Lenmar R2G802U Handleiding

Lenmar Batterij-oplader R2G802U

Lees hieronder de 📖 handleiding in het Nederlandse voor Lenmar R2G802U (2 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 75 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

R2G802U

PLEASE READ THE INFORMATION AND FOLLOW ALL INSTRUCTIONS THOROUGHLY BEFORE

USING THIS PRODUCT.

Introduction

Thank you for purchasing the R2G802 2 Hour Charger. Read the instruction manual

thoroughly before use and keep the manual for later reference. It contains important

operating instructions for your R2G Rechargeable Battery System. The R2G802 is a

combination of Travel Alarm Clock, 2 hour microprocessor controlled charger for 1 to 4

AA/AAA NiMH batteries, Thermometer, and USB PowerPort for charging your cell

phones, MP3 players or any other device that accepts power from a USB port. All the

functions are displayed clearly on a large backlit LCD Display. The charger can be

powered 3 ways and includes a high efficiency “switching” type power supply will adjust

automatically to any voltage from 100 – 240VAC, for international use. A car-cord for

using the charger in the car and a USB cable for powering the charger from your

computer are also included.

Before Use

To activate the clock and thermometer functions, pull out the tab from the side of the

casing at the access cover to the clock battery on the bottom of the unit. The clock

portion of the LCD display will turn on and you will hear alarm music for 10 seconds. The

Clock / Alarm is now ready for use and should be set to the proper time / date. If the LCD

display get dim or the sound of the alarm tone become weak, replace the clock battery

with another new “CR-2025” type 3V Lithium battery which is located on the bottom side

of the charger base.

Caution:

Batteries are partially charged as shipped. Must be charged prior to first use for full

capacity.

Charge NiMH type batteries on this charger.only

Do Not mix AA and AAA or different capacity batteries together when charging

Use only R2G, NoMEM PRO or other proper NiMH compatible charger to recharge

the batteries included.

Batteries may leak or explode causing personal injury if inserted improperly, disposed

of in fire, mixed with other battery types, or short circuited.

•

LCD Display Legend

Getting Ready

Choose the adapter plate for the type of battery you will be charging. Each of the adapter

plates is labeled as to the batteries it can work with. If the charger base does not already

have the adapter plate you want attached, you will need to remove the adapter plate first

by pushing down on the plate and sliding it to the rear of the charger base (away from

the LED indicators). Then, attach the selected adapter plate to the charger unit by

aligning the arrows on the sides of the adapter plates and the charger base as shown.

While pressing down lightly on the adapter plate, slide the plate toward the front of the

charger base until it locks.

Charging Instructions

1. Choose the source of power for the charger unit. You can use the AC adapter which

is international capable accepting 100-240VAC (plug adapter may be required in other

countries, not included), the DC car cord while on the move or plugged into a USB port

on your computer (charge times are increased when USB power is used). Simply plug

the desired power cable into the side of the charger unit and the other end into the

appropriate power source.

2. Insert 1 to 4 pieces of AA or AAA rechargeable Ni-MH batteries into any open battery

location observing the proper battery polarity to the marks in the battery compartment.

Do not mix AA and AAA batteries while charging. The Blue backlight will light up for

around 10 sec once the batteries inserted correctly. For charging AAA batteries, pull

down the adjustable battery contact plate before inserting the AAA batteries into the

compartment. The charger automatically adjusts the charging current depending on the

size of the battery being charged.

3. The LCD will indicate the proper charging and the word “Charge” will be shown to the

left of the battery symbols that indicate each battery’s charge progress. After the

batteries are fully charged, the wording “FULL” will indicate on the LCD screen to

indicate the trickle charge and the charged batteries are ready for use. Once charge is

complete, remove batteries and unplug the charger as soon as it is practical. Do not

leave batteries in charger for extended periods of time (more than 1-2 days) or when the

charger is not plugged in. Unplug the charger when not in use.

4. Begin again at Step-1 to charge the next set of batteries.

Bad Cell Detection

When charge process is started, the charger detects the health status of each of the cells in

the battery compartment. If any batteries are unsuitable for charging, i.e. short circuit or

reversed polarity, the word “BAD” will indicate on the LCD screen and ”battery” icon will flash.

USB Charge Port Operation

When using the USB PowerPort on this charger, the AA/AAA charger function has priority.

The USB PowerPort will not be available while batteries are installed and charging. Once the

AA/AAA batteries have completed their charge, the USB port will be turned on automatically.

