Kramer 676R Handleiding
Kramer
AV extender
676R
Lees hieronder de 📖 handleiding in het Nederlandse voor Kramer 676R (4 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
676T, 676R Quick Start
P/N:
2900- 301397QS
Rev:
4
Scan for full manual
676T / 676R Quick Start Guide
This guide helps you install and use your 676T / 676R for the rst time.
Go to www.kramerav.com/downloads/676T or www.kramerav.com/downloads/676R to download the latest
user manual and check if rmware upgrades are available.
Step 1: Check what’s in the b ox
676T HDMI Optical Transmitter or
676R HDMI Optical Receiver
1 Bracket set
4 Rubber feet
1 Power cord and adapter
1 Quick start guide
1 OSP-MM1 Fiber Optic SFP+ Transceiver
Step 2: Get to know your 676T and 676R
676T can be connected to a single 676R device or to multiple devices via optical splitters. When multiple devices are connected, a
receiver device is dened as primary when its Tx (SFP+ OUT) optical ber is connected directly to the 676T Rx optical fiber (SFP+ IN).
676T
#
Feature
Function
1
IN LED
Lights green when a connected source device (with an active HDMI signal) is detected. ™
Flashes 4 times green when resetting the device.
O when active signal is detected on the connected HDMI source device. no
2
OUT LED
Lights green when an HDMI acceptor device (with an active HDMI signal) detected. is
O when no active signal is detected on the connected acceptor.
3
LINK LEDs
Tx
Lights green when OUT IN SFP+ is connected, and an active Tx optical link is detected.
Lights red when OUT IN SFP+ is connected, and a fault is detected on the single/primary
676R receiving optical link.
O when the OUT IN SFP+ is disconnected.
Rx
Lights green when OUT IN SFP+ is connected, and an active optical link is detected. Rx
Lights red when OUT IN SFP+ is connected, and a fault is detected on the incoming optical
link.
O when OUT IN SFP+ is disconnected.
4
ON LED
Lights green when the device receives power.
5
HDMI™ IN Connector
Connect to an HDMI source.
6
RS- (Tx, Tr, G) 3-pin 232
Terminal Block Connector
Connect to a serial controller to communicate serial with all the connected receivers. ly
Receives -232 communication only from a single/primary receiver. RS
7
OUT IN SFP+ Connector
Connect the ber optic cable to the plugged- SFP+ optical module connectors. in
(OSP-MM1, included).
8
SETUP 4-way DIP-switch
Sets the device behavior.
9
RESET Recessed Button
Press and hold for 5 seconds or less to reset the device.
Press and hold for over 5 seconds to reset the device to factory default values.
10
SERVICE Micro USB Port
Connect to a PC to perform rmware upgrade (via K-Upload).
11
12V DC Power Connector
12V DC connector for powering the unit.
676R
#
Feature
Function
12
IN LED
Lights green when a connected HDMI source device (with an active HDMI signal) is
detected.
Flashes 4 times green when resetting the device.
O when no active signal is detected on the connected source device.
IN LED is always o for receivers other than the single/primary device.
676R
13
OUT LED
Lights green when an HDMI acceptor device (with an active HDMI signal) is
detected on the single/primary 676R device.
O when no active signal is detected on the connected acceptor.
14
LINK LEDs
Tx
Lights green when OUT IN SFP+ is connected, and an active Tx optical link is
detected.
Lights red when OUT IN SFP+ is connected, and a fault is detected on the 676T
receiving optical link.
LED on devices other than the single/primary Tx 676R device always light red.
O when OUT IN SFP+ is disconnected.
Rx
Lights green when OUT IN SFP+ is connected, and an active optical link is Rx
detected.
Lights red when OUT IN SFP+ is connected, and a fault is detected on the incoming
active optical link.
O when OUT IN SFP+ is disconnected.
15
ON LED
Lights green when the device receives power.
16
HDMI™ OUT Connector
Connect to an HDMI acceptor.
17
RS-232 (Tx, Tr, G) 3-pin Terminal
Block Connector
Connect to the serial control port of a controlled device located next to the 676R.
Only the controlled device connected to the single/primary receiver returns
serial data to the transmitter.
18
OUT IN SFP+ Connector
Connect the ber optic cable to the plugged-in SFP+ optical module connectors
(OSP-MM1, Included ).
19
SERVICE Micro USB Port
Connect to a PC to perform rmware upgrade via K-Upload.
20
12V DC Power Connector
12V DC connector for powering the unit.
Step 3: Mount /676R 676T
Install 676T/676R using one of the following methods:
• Attach the rubber feet and place the unit on a at surface.
• Fasten a bracket (included) on each side of the unit and attach it to a at surface
(see www.kramerav.com/downloads/676T).
• Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/676T).
• Ensure that the environment (e.g., maximum ambient temperature &
air ow) is compatible for the device.
• Avoid uneven mechanical loading.
• Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
• Maximum mounting height for the device is 2 meters.
Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your 676T/676R.
