiN2A is warranted by Lin-

dell Audio to be free from defects in ma-

terials and workmanship for the period of

ONE (1) YEAR to the original purchaser. In

the event of such defects, the product will

be repaired without charge or, at our op-

tion, replaced with a new one if delivered to

Lindell Audio prepaid, together with a copy

of the sales slip or other proof of purchase

date. The warranty excludes problems due

to normal wear, abuse, shipping damage

or failure to use the product in accordance

with the specications.

All parts and labor are covered under this

Limited Warranty. However, if it is deter-

mined by Lindell Audio that the device was

damaged or made defective through abuse,

we reserve the right to charge the customer

for the cost of the repair.

Lindell Audio shall not be liable for damag-

es based upon inconvenience, loss of use

of the product, loss of time, interrupted

operation or commercial loss or any other

damages, whether incidental, consequen-

tial or otherwise. This warranty gives you

specic legal rights, and you may have oth-

er rights, which will vary from state to state.

This warranty is not transferable.

2 3 4 5 6

Product specificaties

Merk:	Lindell Audio
Categorie:	Compressor
Model:	LiN2A

Heb je hulp nodig?

Als je hulp nodig hebt met Lindell Audio LiN2A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Compressor Lindell Audio

Lindell Audio LiN2A Handleiding

2 Juni 2023

Handleiding Compressor

Nieuwste handleidingen voor Compressor

Total TACLI2002 Handleiding

16 December 2024

Bavaria BAC 200/200F Handleiding

5 December 2024

Einhell YPL 206 Handleiding

4 December 2024

Einhell BT-AC 160/6 OF Handleiding

4 December 2024

Einhell TE-AC 400/100/10 D Handleiding

4 December 2024

Einhell TE-AC 300/50/10 Handleiding

4 December 2024

Einhell BT-AC 190/10 Handleiding

4 December 2024

Einhell BT-AC 140/24 OF Handleiding

4 December 2024

Einhell BT-AC 190/24 Handleiding

4 December 2024

Einhell EURO 4300 V Handleiding

4 December 2024