Kramer 675R/T Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Kramer 675R/T (4 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
675R/T Quick Start
P/N:
2900- 301389QS
Rev:
1
Scan for full manual
Step 1: Check what’s in the box
675T HDMI Optical Transmitter
2 Power adapters and cords
1 Quick start guide
675R HDMI Optical Receiver
8 Rubber feet
2 Bracket sets
2 OSP-MM1 Fiber Optic SFP+ Transceivers
Step 2: Get to know your 675R/T
675T
#
Feature
Function
1
IN LED
Lights green when a connected source device (with an active HDMI signal) is
detected.
Flashes 4 times green when resetting the device.
O when a connected source device with an active signal is not detected.
2
OUT LED
Lights green when both a connected HDMI source (with an active HDMI signal) and
a connected far-end HDMI acceptor are detected.
O if either the source or the acceptor is not connected, or an active signal is not
present.
3
LINK Tx and Rx LEDs
Light green when OUT IN SFP+ is connected and an active optical link is detected.
Light red when OUT IN SFP+ is connected, an active optical link is not detected. but
O when OUT IN SFP+ is disconnected.
4
ON LED
Lights green when the device receives power.
5
HDMI™ IN Connector
Connect to an HDMI source.
6
OUT IN SFP+ Connector
Connect the ber optic cable to the plugged- SFP+ optical module connect . in or
7
RESET Recessed Button
Press and hold to reset settings to factory default values.
8
SERVICE Micro USB Port
Connect to a PC to perform rmware upgrade (via K-Upload).
9
12V DC Power Connector
12V DC connector for powering the unit.
675R
#
Feature
Function
10
IN LED
Lights green when a connected far-end source device (with an active HDMI signal)
is detected.
O when a connected source device with an active signal is not detected.
11
OUT LED
Lights green when both a connected HDMI source (with an active HDMI signal) and
a connected HDMI acceptor are detected.
O if either the source or the acceptor is not connected, or an active signal is not
present.
12
LINK Tx and Rx LEDs
Light green when OUT IN SFP+ is connected, and an active optical link is detected.
Light red when OUT IN SFP+ is connected but an active optical link is not detected.
O when OUT IN SFP+ is disconnected.
13
ON LED
Lights green when the device receives power.
14
HDMI OUT Connector
Connect to an HDMI acceptor.
15
OUT IN SFP+ Connector opening
Connect the ber optic cable to the plugged- SFP+ optical module connect . in or
16
SERVICE Micro USB Port
Connect to a PC to perform rmware upgrade (via K-Upload).
17
12V DC Power Connector
12V DC connector for powering the unit.
Step 3: Install 675R/T
Install 675R/T using one of the following methods:
Attach the rubber feet and place the unit on a at surface.
Fasten a bracket (included) on each side of the unit and attach it to a at surface
(see www.kramerav.com/downloads/675R/T).
Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/downloads/675R/T).
Ensure that the environment (e.g., maximum ambient temperature &
air ow) is compatible for the device.
Avoid uneven mechanical loading.
Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
Reliable earthing of rack-mounted equipment should be maintained.
Maximum mounting height for the device is 2 meters.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your 675R/T. For best results, p2-we recommend that you
always use Kramer high-performance cables to connect AV equipment to 675R/T.
Make sure that you always cross-connect the ber connections, Rx OUT to Tx IN and Rx IN to Tx OUT, as unidirectional optical
transmission is carried on simplex ber strands.
To install/replace the OSP-MM1 or other Kramer recommended SFP+
transceiver:
1. Pull the bail out and remove the currently installed transceiver,
insert the protective cap and store in a safe place.
2. Make sure the bail of the new transceiver is pushed up, in the
closed position.
3. Insert the new transceiver into the relevant optical device SFP+ slot
and push it in until it clicks.
4. Remove the protective cap and store it in a safe place for future
use.
Warning: Connecting the SFP+ transceiver to an LC(APC) ber
connector may cause poor performance and damage the connector!
Refer to www.kramerav.com/downloads/OSP-MM1 for more information.
Warning: Class 1 Laser Product
Invisible laser radiation present.
Avoid long-term viewing of laser.
Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes, microscopes and
magnifying lenses, but not spectacles or contact lenses).
Avoid placing optical devices in the emitted beam that could cause the concentration of the laser radiation to be
increased.
Step 5: Connect the power
Connect the power cords to 675T 675R and and plug into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information).
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the power cord that is supplied with the unit.
Disconnect the power and unplug the unit from the wall before installing.


Product specificaties

Merk: Kramer
Categorie: AV extender
Model: 675R/T

Heb je hulp nodig?

Als je hulp nodig hebt met Kramer 675R/T stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding AV extender Kramer

Kramer

Kramer TP-580RD Handleiding

26 November 2024
Kramer

Kramer 675R/T Handleiding

26 November 2024
Kramer

Kramer 676R Handleiding

26 November 2024
Kramer

Kramer PT-872xr Handleiding

26 November 2024
Kramer

Kramer 691 Handleiding

26 November 2024
Kramer

Kramer TP-580T Handleiding

25 November 2024
Kramer

Kramer 612R Handleiding

25 November 2024
Kramer

Kramer 617T Handleiding

25 November 2024

Handleiding AV extender

Nieuwste handleidingen voor AV extender