For optimal performance, use the recommended Kramer cables available at . www.kramerav.com/product/676T
Using third-party cables may cause damage!
To install/replace the OSP-MM1 or other Kramer recommended SFP+
transceiver:
1. Pull the bail out and remove the currently installed transceiver,
insert the protective cap and store in a safe place.
2. Make sure the bail of the new transceiver is pushed up, in the
closed position.
3. Insert the new transceiver into the relevant optical device SFP+ slot
and push it in until it clicks.
4. Remove the protective cap and store it in a safe place for future
use.
Warning: Connecting the OSP SFP+ connector to an LC(APC) ber
connector may cause poor performance and damage the connector!
Refer to www.kramerav.com/downloads/OSP-MM1 for more information.
Warning: Class 1 Laser Product
• Invisible laser radiation present.
• Avoid long-term viewing of laser.
• Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes, microscopes and
magnifying lenses, but not spectacles or contact lenses).
• Avoid placing optical devices in the emitted beam that could cause the concentration of the laser radiation to be
increased.
Step 5: Connect power
Connect the power cord to 676T/676R and plug it into the mains electricity.
Safety Instructions (See for updated safety information)www.kramerav.com
Caution:
• There are no operator serviceable parts inside the unit.
Warning:
• Use only the power cord that is supplied with the unit.
• Disconnect the power and unplug the unit from the wall before installing.
Product specificaties
| Merk: | Kramer |
| Categorie: | AV extender |
| Model: | 676R |
Heb je hulp nodig?
Als je hulp nodig hebt met Kramer 676R stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding AV extender Kramer
26 November 2024
26 November 2024
26 November 2024
26 November 2024
26 November 2024
26 November 2024
26 November 2024
25 November 2024
25 November 2024
25 November 2024
Handleiding AV extender
- AV extender Philips
- AV extender Abus
- AV extender Act
- AV extender Ag Neovo
- AV extender Allnet
- AV extender Audio Pro
- AV extender Belkin
- AV extender D-Link
- AV extender Digitus
- AV extender Dune
- AV extender Ebode
- AV extender Edimax
- AV extender Eminent
- AV extender Genexis
- AV extender Gigabyte
- AV extender Hama
- AV extender InFocus
- AV extender KEF
- AV extender Konig
- AV extender LevelOne
- AV extender Logilink
- AV extender Manhattan
- AV extender Marmitek
- AV extender Monacor
- AV extender Nedis
- AV extender Peerless
- AV extender Polycom
- AV extender Pyle
- AV extender Renkforce
- AV extender Roland
- AV extender Speaka
- AV extender Teufel
- AV extender Vivotek
- AV extender One For All
- AV extender Monoprice
- AV extender Schwaiger
- AV extender Steren
- AV extender Atlona
- AV extender Trevi
- AV extender Vivolink
- AV extender Techly
- AV extender SIIG
- AV extender Tripp Lite
- AV extender Approx
- AV extender Vision
- AV extender Matrox
- AV extender Gefen
- AV extender Planet
- AV extender Intellinet
- AV extender Lindy
- AV extender IOGEAR
- AV extender Black Box
- AV extender DataVideo
- AV extender Kindermann
- AV extender Bogen
- AV extender AJA
- AV extender Peerless-AV
- AV extender Marshall Electronics
- AV extender ATen
- AV extender Wentronic
- AV extender Dynaudio
- AV extender Adder
- AV extender Kopul
- AV extender Extron
- AV extender MIPRO
- AV extender AMX
- AV extender Crestron
- AV extender I3-Technologies
- AV extender StarTech.com
- AV extender PureLink
- AV extender UTEPO
- AV extender Aitech
- AV extender Advantech
- AV extender Smart-AVI
- AV extender Micro Connect
- AV extender KanexPro
- AV extender Intelix
- AV extender ASSMANN Electronic
- AV extender Blustream
- AV extender Avocent
- AV extender Rose
- AV extender Accell
- AV extender Ecler
- AV extender Rose Electronics
- AV extender Epcom
- AV extender CYP
- AV extender TV One
- AV extender SmartAVI
- AV extender IMG Stage Line
- AV extender Oehlbach
- AV extender AVMATRIX
- AV extender HELGI
- AV extender Liberty
- AV extender Enson
- AV extender Lightware
- AV extender Alfatron
- AV extender SWIT
- AV extender Hall Research
- AV extender WyreStorm
- AV extender Rocstor
- AV extender MuxLab
- AV extender Seco-Larm
- AV extender ConnectPro
- AV extender Kanex
- AV extender TechLogix Networx
- AV extender C2G
- AV extender SEADA
- AV extender Comprehensive
- AV extender Analog Way
- AV extender Sescom
- AV extender DVDO
- AV extender Camplex
Nieuwste handleidingen voor AV extender
20 Februari 2025
20 Februari 2025
7 Februari 2025
29 Januari 2025
13 Januari 2025
13 Januari 2025
13 Januari 2025
13 Januari 2025
13 Januari 2025
8 Januari 2025