Kicker 50HDR154 Handleiding

Kicker Niet gecategoriseerd 50HDR154

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker 50HDR154 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
1.
Remove the seat and disconnect both positive and negative battery terminals.
2.
Remove the windshield and outer fairing.
a.
Once the windshield screws are removed, gently pull off the top vent/cowl piece. There are two plastic retainer clips that hold it on.
b.
Remove your stock speaker grilles. Push them out from the inside of the fairing. They are fastened with a plastic retainer clip. Fig 1.
Fig 1.
Fig 1.
Fig 1.Fig 1.
c.
Unplug the turn signals. Fig 2.
Fig 2.
Fig 2.
Fig 2.Fig 2.
d.
Remove the lower T25 fasteners holding the air defl ectors to the inner fairing. Fig 3.
Fig 3.
Fig 3.
Fig 3.Fig 3.
e.
Remove the 3/16” allen bolts holding the turn signals to the inner fairing. Fig 4.
Fig 4.
Fig 4.
Fig 4.Fig 4.
f.
While holding the fairing, carefully remove the two T30 bolts behind the speaker grilles to remove the outer fairing and set aside. Fig
Fig
Fig
FigFig
5.
5.
5.
5.5.
3.
Remove the fuel tank.
a.
Remove the console.
b.
Unplug the fuel fi tting on the left side of the tank.
c.
Remove all four T40 mounting bolts and carefully lift the tank off the bike and set aside.
4.
Remove wiring caddy cover.
a.
Carefully release each tab along the caddy until it lifts completely. Fig 6.
Fig 6.
Fig 6.
Fig 6.Fig 6.
SPEAKER INST
SPEAKER INST
SPEAKER INST
SPEAKER INSTSPEAKER INSTALLA
ALLA
ALLA
ALLAALLATION
TION
TION
TIONTION
5.
Remove your stock speakers and replace them with your new PSC652 speakers in the kit.
a.
Install the speaker into the pod and fasten with the original speaker screws. Fig
Fig
Fig
Fig Fig .
.
.
..
7
7
7
77
50HDR154
Motorcycle Audio Kit Installation Guide for
Harley Davidson® Road Glide (FLTR) 2015–Newer
Package Contents:
Package Contents:
Package Contents:
Package Contents:Package Contents:
(1)
Install Guide
(2)
PSC652 KICKER Speakers
(1)
Wiring Harness
(2)
8-32 x 1/2” Button Head Bolts
(1) KICKER Amp KPX3004 (2) 8-32 Nylock Nuts
(6) Black Cable Ties
(1) Amplifier Mounting Bracket
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper
procedures and torque specifi cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit
may not
may not
may not
may notmay not
be compatible with some aftermarket head units.
PROGRAMMING HD RADIO
PROGRAMMING HD RADIO
PROGRAMMING HD RADIO
PROGRAMMING HD RADIOPROGRAMMING HD RADIO
NOTE:
NOTE:
NOTE:
NOTE:NOTE: It is necessary to re-flash your HD radio before installation of this kit.
GETTING ST
GETTING ST
GETTING ST
GETTING STGETTING STARTED
ARTED
ARTED
ARTEDARTED
HARNESS INST
HARNESS INST
HARNESS INST
HARNESS INSTHARNESS INSTALLA
ALLA
ALLA
ALLAALLATION
TION
TION
TIONTION
6.
Route speaker wires to their respective connectors. Fig. 2
Fig. 2
Fig. 2
Fig. 2Fig. 2
a.
Separate the speaker connectors and plug in the amplifier harness to each speaker. Fig. 8 & Fig. 8a
Fig. 8 & Fig. 8a
Fig. 8 & Fig. 8a
Fig. 8 & Fig. 8aFig. 8 & Fig. 8a
7.
Plug the switched power harness into the 2-pin amp connector on the throttle side. see also, Fig. 2 for location)
Fig. 9 (
Fig. 9 (
Fig. 9 (
Fig. 9 (Fig. 9 (
8.
Plug the blue wire on the kicker harness into the switched power harness lead with one wire. Fig. 9
Fig. 9
Fig. 9
Fig. 9Fig. 9
a.
This allows for an accessory 12V port to remain available.
9.
Route both power leads along the clutch side of the neck and through the electrical and rear speaker output plug
caddy to the seat area.
Allen 3/16"
Tools Needed:
Tools Needed:
Tools Needed:
Tools Needed: Tools Needed: 10mm
wrench or socket
Torx T-30
Allen 9/64"
Phillips head screw driver
Torx T-40
