JL Audio Stealthbox SB-F-ESCP/10W1v3 Handleiding

JL Audio Niet gecategoriseerd Stealthbox SB-F-ESCP/10W1v3

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-F-ESCP/10W1v3 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
I N S T A L L A T I O N G U I D E
for the
SB-F-ESCP/10W1v2
SKU#94440
Ford Escape, Mazda Tribute - 2001+
Mercury Mariner - 2005+
Thank you for choosing a JL Audio Stealthbox
® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox
® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Remove the cover in front of the pocket as shown.
Continued on Next Page
S T E P 2
This is how it looks after removing the cover.
S T E P 3
Remove the woofer from the Stealthbox®. Hold the
enclosure in place and use a marker to mark the interior
panel through the hole in the back of the Stealthbox®
SB-F-ESCP/10W1V2 INSTR_SKU# 011286
INSTALLATION
D I F F I C U LT Y :
35
OUT
OF
ESTIMATED TIME:
23 HOURS
Continued on Next Page
SB-F-ESCP/10W1V2 INSTR_SKU# 011286
S T E P 6
Remove bottom plastic trim piece from rear left door
opening.
S T E P 4
Drill a 1” hole in the interior panel where marked as STEP 3
as shown.
Note: Before drilling, make sure that you are not
going to be drilling into any gas lines, brake lines,
transmission lines, electrical wiring, transfer case (4x4
vehicles) or anything else that might cause a reduc-
tion in your weekly pay. Always wear eye protection
when drilling!
Page 2 • JL Audio, Inc 2008
S T E P 9
This shows the holes where the bracket mounts.
S T E P 1 0 D E T A I L 1
The bracket will be mounted as shown at left in the older
model vehicles.
S T E P 1 0
Mount the bracket.
The bracket will be oriented as shown with all three bolts in a
straight line in the newer vehicles.
For the older models, the bracket will be mounted upside
down to the photo at left with the stud threaded into the
“triangular” hole and, above the two mounting bolts as
shown below
Please refer to the detail pictures for
further clarification.
S T E P 8
The interior with the side panel removed. Note where the
bracket had been previously installed
S T E P 5
Remove bottom trunk plastic trim panel as
shown.
S T E P 7
Remove side panel as shown.
SB-F-ESCP/10W1V2 INSTR_SKU# 011286
Page 5• JL Audio, Inc 2008
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011286 01-22-2009 • Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
w w w . j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
2) 1/4-20 x 1 1/4” Hex Head Bolt 2) 1/4-20 Hex Hed Nut
2) 1/4” Split Lock Washer 2) 1/4” Flat Washer
1) 3/8” Split Lock Washer 1) 3/8” Flat Washer
1) 3/8-16 x 2 1/4” Allen Head Stud 1) 1” Spacer
1) Custom Mount bracket
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10w1v2-4
Nominal Impedance: 4 ohms
Continuous Power Handling: 300watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2
when being used to power your Stealthbox ®.
The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 5”x 7” / 6”x 8”- Front Doors
Fits JL Audio Models: TR570-CXi, C5-570, C5-570x & ZR570-CSi
Rear Speaker Size / Location: 5”x 7” / 6”x 8”- Rear Door
Fits JL Audio Models: TR570-CXi, C5-570x
S T E P 1 1
Expand the round hole in the interior panel from STEP 4
as shown, re-install all of the the interior panels that were
removed earlier, place the 1” Spacer (included) over the Stud
as shown.
S T E P 1 3
Mount woofer to the box . place grill over the speaker,
secure the woofer and you are done.
C O N G R A T U L A T I O N S !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 1 0 D E T A I L 2
This is how the hardware should be configured for the
bracket and, the Stealthbox®.
S T E P 1 2
Put the box in the panel and line it up with the bolt. Make
sure to run speaker wire from the enclosure to the location of
the amp before securing it to the vehicle.
1” SPACER
INTERIOR PANEL
SPLIT LOCK WASHER
FLAT WASHER
STEALTHBOX WALL
HEX NUT
VEHICLE SHEET METAL
ALLEN HEAD STUD
HEX NUT
MOUNTING BRACKET
HEX HEAD BOLT
FLAT WASHER
SPLIT LOCK WASHER
VIEWED FROM ABOVE LOOKING DOWN
VEHICLE SHEET METAL

Product specificaties

Merk: JL Audio
Categorie: Niet gecategoriseerd
Model: Stealthbox SB-F-ESCP/10W1v3

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-F-ESCP/10W1v3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd JL Audio

JL Audio

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/BK Handleiding

7 December 2024
JL Audio

JL Audio Stealthbox SB-F-ESCP/10W1v3 Handleiding

15 November 2024
JL Audio

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Handleiding

15 November 2024
JL Audio

JL Audio MediaMaster 55-HR Handleiding

7 Augustus 2024
JL Audio

JL Audio MediaMaster 55 Handleiding

7 Augustus 2024
JL Audio

JL Audio MBT-RXv2 Handleiding

9 Juli 2024
JL Audio

JL Audio MBT-CRXv3 Handleiding

9 Juli 2024
JL Audio

JL Audio Stealthbox SBX-F-MAVG1/10TW1 Handleiding

10 Juni 2024
JL Audio

JL Audio Stealthbox SBX-T-TACDCG3/10TW3 Handleiding

10 Juni 2024
JL Audio

JL Audio MediaMaster MM105-HR Handleiding

11 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Protector

Protector AS-5030.3 V2 Handleiding

21 December 2024
Sabrent

Sabrent AU-MMCW Handleiding

21 December 2024
Sabrent

Sabrent AU-2X35 Handleiding

21 December 2024
Sabrent

Sabrent CB-RS232 Handleiding

21 December 2024
Owon

Owon 500W Handleiding

21 December 2024
Owon

Owon 300W Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ4-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-ROCKET-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-HTSS Handleiding

21 December 2024