LevelOne FEU-0511 Handleiding

LevelOne Niet gecategoriseerd FEU-0511

Lees hieronder de 📖 handleiding in het Nederlandse voor LevelOne FEU-0511 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Brief introduction





Many thanks for purchasing Fast Ethernet Switch! This

product supports IEEE802.3U/100Base- / protocol, as Tx Fx

well as full duplex and half duplex mode. It provides 4 TX

ports and a UPLINK port, which can suit for most 10/100M

networks. This manual is for 100M convert s. Ter he

following purchasing guide is for your reference.

Purchasing guide for optical media converters

Model

Specications

4 x UTP- MM

10/100M adaptive,

multi mode up to 2km, ST/SC/FC

4 x UTP- SM

10/100M adaptive,

single mode up to 100km, ST/ /FC SC



Packing list

Please check the following items in the package before

installing the converter.

Fast Ethernet Switch 1 piece

AC/DC adapter 1 piece

User manual 1 copy

Please contact the dealer immediately for any missing or

damaged items.



 Interface

RJ-45 interface

The transmission media CAT5 twisted-pair with is a

maximum length of 100 meters. It features auto -negotiation

of straight through line and crossover cables.

Fiber interface

The or ST ber interface is of duplex type, namely TX SC

and RX. When the two sets of optical converter are

interfaced or connected to switch with ber interface, the

ber is in cross connection, namely "TX-RX", "RX-TX"

(direct butting for single optical fiber).

2. nnection Co

Connect the network device (work station, hub or switch) to

the -45 jack of the optical converter through twisted-pair RJ

CAT5. Connect the multi-mode/single mode ber to SC/ST

ber interface of the optical converter. Turn the power on.

The corresponding LED is on for correct connection. (See a

the table below for the LED indicator lamp)

Fig.1 Basic Network Connection

Panel

1. Front

2. Back



Explanation for LED indicator lamp

The LED indicator lamps serve as device monitoring and

error display. The following explains each LED indicator.

LED

Status

Explanation

P WR

Green

Lit when Power is available.

L/A

Green

Lit when there is/are network device(s)

connect the corresponding port(s)

Blink

Blink when the corresponding ports

is(are) transmitting data ows



Installation

1. Turn off the power of the device/station in the network in

which the converter will be installed.

2. Ensure that there is no activity in the network.

3. Attach ber cable from the converter to the ber network.

The ber connections must be matched-transmit socket to

receive socket.

4. Attach a UTP cable from the 100Base-TX network to the

RJ-45 port on the converter.

5. Connect the power cord to the converter.

6. Turn on the power of th converter and check that the e

Power LED lights up. The TP Link and FX Link LED will

light when all the cable connections are satisfactory.

7. When the P1~P5 LINK/ACT LED is green, the

corresponding port is running under 10/100Mbps; the

ber port is forced running under 100Mbps.



Technical parameter s:

1. Standard Protocol:

IEEE 802.3 10 Base-T

IEEE 802.3u 100Base-TX

IEEE 802.3u 100Base- FX

IEEE 802.3x ow control

2. Connectors:

4 UTP RJ-45 connector with PSE function ×

1 SC/ST connector ×

3. Operation mode:

FX: 100 Base-FX Full -duplex mode

TX: 10/100 Mbps auto-negotiation mode

4. Power supply:

5V@1A power adaptor

5. Operation temperature -10 ~60 : ℃ ℃

6. Storage temperature -40 5 : ℃~8 ℃

7. Operation humidity: 5%-90% non-condense

8. Storage humidity: 5%-90% non-condense

9. Twisted Pa cable: C 5 UTP cable ir at

10. Fiber cable:

multi-mode: 50/125, 62.5/125 m μ

single mode: 8.3/125, 9/125 or 10/125 m μ

11. Dimensions: 30 2 96 x W x ×11 ×mm (H D)



Warning:

1. This product is suitable for indoor application.

2. Place the dust cover on the ber interface when not in use.

3. It is dangerous to stare at the ber transmitter with the

naked eye.

4. The appliance inlet is used as the disconnect device and

shall remain readily operable at all time.



Trouble shooting:

1. Device is not connecting. Please check that the

corresponding network device is using the same transfer rate

as the media converter (10Mbps or 100Mbps).

2. If power loss is excessive in the ber, please check and

clean the ber patch cord connectors.

FEU-0511

5-Port Fast Ethernet Switch, 1 Port SC

User Manual

Please read before using the Switch

V1. 0_20150916

Product specificaties

Merk:	LevelOne
Categorie:	Niet gecategoriseerd
Model:	FEU-0511
Kleur van het product:	Black, Grey
Gewicht:	380 g
Breedte:	96 mm
Diepte:	112 mm
Hoogte:	30 mm
Gewicht verpakking:	540 g
Breedte verpakking:	140 mm
Diepte verpakking:	250 mm
Hoogte verpakking:	55 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Activity, Link, Power
Snelstartgids:	Ja
Inclusief AC-adapter:	Ja
Land van herkomst:	Taiwan
Vermogensverbruik (max):	6 W
Certificering:	FCC Class B, CE
Plug and play:	Ja
Netwerkstandaard:	IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Temperatuur bij opslag:	-20 - 90 °C
Rack-montage:	Nee
Output current:	2.5 A
Spanning:	5 V
Maximale overdrachtssnelheid van gegevens:	200 Mbit/s
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Nee
Stapelbaar:	Nee
Switchingcapaciteit:	- Gbit/s
MAC-adrestabel:	1024 entries
10G support:	Nee
Aantal basis-switching RJ-45 Ethernet-poorten:	4
Netstekker:	DC-in ingang
Type basis-switching RJ-45 Ethernet-poorten:	Fast Ethernet (10/100)
Full duplex:	Ja
Koperen ethernetbekabelingstechnologie:	10BASE-T, 100BASE-FX, 100BASE-TX
Rubberen voetjes:	Ja
Buffergrootte:	384 KB
Auto-negotiation:	Ja
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Code geharmoniseerd systeem (HS):	85176990
Store-and-forward:	Ja
Ondersteundende kabel types:	Cat5
Vezel-optische connector:	SC, ST
Fibre channel-poorten:	1
Fiber ethernet cabling technologie:	100BASE-FX
Packet forwarding rate (10 Mbps):	14880 pps
Packet forwarding rate (100 Mbps):	148800 pps
Transmissie afstand (max):	2 km
Fiber type:	Multimode