The “USB symbol” will be shown on the LCD screen to indicate the USB socket is

ready for use.

Note: Make sure the maximum loading is not exceeding 500mA for the USB socket. Do not

attempt to overload the USB port or damage to the charger or USB device may result.

Clock / Alarm / Day-Date operation

The following shows which buttons on the setting panel you need to press to navigate

between modes. The 2 feet on the bottom rear of the chassis act as switches to activate the

blue backlight on the LCD display. In any mode, just to hit the top of the unit lightly and the

black light will light on for about 10 seconds. The backlight will only operate while the unit is

plugged into power using any of the supplied power adapters.

In the regular Time mode, press the button once and the “Time” icon will starts to flash on

the LCD screen along with the item to be changed, which indicates Time Setting mode. Use

and buttons to change the value of the flashing item. Once the flashing item is set to

what you want, press to select the next setting and change as listed above. The “Year”

can be set in the range of 2000 to 2099. The day of the week is calculated automatically

according with the date you set. Once all the items are set, press the button to exit the

setting mode (set mode will automatically if there is no input for 1 minute). The following figure

shows the order of items during the setting process.

12/24 Hour Mode:

In the regular Time mode, pressing the button will toggle between 12-hour and

24-hour mode.

1. 2. 3.

Fig. 1

Fig. 2

Fig. 3

Setting the Time and Date

Setting the Alarm

In the regular Time mode, press the button to enter the Alarm mode. The “ALARM”

icon will appear on the LCD in this mode. Pressing the button will start the Alarm icon

flashing along with the item to be set. Use the and buttons to change the item to

the setting you want. When you are done setting each item, press the button to move

to the next item. You can set the hour and minute you want the alarm to sound, the length

of time delay for the “Snooze” setting and select the alarm tone to sound. The following

figure shows the order of items during the Alarm setting process. The “SNOOZE” can be

set in the range of 1 to 60 minutes and there are 8 different kinds of alarm tones for your

choice. Press and to change the setting you want. Pressing the button will exit

the setting mode (set mode will automatically if there is no input for 1 minute). The

following figure shows the order of items during the Alarm setting process.

Turning on /off Alarm and Snooze Mode

From the regular Time mode, press the button to enter the Alarm mode. Once in the

Alarm Mode; use the button to cycle through the 3 Alarm modes shown below

depending on the alarm function wanted.

When an alarm is turned on, the alarm tone sounds for about 1 minute when the alarm

time is reached. If “SNOOZE” mode is turned on, the alarm tone will sounds 2 times for

about 1 minute when the snooze is reached. You can stop the alarm sound by pressing

the button.

Alarm mode – The alarm will sound for about 1 minute. While the alarm is sounding it

can be silenced by pressing the button.

Alarm/Snooze mode – the alarm will sound for about 1 minute. If the alarm is not

silenced early by pressing the button or if the button is pressed while the alarm

is sounding, the alarm goes into Snooze mode and will sound again after the time

entered in the Snooze setting has elapsed.

Thermometer

This charger uses a temperature senor to measure temperature. Temperature is

displayed in units of 0.1˚C (or 0.1˚F) and displayed in the range from 0 ˚C to 50˚C (32˚F

to 99˚F). In the regular Time mode, you can toggle between ˚C or ˚F by pressing the

button.

Limited 3 Year Warranty

This limited warranty starts from the date of original purchase and expires three years

thereafter. If, during this period, any part, because of manufacturing defects or workman-

ship, fails to function properly under normal use it will be repaired at no charge for parts

and labor or, at our option, the product will be replaced. The following is excluded:

damages from delay or loss of use of equipment or damaged batteries, malfunctions

resulting from misuse, tampering, unauthorized repairs, modifications or accident.

Package the unit and its accessories carefully using ample padding material to prevent

damage in transit and ship it prepaid and insured to:

LENMAR ENTERPRISES, INC.

4035 Via Pescador USA

Camarillo, CA 93012

When sending in product for service, your package should include evidence of date and

place of purchase. Enclose $10.00 for shipping and handling for addresses in the U.S.

and $15.00 in Canada. For outside the U.S. and Canada, freight will vary depending

upon ship-to address.

Proposition 65 Notice (California)

The following statement is required in the state of California pursuant to the settlement

of an action brought by the Mateel Environmental Justice Foundation against multiple

electronics and appliance manufacturers

WARNING: Handling the cord on this product will expose you to lead, a chemical

known to the state of California to cause birth defects or other reproductive harm.

