JL Audio Stealthbox SB-T-TUNCNSL2/10W3v3 Handleiding

JL Audio Niet gecategoriseerd Stealthbox SB-T-TUNCNSL2/10W3v3

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-T-TUNCNSL2/10W3v3 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB- T- T U N C N S L 2 / 1 0 W 3 v 2 , J L AU D I O , I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 8 0 R e v i s i o n 4 / 6 / 2 0 0 5Pag e 1

for the

SB-T-TUNCNSL2/10W3v2

(‘03-Up Toyota Tundra Access & Double Cab

with front bucket seats and center console)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

Using a 14mm socket, remove the

four bolts that secure the passenger side front

seat.

STEP 2:

Tilt the seat to the rear, unplug the

exposed wire assembly, remove the seat from

the truck.

STEP 3:

Remove the front storage access

door. Using a 10mm socket, remove the

exposed bolts.

STEP 4:

With the main storage door open,

grab ahold of the black cup holder section

and pull up.

STEP 5:

Using a 10mm socket, remove the

exposed bolts. Also remove the bolts that are

located at the bottom of the main storage

bucket.

STEP 6:

Remove the plastic buttons that are

located on each side of the center console.

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

➔➔

➔ ➔

➔➔➔

STEP 7: Slide the center console to the rear of

truck.This will allow exposer of the 12v plug wires.

Unplug and then remove the center console from

truck.

*Tundra Access Cab Only*

Keep the air ducts inside the truck, for now.

STEP 11: Back inside the truck. Remove the black

bracket that is mounted to the floor of the

truck(not pictured).

*Tundra Access Cab Only*

Using a 1/2” drill bit and drill. Enlarging the mounting

holes from the bracket.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: *Tundra Access Cab Only*

With the center console out of the truck, flip up

side down. Remove the two air duct ears that are

located to the rear of the center console.

*Tundra Access Cab Only*

STEP 12: Cut 1-1/2” off of each carpet flap, that is

located in front of the mounting holes, from

STEP10.

➔

*Tundra Access Cab Only*

STEP 13(a): Place only one of the supplied wax

squares into this location.

Place the middle of the supplied wax square, 4-3/4”

back from the front consoles metal mounting brack-

et.

*Tundra Double Cab Only*

STEP 13(b)

FRONT WAX SQUARE

Place the middle of one of the supplied wax

squares, 4-3/4” back from the front consoles metal

mounting bracket.

REAR WAX SQUARES

Place the middle of the remaining pair of supplied

wax squares, 1-3/4” back from the center console

rear mounting holes.

STEP 9: Remove the 8 screws that is securing

the black plastic support to the outer console. Not

all circles represent all 8 screws.

There are a pair of screws on each side of the con-

sole that need to be removed.

STEP 10: *Tundra Access Cab Only*

Now it is time to remove those air ducts from

STEP 7. With the ducts removed, you will need to

cut both ducts. Place the ducts so the front of the

ducts are facing to the right.

Driver’s side: Measure and mark 3/4” from front

of foam tape, back. Cut at location.

Passenger’s side: Cut at the middle of the foam

tape.

SB-T- T UN C N SL2 / 1 0 W 3 v2 , JL AU D I O, I n c 2 0 05 She e t S K U # 01 1 1 8 0 R e vis i o n 4 /6 / 20 0 5Pag e 2

w w w . j l a u d i o . c o m

Passenger’s side

middle

Driver’s side

3/4”

4-3/4” 6-1/2”

1-3/4”

➔

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 14: Thread in the three supplied socket cup

set screws into the Stealthbox. Make sure that the

socket ends are on the outside of the Stealthbox.

The rear(left side of pic) threaded rods need to

protrude about 1 1/4” out of the Stealthbox.The

front socket cup set screw needs to protrude about

3/4”.

Place the Stealthbox into location. Slide the rear

socket cup set screw through the drilled out holes

from STEP10. Press firmly on the front of the

Stealthbox, marking the wax square.

STEP 16(a): *Tundra Access Cab Only*

Remove the Stealthbox.You should have an impres-

sion on the wax square.

*CAUTION*

Before drilling, make sure that you are not going to

be drilling into any gas lines, brake lines, transmission

lines, electrical wiring, transfer case(4x4 vehicles) or

anything else that might cause a reduction in your

weekly pay. Always wear eye protection when drilling.

With the use of a 1/2” drill bit and drill. Drill out the

floor at the impression on the wax square

STEP 16(b): *Tundra Double Cab Only*

Remove the Stealthbox.You should have an impres-

sion on the wax square.

*CAUTION*

Before drilling, make sure that you are not going to

be drilling into any gas lines, brake lines, transmission

lines, electrical wiring, transfer case(4x4 vehicles) or

anything else that might cause a reduction in your

weekly pay. Always wear eye protection when drilling.

With the use of a 1/2” drill bit and drill. Drill out the

floor at the impression on the wax square

SB- T- T U N C N SL 2 / 1 0 W 3 v 2 , J L AU D I O, I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 8 0 R e v i s i o n 4 / 6 / 2 0 0 5Pag e 3

w w w . j l a u d i o . c o m

STEP 15: Place the Stealthbox into position, Press

down firmly.

Product specificaties

Merk:	JL Audio
Categorie:	Niet gecategoriseerd
Model:	Stealthbox SB-T-TUNCNSL2/10W3v3

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-T-TUNCNSL2/10W3v3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd JL Audio

JL Audio Stealthbox SB-F-ESCP/10W1v3 Handleiding

15 November 2024

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Handleiding

15 November 2024

JL Audio MediaMaster 55-HR Handleiding

7 Augustus 2024

JL Audio MediaMaster 55 Handleiding

7 Augustus 2024

JL Audio MBT-RXv2 Handleiding

9 Juli 2024

JL Audio MBT-CRXv3 Handleiding

9 Juli 2024

JL Audio Stealthbox SBX-F-MAVG1/10TW1 Handleiding

10 Juni 2024

JL Audio Stealthbox SBX-T-TACDCG3/10TW3 Handleiding

10 Juni 2024

JL Audio MediaMaster MM105-HR Handleiding

11 Maart 2024

JL Audio JLINK RX Handleiding

8 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024

Kolcraft MLB New York Yankees Handleiding

26 November 2024

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024

Nedis POCO106 Handleiding

26 November 2024

Nedis BTSM1GY Handleiding

26 November 2024

Turbosound TPOLEAJ-01 Handleiding

26 November 2024

Turbosound TSTAND-01 Handleiding

26 November 2024

IFM TAD981 Handleiding

26 November 2024

IFM TAD961 Handleiding

26 November 2024