Kramer WP-2UT/R-KIT Handleiding

Kramer AV extender WP-2UT/R-KIT

Lees hieronder de 📖 handleiding in het Nederlandse voor Kramer WP-2UT/R-KIT (4 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
WP-2UT/R-KIT Quick Start
P/N:
2900- 301411QS
Rev:
1
Scan for full manual
Step 1: Check in the b what’s ox
WP-2UT USB Transmitter
1 C-USB/AB-6 cable
Installation accessories
1 Bracket set
PT-2UR USB Receiver
1 Power adapter and cord
Frame set and faceplate
1 Quick start guide
Step 2: Get to know your -2UT/R-KIT WP
WP-2UT
#
Feature
Function
1
USB 2.0 Type B Port
Connect to USB host.
2
LINK LED
Flashes blue when a link is established.
3
ON LED
Lights green when locally powered by the power adapter.
Lights orange when powered by PoC.
4
Ring Tongue Terminal Grounding Screw
Connect to grounding wire (optional).
5
SRV (Tx, Rx)
5-pin Terminal Block
Connector (with a
common G pin)
Connect for rmware upgrade.
6
RS-232 (G, Rx, Tx)
Connect for serial extension (9600 baud rate).
7
Power Supply 2-pin Terminal Block
Connector
Connect to the power supply. Connect GND to GND, + V to + 12 12V.
8
LINK POC OUT RJ-45 Connector â—„â–º
Connect to the LINK IN port on the PT-2UR and to power either the device
via the receiver or the receiver by the device.
PT-2UR
WP-2UT
#
Feature
Function
9
LINK LED
Flashes blue when a link is established.
10
AUDIO OUT 3.5mm Mini Jack
Connect to an unbalanced stereo audio acceptor.
11
USB 2 Type A Ports (1 to 4)
Connect to USB devices.
Connect directly to the power adapter in order to charge USB
PT-2UR
devices.
12
ON LED
Lights green when locally powered by the power adapter. Lights orange
when powered by PoC.
13
LINK IN RJ-45 Connector
Connect to the LINK OUT port on the WP-2UT and to power either the
device via the transmitter or the transmitter by the device.
14
PROG (Tx, Rx)
5-pin Terminal Block
Connector (with a
common G pin)
Connect for rmware upgrade.
15
RS-232 (G, Rx, Tx)
Connect for serial extension (9600 baud rate).
16
12V DC Power Connector
Connect to the supplied power adapter.
Step 3: Install the -2UT/R-KIT WP
WP-2UT
Insert the device into the in-wall box (note that rst you need to connect the HDBT cable and power) and connect the parts as
shown in the illustrations below:
US-D Version
DECORA® design or similar frames are
included in US-D models. DECORA® is a
registered trademark of Leviton
Manufacturing Co., Inc.
We recommend that you use any of the
following standard 1 Gang in-wall junction
boxes (or their equivalent):
• : 1 Gang US electrical US-D
junction boxes.
PT-2UR
Install PT-2UR using one of the following methods:
• Attach the rubber feet and place the unit on a at surface.
• Fasten a bracket (included) on each side of the unit and attach it to a at surface
(see www.kramerav.com/downloads/PT-2UT/R).
• Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/PT-2UT/R).
• Ensure that the environment (e.g., maximum ambient temperature &
air ow) is compatible for the device.
• Avoid uneven mechanical loading.
• Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
• Maximum mounting height for the device is 2 meters.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your WP-2UT/R-KIT. For best results, we recommend
that you always use Kramer high-performance cables to connect AV equipment to the WP-2UT/R-KIT.
In the following example, devices that are connected to the USB ports are powered/charged while connected. PT-2UR
Only 9600 baud rate is supported for RS-232 communication for both and . WP-2UT PT-2UR
Grounding the WP-2UT (Optional)
1. Connect the ring tongue terminal to the building grounding point wire (a green-yellow, AWG#18 (0.82mm2) wire,
crimped with a proper hand-tool is recommended).
2. Insert the M3x6 screw through the toothed lock washers and the tongue terminal in the order shown above.
3. Insert the M3x6 screw (with the two toothed lock washers and ring tongue terminal) into the grounding screw hole
and tighten the screw.


Product specificaties

Merk: Kramer
Categorie: AV extender
Model: WP-2UT/R-KIT

Heb je hulp nodig?

Als je hulp nodig hebt met Kramer WP-2UT/R-KIT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding AV extender Kramer

Kramer

Kramer TP-583Rxr Handleiding

25 November 2024
Kramer

Kramer KDS-17DEC Handleiding

25 November 2024
Kramer

Kramer TP-580TD Handleiding

25 November 2024
Kramer

Kramer TP-46N Handleiding

25 November 2024
Kramer

Kramer TP-126xl Handleiding

25 November 2024
Kramer

Kramer TP-125xl Handleiding

25 November 2024
Kramer

Kramer KW-14T Handleiding

25 November 2024
Kramer

Kramer KW-14R Handleiding

25 November 2024
Kramer

Kramer TP-574 Handleiding

25 November 2024
Kramer

Kramer TP-580RA Handleiding

25 November 2024

Handleiding AV extender

Nieuwste handleidingen voor AV extender