Kicker 50HDS962 Handleiding

Kicker Niet gecategoriseerd 50HDS962

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Kicker 50HDS962 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
1. Protect all painted surfaces and passing lamps, if equipped, with a soft cloth.
2. Remove seat and disconnect negative battery terminal. (Fig. 1)
a. On 2009 and later models it will help to remove the two T40 bolts and the ECM and tray. (Fig. 2)
3. Remove windshield and outer fairing.
a. Remove the three windshield fasteners. (Fig. 3)
b. Remove the four T27 fairing fasteners and disconnect the headlamp. (There are two as shown in and two located between theFig. 4
fork and the frame)
SPEAKER REMOVAL/ INSTALLATION
4. Unplug both terminals on the left and right speakers. (Fig. 5)
5. Remove the three T25 fasteners that secure eachspeaker to the inner fairing.
6. If using the KICKER grilles, peel the stock speaker grilles off of the speaker
stand-off (Fig. 6)
7. Separate the speaker from the stand-off, itā€™s a snap ļ¬t (Fig. 7)
8. Insert your KICKER speaker into the stand-off, making sure the terminals are
on the top side
9. Now is the time to install your KICKER emblems into the KICKER grilles, if
using
a. Place emblem into grille and bend tabs over
10. Lay the grille over the speaker and refasten the speaker to the inner fairing
using the hardware removed in step 2
AMP INSTALLATION
11. Disconnect the radio harness and antenna from the radio. (Fig. 8)
12. Remove the two T20 fasteners at the top of the radio chassis. (Fig. 8)
a. If using on a radio with CB and/or XM modules, remove the modules from the radio at this time.
13. Fasten the ampliļ¬er to the bracket using supplied hardware and orient with connector to the left side of the motorcycle. (Fig. 9)
14. Making sure all wiring is safely out of the way, slide the amp bracket over the radio chassis and engage tabs on amp bracket into the rubber
grommets on the radio. (Fig. 10)
15. Reinstall the T20 fasteners, removed in step 2, through the amp bracket and into the radio. (Fig. 10)
16. To reinstall modules, slide them under the radio chassis and fasten to the tabs on the ampliļ¬er bracket with supplied hardware. Note: At
this time it is recommended to refer to the section on the next page system setup then add the included mylar dip switch cover Fig. 15 WIRE
ROUTING
11. Take the electrical harness and plug it into the ampliļ¬ er.
12. Following the color code, route the left and right side speaker wires safely to their respective speakers. (Fig. 11 )-11a
13. Plug in the male ends into the stock harness, the terminals removed during speaker installation. (Fig. 11 )-11a
14. Plug the female ends onto the speaker terminals. (Fig. 11-11a)
15. Locate the headlamp harness and remove the red cap over the Orange/White wire.
a. If the wire is currently in use (e.g. accessory lighting) there is an additional connection on the KICKER harness to replace it.
16. Plug the blue wire from the KICKER harness into the Orange/White wire, making sure it is fully engaged. (Fig. 12)
17. Follow the proper procedure to remove the fuel tank.
18. Remove the electrical caddy lid.
19. Route the power harness on the left side of the frame neck, lay it into that caddy and under the seat. (Fig. 14)
a. You may want to remove the fuse now while ļ¬guring out wire placement.
50HDS962
Motorcycle Audio Kit Installation Guide for Harley DavidsonĀ® Electra
Glide | Street Glide | Ultra Glide | Bat Wing Trikes 1996ā€“2013 (FLHT)
Package Contents:
(1) Install Guide
(2) 5-1/4ā€ KICKER Speakers
(1) 300W KICKER Amp
(1) Wiring Harness
(6) 8-32 x 1/2ā€ Button Head Bolts
(6) 8-32 Nylock Nuts
(6) Black Cable Ties
(1) Amp Mounting Bracket
(4) Black Heat Shrink
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper
procedures and torque speciļ¬ cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit be may not
compatible with some aftermarket head units.
GETTING STARTED
(1) Mylar cover
(1) Dummy Plug
SYSTEM SETUP
KICKER recommends that the dip switches be set up as follows:
Input level - HI
HI-PASS ā€“ 80 Hz for front speakers
80 Hz for rear tour pack, 60 Hz for
6x9 baglids Input Gain control ā€“ 0
26. Connect the battery terminals, install fuse, check audio system operation and set gain to optimize system performance.
if you are not using rear speakers it is recommended to leave the amp 2 gain turned all the way down.
27. Be sure to check that none of the wires will be in a bind when the steering head is turned fully to the right or the left.
28. Disconnect negative battery terminal and carefully reassemble motorcycle.
29. Reconnect negative battery terminal, install seat and enjoy your KICKER audio system!
Note: If you have rear tour pack speakers using the KICKER HDTPH is connected to the connector in or bag lid speakers
Fig 14.
Note: If you are not using rear speakers you will need to connect the Dummy Plug (fig. 16) to the rear speaker connector
(fig. 14)
KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 46HDS962-A-20190827
1 2 3 4
5 6 7 8
10 11
12 13 14
9 11a
15 16

Product specificaties

Merk: Kicker
Categorie: Niet gecategoriseerd
Model: 50HDS962

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker 50HDS962 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Kicker

Kicker

Kicker 50HDS962 Handleiding

7 Mei 2024
Kicker

Kicker 50HDR154 Handleiding

7 Mei 2024
Kicker

Kicker 50HDS144 Handleiding

7 Mei 2024
Kicker

Kicker SF150SC15 Handleiding

6 Mei 2023
Kicker

Kicker KMLC Handleiding

4 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Xblitz

Xblitz R8 Power Charge Handleiding

3 December 2024
Xblitz

Xblitz R4 Power Handleiding

3 December 2024
Franke

Franke Urban UBG 610-78 Handleiding

3 December 2024
Franke

Franke ANX211RHD Handleiding

3 December 2024
Franke

Franke ANX220 Handleiding

3 December 2024
Dell

Dell NX3330 Handleiding

3 December 2024
Dell

Dell PowerConnect B-DCX-4s Handleiding

3 December 2024
Hager

Hager AKB83000701 Handleiding

3 December 2024
Hager

Hager AKB81500402 Handleiding

3 December 2024
Hager

Hager AKBA1500401V Handleiding

3 December 2024