Kidde KI-PD Handleiding

Kidde Rookmelder KI-PD

Lees hieronder de 📖 handleiding in het Nederlandse voor Kidde KI-PD (4 pagina's) in de categorie Rookmelder. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Page 1 of 4 D A T A S H E E T K85001-0646

Not to be used f or installation purposes. Issue 1

KIDDE® Catalog Intelligent Initiating Devices

Technology that saves lives

Intelligent Smoke

Detector

KI-PD

Overview

The KI-PD optical smoke detector brings advanced sensing

technology to a practical design that increases efﬁciency, saves

installation time, cuts costs, and extends life safety and property

protection capabilities. Continuous self-diagnostics ensure reli-

ability over the long-haul, while environmental compensation helps

reduce maintenance costs.

Like all KI Series detectors, the KI-PD is an intelligent device that

gathers analog information from its optical sensor, converting this

data into digital signals. To make an alarm decision, the detector’s

on-board microprocessor measures and analyzes sensor read-

ings and compares this information to historical data. Digital ﬁlters

remove signal patterns that are not typical of ﬁres, thus virtually

eliminating unwanted alarms.

Standard Features

Note: Some features described here may not be supported by

all control systems. Check your control panel’s Installation and

Operation Guide for details.

• Next generation optical smoke sensing technology

• Wide 0.53 to 3.94 %/ft. (1.7 to 12.35 %/m) smoke obscuration

• Uses Existing Wiring

• Automatic Device Mapping

• Up To 250 Total Addresses Per Loop

• Two Levels of Environmental Compensation

• Two Levels of Dirty Detector Warning

• Twenty Pre-Alarm Settings

• Five Sensitivity Settings

• Non-Volatile Memory

• Electronic Addressing

• Identiﬁcation of Dirty or Defective Detectors

• Automatic Day/Night Sensitivity Adjustment

• Bicolor (Green/Red) Status Led

• Standard, Relay, Fault Isolator, and Audible Mounting Bases

• Sensor Markings Provide Easy Testing Identiﬁcation

S853

Compatible with VS & VM control systemsCompatible with VS & VM control systems

Page 2 of 4 D A T A S H E E T K85001-0646

Not to be used f or installation purposes. Issue 1

Application

The KI-PD detects extremely small particles of combustion and

triggers an alarm at the ﬁrst sign of smoke. Thanks to its high-

performance forward-scattering reﬂective response technology,

the photoelectric smoke sensor responds quickly and reliably to

a wide range of ﬁre types, espe cially slow burning ﬁres fuelled by

combustibles typically found in modern multi-use buildings.

Compatibility

The KI-PD detector is compatible with Kidde VS and VM series

panels.

Installation

Self-locking tab

LED Indicator

KI Series detector bases mount

to North American 1-gang boxes,

3-1/2 inch or 4 inch octagon

boxes, and to 4 inch square elec-

trical boxes 1-1/2 inches (38 mm)

deep. They mount to European

BESA and 1-gang boxes with 60.3

mm ﬁxing centers. See mounting

base installation and wiring for

more information.

Sensing and reporting technology

The microprocessor in each detector provides additional beneﬁts -

Self-diagnostics and History Log, Automatic Device Mapping, and

Fast, Stable Communication.

Self-diagnostics and History Log - Each KI Series detector

constantly runs self-checks to provide important maintenance in-

formation. The results of the self-check are automatically updated

and permanently stored in the detector’s non-volatile memory

Automatic Device Mapping - The loop controller learns where

each device’s serial number address is installed relative to other

devices on the circuit. The mapping feature provides supervision

of each device’s installed location to prevent a detector from being

reinstalled (after cleaning etc.) in a different location from where it

was originally.

Fast Stable Communication - On-board intelligence means less

information needs to be sent between the detector and the loop

controller. Other than regular supervisory polling response, the

detector only needs to communicate with the loop controller when

it has something new to report.

Testing & Maintenance

Each detector automatically identiﬁes when it is dirty or defective

and causes a “dirty detector” message. The detector’s sensitiv-

ity measurement can also be transmitted to the loop controller. A

sensitivity report may be printed to satisfy NFPA sensitivity mea-

surements, which must be conducted at the end of the ﬁrst year

and every two years thereafter.

The user-friendly maintenance program shows the current state

of each detector and other pertinent messages. Single detectors

may be turned off temporarily from the control panel. Availability of

maintenance features is dependent on the ﬁre alarm system used.

Accessories

Detector mounting bases have wiring terminals that are acces-

sible from the “room-side” after mounting the base to the electrical

box. The bases mount to North American 1-gang boxes and to

3½ inch or 4 inch octagon boxes, 1½ inches (38 mm) deep. They

also mount to European BESA and 1-gang boxes with 60.3 mm

ﬁxing centers. The KI-SB4, KI-RB4, and KI-IB4 mount to North

American 4 inch sq. electrical boxes in addition to the above

boxes. They include the GSA-TS4 Trim Skirt, which is used to

cover the “mounting ears” on the base. The KI-ABST mounts to a

4 inch square box only.

KI-IB

Isolator Base

GSA-LED

Remote LED

KI-RB

Relay Base

KI-SB

Standard Base

KI-ABST/T/LF

Audible Base

Remote LED GSA-LED - The remote LED connects to the KI-SB

or KI-SB4 Standard Base only. It features a North American size

1-gang plastic faceplate with a white ﬁnish and red alarm LED.

GSA-TS4 Trim Skirt - Supplied with 4 inch bases, it can also

be ordered separately to use with the other bases to help hide

surface imperfections not covered by the smaller bases.