11/32" wrench or socket
Torx T-25
(1) Mylar cover
(1) Dummy Plug
SYSTEM SETUP - Fig. 13
SYSTEM SETUP - Fig. 13
SYSTEM SETUP - Fig. 13
SYSTEM SETUP - Fig. 13SYSTEM SETUP - Fig. 13
Note: At this time, it is highly recommended to . KICKER recommends that the be set up as follows:
set the amp gain to 0
set the amp gain to 0
set the amp gain to 0
set the amp gain to 0set the amp gain to 0 dip switches
dip switches
dip switches
dip switchesdip switches
Input Gain controls – 0
Fader – On Input
level – HI
HI-PASS – Amp 1: 80 Hz (For Front)
Amp 2: 60Hz (6 x 9) 
80Hz (6.5” Tour Pack)
14. Plug the radio in, but do not reinstall it until the gain has been set.
15. if you are not using rear speakers it is recommended to Test component function and set the gain to optimize system performance.
leave the amp 2 gain turned all the way down.
16. Carefully reassemble the motorcycle and enjoy your new audio system!
Note: If you are not using rear speakers you will need to connect the Dummy Plug (fig. 15) to the rear speaker connector under the seat.
For questions, please contact KICKER Technical Support at 800-256-0808, M-F 8:00 am – 5:00 pm CST or email at support@kicker.com.
KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 50 30523HDR154-F-202
1
1
1
11
2
2
2
22
3
3
3
33
4
4
4
44
5
5
5
55
6
6
6
66
7
7
7
77
8
8
8
88
10.
Remove the radio.
a.
Unplug the four connectors on the back of the radio.
b.
Remove the four 3/16" allen head bolts holding the radio to the chassis.
c.
Gently remove the radio from the chassis.
11.
Install the KPX300.4 amplifier onto bracket with supplied hardware.
a.
Slide the end of the amplifier with the power connector port into the bracket and fasten with supplied hardware.
b.
Install the 9/64" allen head bolts from the bottom and fasten the 11/32" locknuts onto the amplifier. Fig. 10
Fig. 10
Fig. 10
Fig. 10Fig. 10
12.
Carefully install bracket/amplifier assembly onto radio chassis by installing the assembly through the radio face port in the fairing and sliding the
tabs of the bracket over the chassis. Fig 11
Fig 11
Fig 11
Fig 11Fig 11
a.
a.
a.
a.a.
Bracket must be angled through radio opening. Fig. 11a
Fig. 11a
Fig. 11a
Fig. 11aFig. 11a
13.
Attach amplifier to the harnesses power, speaker and input signal plugs. Fig. 12
Fig. 12
Fig. 12
Fig. 12Fig. 12
AMP INST
AMP INST
AMP INST
AMP INSTAMP INSTALLA
ALLA
ALLA
ALLAALLATION
TION
TION
TIONTION
12
12
12
1212
11
11
11
1111
11a
11a
11a
11a11a
8a
8a
8a
8a8a
10
10
10
1010
9
9
9
99
13
13
13
1313
14
14
14
1414
Note: At this time it is highly recommended to use the included Mylar sticker to cover the dip switches as seen in Fig. 14
Fig. 14
Fig. 14
Fig. 14Fig. 14
1
1
1
115
5
5
55

Product specificaties

Merk: Kicker
Categorie: Niet gecategoriseerd
Model: 50HDR154

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker 50HDR154 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Kicker

Kicker

Kicker 50HDS962 Handleiding

7 Mei 2024
Kicker

Kicker 50HDR154 Handleiding

7 Mei 2024
Kicker

Kicker 50HDS144 Handleiding

7 Mei 2024
Kicker

Kicker SF150SC15 Handleiding

6 Mei 2023
Kicker

Kicker KMLC Handleiding

4 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Protector

Protector AS-5030.3 V2 Handleiding

21 December 2024
Sabrent

Sabrent AU-MMCW Handleiding

21 December 2024
Sabrent

Sabrent AU-2X35 Handleiding

21 December 2024
Sabrent

Sabrent CB-RS232 Handleiding

21 December 2024
Owon

Owon 500W Handleiding

21 December 2024
Owon

Owon 300W Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ4-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-ROCKET-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-HTSS Handleiding

21 December 2024