Wash hands after handling.

For additional questions, comments or to explore other Lenmar battery solutions, visit

our web site at: www.poweredbylenmar.com or call 800/424-2703

Warning:

Before charging, read instructions

This charger is intended for use with Nickel-metal-hydride rechargeable batteries only.

Attempting to charge other types of batteries may cause personal injury and damage

to the charger.

Do not expose charger to rain or moisture. For indoor use only.

Disconnect from power when not in use.

Never use any cable or power adapter not recommended by manufacturer. Otherwise,

risk of fire, electric shock or injury to persons may result.

Do not operate the charger if it has been subjected to shock or damage. Take it to a

qualified serviceman for repair.

Do not disassemble the charger. Incorrect reassembly may result in a risk of electric

shock or fire.

Unplug the charger from outlet before attempting any maintenance or cleaning.

This AC power unit supplied is intended to be used in a vertical or floor

mount position only.

•

4. 5. 6.

Caution:

Batteries are partially charged as shipped. Must be charged prior to first use for full

•

compartment. The charger automatically adjusts the charging current depending on the

size of the battery being charged.

according with the date you set. Once all the items are set, press the button to exit the

setting mode (set mode will automatically if there is no input for 1 minute). The following figure

shows the order of items during the setting process.

Charge Times:

Size / Type

AAA

Charging Current

1200mA for charging

1-2 pcs batteries

or 800mA for charging

3-4 pcs batteries

600mA

Charging time

(For 1-2 pcs)

90 minutes

100 minutes

110 minutes

120 minutes

130 minutes

140 minutes

70 minutes

80 minutes

90 minutes

100 minutes

110 minutes

120 minutes

NiMH

1800mAh

2000mAh

2200mAh

2400mAh

2600mAh

2800mAh

700mAh

800mAh

900mAh

1000mAh

1100mAh

1200mAh

Charging time

(For 3-4 pcs)

135 minutes

150 minutes

165 minutes

180 minutes

195 minutes

210 minutes

*Charge time will vary depending upon the brand, capacity and condition of batteries being charged.

Size / Type

AAA

Charging Current

560mA for charging

1-2 pcs batteries

or 280mA for charging

3-4 pcs batteries

600mA

Charging time

(For 1-2 pcs)

180 minutes

200 minutes

220 minutes

240 minutes

260 minutes

280 minutes

70 minutes

80 minutes

90 minutes

100 minutes

110 minutes

120 minutes

NiMH

1800mAh

2000mAh

2200mAh

2400mAh

2600mAh

2800mAh

700mAh

800mAh

900mAh

1000mAh

1100mAh

1200mAh

Charging time

(For 3-4 pcs)

270 minutes

300 minutes

330 minutes

360 minutes

390 minutes

420 minutes

140 minutes

160 minutes

180 minutes

200 minutes

220 minutes

240 minutes

Charger Input:

Charge rate :

AC or Car adapter (12VDC input)

Charge rate :

USB power adapter (5VDC input)

Trickle mode :

Power Supply:

USB Output:

Safety Features:

12VDC, 600mA

AA size – 1-2 pcs., 1.4VDC ea. cell, 1200mA

AA size – 3-4 pcs., 1.4VDC ea. cell, 800mA

AAA size – 1-4 pcs., 1.4VDC ea. cell, 600mA

AA / AAA size 1-2 pcs., 1.4VDC ea. cell, 560mA

AA / AAA size 3-4 pcs., 1.4VDC ea. cell, 280mA

AA 50mA ; AAA 25mA

• 100-240V AC, 50-60 Hz International

Compatible, (12VDC output)

• Car Cord adapter (12VDC output)

• USB cord adapter (5VDC output)

5VDC, 500mA max.

-deltaV, max. time, overcharge protection,

bad cell / reverse polarity / shorted cell detection.

C D

•

When using AC or Car adapter (12VDC input)

When using USB power adapter (5VDC input)

Product specificaties

Merk:	Lenmar
Categorie:	Batterij-oplader
Model:	R2G802U
Kleur van het product:	Zwart
Oplaadtijd:	120 min
Capaciteit van de accu/batterij:	2150 mAh
Accu/Batterij voltage:	1.2 V
Ondersteund aantal accu's/batterijen:	4
Frequentie:	50/60 Hz
Output current:	0.6 A
Gewicht verpakking (imperiaal):	0.95 lbs
Batterijen inbegrepen:	Ja
Chemische samenstelling:	NiMH