Sounder Bases - KI Series sounder bases are designed for use

where localized or group alarm signaling is required.

• KI-ABST bases provide sounder capability to KI Series heat

and smoke detectors. They are not intended for use with

combination carbon monoxide detectors in Fire-plus-CO

mode.

• KI-ABDT bases provide sounder capability to KI Series

smoke and heat detectors, as well as carbon monoxide

detectors when used with a GSA-T3T4 Temporal Pattern

Generator.

• KI-ABLT bases provide 520 Hz low frequency sounder

capability to KI Series smoke and heat detectors, as well as

carbon monoxide detectors when used with a GSA-T3T4

Temporal Pattern Generator. The KI-ABLT is suitable for ap-

plications requiring low frequency audible tones.

Page 3 of 4 D A T A S H E E T K85001-0646

Not to be used f or installation purposes. Issue 1

Typical Wiring

The detector mounting bases accept #18 AWG (0.75mm2), #16

(1.0mm2), #14 AWG (1.5mm2), and #12 AWG (2.5mm²) wire sizes.

Sizes #16 AWG (1.0mm2) and #18 AWG (0.75mm2) are preferred

for ease of installation.

Standard Detector Base, KI-SB, KI-SB4

This is the basic mounting base

for Kidde KI Series detectors.

The GSA-LED Remote LED is

supported by this

Base.

Term Description

1 Not Used

2 DATA IN/OUT (+)

3 Not Used

4 DATA IN (-)

4 Remote LED (-)

5 Remote LED (+)

6 Not Used

7 DATA OUT (-)

Max resistance

per wire

must not exceed

10 Ohms

DATA IN (-)

DATA IN (+)

From Signature Controller

or Previous Device

DATA OUT (-)

DATA OUT (+)

To Next Device

Remote LED

Relay Detector Base, KI-RB, KI-RB4

This base includes a relay. Nor-

mally Open or Normally Closed

operation is selected during

installation. The dry contact is

rated for 1 amp (pilot duty) @

30 Vdc. The relay’s position is

supervised to avoid accidentally

jarring it out of position. The KI-RB

can be operated as a control

relay if programmed to do so at

the control panel. The relay base

does not support the GSA-LED

Remote LED. CONTACT RATING

1.0 Amp @ 30 VDC

(Pilot Duty)

Term Description

1 Normally Open

2 DATA IN/OUT (+)

3 Common

4 DATA IN (-)

5 Not Used

6 Normally-Closed

7 DATA OUT (-)

Isolator Detector Base, KI-IB, KI-IB4

This base includes a built-in line fault isolator for use on Class A

circuits. A detector must be installed for it to operate. The isolator

base does not support the GSA-LED Remote LED.

The isolator operates as follows:

- a short on the line causes all iso-

lators to open within 23 msec

- at 10 msec intervals,

beginning on one side

of the Class A

circuit nearest the loop

controller, the isolators

close to provide the

next isolator down the

line with power

- when the isolator next

to the short closes, it reopens within 10

msec.

The process repeats beginning on the

other side of the loop controller.

Term Description

1 Not Used

2 DATA IN/OUT (+)

3 DATA IN (-)

4 Not Used

5 Not Used

6 DATA OUT (-)

7 Not Used

Audible Sounder Bases, Fire Mode

AB4GT, AB4G, AB4G-LF sounder bases

KI-ABLT:

Output Mode

Default = Fire

Cut/remove jumper for

Fire plus CO

KI-ABST:

Tone Setting

Default = Temporal

Cut/remove jumper for

Steady

KI-ABDT:

Not Used

KI-ABDT,

KI-ABST,

KI-ABLT:

Volume Setting

Default = High

Cut/remove

jumper for

low dB

-24 Vdc out

To next base or EOL relay

Data out

to next KI Series device

24 Vdc in

From power supply

or previous base

Data in

From KI Device Controller

or previous device

DATA- DATA- DATA+

SIG+ SIG- OUT IN IN/OUT

Jumper cuts

Warnings & Cautions

• This detector does not operate without electrical power. As

ﬁres frequently cause power interruption, discuss further

safeguards with the local ﬁre protection specialist.

• This detector does not sense ﬁres in areas where smoke

cannot reach the detector. Smoke from ﬁres in walls, roofs,

or on the opposite side of closed doors may not reach the

detector.

• Photoelectric detectors have a wide range of ﬁre-sensing

capabilities and are best suited for detecting slow, smolder-

ing ﬁres.

• In Canada, install according to CAN/ULC-S524 Standard for

the Installation of Fire Alarm Systems, CSA C22.1 Canadian

Electrical Code, and the local authority having jurisdiction.

Product specificaties

Merk:	Kidde
Categorie:	Rookmelder
Model:	KI-PD
Kleur van het product:	Wit
Materiaal behuizing:	Kunststof
Stroombron:	AC
Type verpakking:	Doos
Ondersteuning voor plaatsing:	Horizontaal
Connectiviteitstechnologie:	Bedraad
Montagewijze:	Opbouwmontage
Aantal per verpakking:	1 stuk(s)
Aantal:	1
Temperatuur bij opslag:	-20 - 60 °C
Maximumbereik:	12.35 m
Draadloze verbindingen:	Ja
Beste gebruik:	Home,Office
Detector type:	Koolmonoxide detector
Koppelbaar:	Ja
Gemakkelijk te installeren:	Ja
Bedrijfstemperatuur (T-T):	0 - 49 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 93 procent